JIMWAY EV1011SC5C-06 LED Ceiling Flush Mount Instruction Manual
- June 16, 2024
- JIMWAY
Table of Contents
JIMWAY EV1011SC5C-06 LED Ceiling Flush Mount
SAFETY INFORMATION
- Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box.
WARNING: Disconnect the power prior to removing or installing a light fixture.
- Consult a qualified electrician if you have any electrical questions or need to replace the driver.
- If you have any non-electrical questions about this fixture, please contact our Customer Service Team at 1-855-573-6156.
PLANNING THE INSTALLATION
Read all instructions before assembly and installation. Before starting installation of the fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box. To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard.
NOTE: Keep your receipt and these instructions for Proof of Purchase.
TOOLS REQUIRED
PACKAGE CONTENTS
PACKAGE CONTENTS (not to scale)
INSTALLATION
- Thread the nipple (HH) onto the mounting bracket (JJ) and secure it in place with a hex nut (CC).
- Thread the mounting screws (GG) through the mounting bracket (JJ) and all the way into the holes of the outlet box.
NOTE: If you have electrical questions consult your local electrical code for approved grounding methods.
-
Insert the quick connector (11) into the back of the fixture pan (BB).
-
Attach the black supply wire to the black quick connector (II) wire using a wire nut (DD).
-
Attach the white supply wire to the white quick connector (II) wire using a wire nut (DD).
-
Connect the fixture ground wire and the supply ground wire together using a wire nut (DD).
-
Wrap all wire connections with electrical tape for a more secure connection.
-
Carefully tuck all the wires and wire connections into the outlet box.
-
Place the fixture pan (BB) over the outlet box and feed the nipple (HH) through the center of the fixture pan (BB).
-
Place the washer (FF) over the nipple (HH). Secure the fixture in place with the thumb nut (EE).
-
Tighten the thumb nut (EE) so that the fixture pan (BB) is secured flush against the ceiling.
-
Slide the acrylic shade (AA) onto the fixture pan (BB) and turn all the latches to secure the acrylic shade (AA).
OPERATION & CLEANING
OPERATION
NOTE
- Do not use any cleaners with chemicals, solvents, or harsh abrasives.
- Use only a dry soft cloth to dust or wipe carefully.
EXTERIOR MAINTENANCE
- Use a dry or slightly dampened clean cloth and wipe the surface of the fixture.
INTERIOR MAINTENANCE
- Disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box.
- Use a dry or slightly dampened clean cloth to wipe the interior surface of the fixture.
TROUBLESHOOTING
WARRANTY
WHAT IS COVERED
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of five (5) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect or mishandling.
WHAT IS NOT COVERED
This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear.
The manufacturer does not warrant and specially disclaims any warranty, whether expressed or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor/expense costs involved in the replacement or repair of said product.
Questions, problems, missing parts?
- Before returning to the store, call Envirolite Customer Service
- 8 a.m. – 6 p.m., EST, Monday – Friday
- 1-855-573-6156