WhirShril WS-S-50DF Safe Box for Home Instruction Manual
- June 16, 2024
- WhirShril
Table of Contents
WhirShril WS-S-50DF Safe Box for Home Instruction Manual
Product Description
- Box
- Door
- Panel
- Handle
- Feet
Panel Introduction
- Fingerprint scanner
- Indicator light
- Digital keypad
- Handle
- Override key hole cover
- Override key hole
First Open-Override Keys Open
Step 1
Remove the override key hole cover.
Step 2
Instert the override key and turn it clockwide to the limit position to open
the safe.
Step 3
After the override key is restored to its original position pull it out.
Install 4 AA batteries into the battery compartment on the top of the back
cover of the door. At this stage, the door bolts are in extended state. Be
aware not to close the door when bolts are extended. That will damage the
paint.
Step 4
Finished battery installation, restore the override lock cover to original.
Add Fingerprint
(You can set 30pcs fingerprints.)
Press “Green” button on the back of the door based on situation of opening of safe box. Until hears two beeps and Light turns yellow.
Place finger on the scaner until user hear one beep remove the finger and place it back again for 4 times.
If user hears two beeps means fingerprint set success and light turns green.
If user hears three beeps and light turns red means fingerprint set is failed or fingerprint is already exists.
*Use this way, You can set maximum 30pcs fingerprints.
Add password
(You can set 2 groups passwords.)
Password 1
The default password of the safe is 123456. For security. we strongly recommend that you change this password. Follow this procedure. Wake up keypad, Press “00” on the keypad first, Then press green button on the back of the door. Enter 3 to 12 digits code end with “#”. If user hears two beeps and light turns green means password set success. If user hears three beeps and light turns red means password set is failed.
Password 2
If you need to add a second set of passwordsWake up keypad, Press “11” on the keypad first, Then press green button on the back of the door. Enter 3 to 12 digits code end with “#”. If user hears two beeps and light turns green means password set success. If user hears three beeps and light turns red means password set is failed.
Please remember the fingerprints or passwords you have set.
Delete fingerprint and password
Press “Green” button about 5 seconds then hear long deep means all the fingerprints and passwords were deleted success. And turn back to factory settings. Any fingerprint can open the safe box.
Other function
Vibration alarm
In the sleep state, touch the wake-up touch screen, press the * key 1o hear a “beep, and the number key light i off, indicating that the alert state has been entered. The safe. will alarm when it s vibrated. After the alarm, enter the correct fingerprint or password. After 5 seconds, the alert state will be released automatically. If the correct fingerprint or password is not input, the alarm will stop automatically 30 seconds later, but the alert will not be lifted.
Wrong entry alarm
“The safe gives an alarm when the wrong password is Input for 3 consecutive
times or the wrong fingerprint s input for 5 consecutive times.
Under voltage warning
The system uses four 1.5V alkaline batteries. I the voltage s Insufficient,
the buzzer will send out “beep” twice after opening the door to remind the
user 1o replace the battery. in time when the power Is low.
Turn off/on the tone
Touch to wake up the touch screen, input “1 1 and #’ to turn off all sounds,
and then “1 1 and #” again to tum on the prompt tone.
Emergency open
If the battery voltage is insufficient, the emergency power supply or mechanical emergency key can be used to open the door.
Method 1
Method 2
Default setting
Press the green button on the mechanism for 5 seconds, and the system will restore the initialization settings and clear all fingerprints and passwords.
NOTE
- Please be sure not to put the emergency key and emergency power supply in the safe, in case that the safe cannot be opened due to forgotten password or Insufficient voltage.
- To improve the accuracy of fingerprint identification, users can refer to the following suggestions 1.
- It is recommended that each user register 2-3 fingerprints.
- Itis recommended that wormen and children try to use their thumbs or middle fingers to set fingerprints.
- When setting fingerprints, the force of finger pressing should be as uniform as possible. It should not be too heavy or too light. It is recommended to press the finger Tightly.
- It is recommended to press the same finger at multiple angles when setting fingerprint.
- When selecting batteries, it is recommended to use high-quality high-performance alkaline batteries. Do not use carbon batteries.
Specifications
- Working voltage: 42V-68V
- Under voltage warning: 45V=02V
- Standby current: <50uA
- Fingerprint storge: 30
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>