HINKLEY 46994HB LED Convertible Chandelier Facet Instruction Manual

HINKLEY 46994HB LED Convertible Chandelier Facet

Specifications

• Model: UFN/P 991-46994
• Brand: HINKLEY
• Dimensions: N/A
• Weight: N/A
• Power Supply: Requires wiring and connection to a power source
• Bulb Type: Requires medium base bulbs (not supplied)
• Installation: Can be mounted as a flush mount or using a canopy

OVERVIEW

Mounting instructions

1. Find a clear area in which you can work.
2. Unpack the fixture and glass from the carton.
3. Carefully review instructions before assembly.

STEP 1

1. Shut off the electrical current before starting. If the fixture you are replacing is turned on and off by a wall switch, simply turn the switch off. If not, remove the appropriate fuse (or open the circuit breakers) until the fixture is dead.
   • DO NOT restore current – either by fuse, breaker or switch – until the new fixture is completely wired and in place.

STEP 2

1. In the following order: take the retainer ring (L), and canopy (H) and slide them over the stems (R) attached previously.
2. Thread supply wires (S) through the center of the swivel (E) that is attached to the mounting strap (A).
3. Slide the swivel with a mounting strap along the wire and thread the end of the swivel into the top of the stems (R).
4. Lift the fixture and attach the mounting strap (A) to junction box (C) using 2-8/32 screws (B) not provided.
5. Make all necessary electrical connections following the instruction sheet (IS-18) provided. Ground wire (D) can be attached to the mounting strap (A)  using a green ground screw (G).
6. Slip canopy (H) up along rods (R) and over mounting strap with swivel and hold in position.
7. Slip retainer ring (I) up to canopy and thread onto coupler (F), to secure canopy.

Note : Fixture can be converted to a flush mount by removing swivel (E) and using the supplied 4″ stem

Assembly Instructions

1. Place small diffuser (9) into small shade (10)
2. Secure arms (5) to a small shade(10) using  screws (6)
3. Place large diffuser (7) into large shade (8)
4. Secure large shade (8) to top pan (1) using screws (3)
5. Secure arms from small shade (5) to top pan (1) using screws (2)
6. Use a plastic plug to cover mounting holes
7. Lamp fixture with appropriate medium base bulbs (4) (not supplied)
8. The fixture can now be powered on

I.S. 18 wiring grounding instructions

SAFE TY WARNI NG: READ WIRIN G AND GR OUNDING INSTRUCTION NS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSU LT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS

wiring instructions

Indoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth,  unmarked side of the two-conduc tor cord) to positive fixture lead (B) with an appropriately sized twist on connector – see Dra wings 1 or 2.
2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Please refer to the grounding instructions below to complete all electrical connections

Outdoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive fixture lead (B) with an appropriately sized twist on the connector – see Drawings 2 or 3.
2. Connect negative supply wire (C) (typically white or ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Cover the open end of connectors with silicone sealant to form a watertight seal. X If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a fixture mounting platform specially.
4. Please refer to the grounding instructions below to complete all electrical connections.

grounding instructions

Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap (M ) with the ground screw (S) – see Draw in g 1.
Note: On straps for screw-supported fixtures, first install the two mounting screws in the strap. Any remaining tapped hole may be used for the ground screw.

Chain Hung Fixture es
Loop fixture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on the fixture mounting strap (M) and connect to the loose end of the fixture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Draw in g 2.

Post-Mou nt Fixtur es
Connect fixture ground wire (E) (typically copper or green plastic coated) to the power supply ground with an appropriately sized twist-on connector inside the post. Cover the open end of the connector with silicone sealant to form a watertight seal – see Drawing 3.

FAQ

• Q: What bulbs are compatible with this fixture?
  • A: This fixture requires medium base bulbs, which are not supplied. Please ensure you use appropriate medium base bulbs.
• Q: Can this fixture be mounted as a flush mount?
  • A: Yes, this fixture can be converted to a flush mount by removing the swivel (E) and using the supplied 4-stem canopy.
• Q: Are the wiring and grounding instructions provided in multiple languages?
  • A: Yes, the wiring and grounding instructions are provided in  English, Spanish, and French.

HINKLEY
33000 Pin Oak Parkway, Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkley.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>