SONY DSC-W5 Digital Still Camera User Manual
- June 16, 2024
- Sony
Table of Contents
- DSC-W5 Digital Still Camera
- Product Information
- Specifications
- Product Usage Instructions
- How to Use the Camera
- Exposure Control
- White Balance
- Flash
- FAQ
- Q: How do I change the battery in the camera?
- Q: Can I use rechargeable batteries with this camera?
- Q: How do I transfer my photos and videos to a computer?
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
DSC-W5 Digital Still Camera
Product Information
Specifications
-
Image Device: DSC-W7/W17: 9.11 mm (1/1.8 type) color CCD,
Primary color filter DSC-W5/W15: 9.04 mm (1/1.8 type) color CCD,
Primary color filter -
Total Pixel Number: DSC-W7/W17: Approx. 7,410,000 pixels
DSC-W5/W15: Approx. 5,255,000 pixels -
Effective Pixel Number: DSC-W7/W17: Approx. 7,201,000 pixels
DSC-W5/W15: Approx. 5,090,000 pixels -
Lens: Carl Zeiss Vario-Tessar 3 zoom lens f = 7.9 – 23.7 mm (38
– 114 mm when converted to a 35 mm still camera) F2.8 – 5.2 -
Exposure Control: Automatic exposure, Manual exposure, Scene
Selection (7 modes) -
White Balance: Automatic, Daylight, Cloudy, Fluorescent,
Incandescent, Flash -
File Format: Still images – Exif Ver. 2.2 JPEG compliant, DPOF
compatible; Movies – MPEG1 compliant (Monaural) -
Recording Media: Internal memory 32 MB Memory Stick
-
Flash Recommended Distance: (ISO set to Auto) – 0.2 m to 4.5 m
(7 7/8 inches to 14 feet 9 1/4 inches) (W)/0.3 m to 2.5 m (11 7/8
inches to 8 feet 2 1/2 inches) (T) -
Input and Output Connectors: A/V OUT (MONO) jack (Monaural)
Minijack Video – 1 Vp-p, 75 , unbalanced, sync negative Audio – 327
mV (at a 47 k load) Output impedance 2.2 k; USB jack – mini-B USB
communication – Hi-Speed USB (USB 2.0 compliant) -
LCD Screen: 6.2 cm (2.5 type) TFT drive
-
Power: HR 15/51:HR6 (size AA) Nickel-Metal Hydride batteries
(2), 2.4 V R6 (size AA) Alkaline batteries (2, not supplied), 3 V
AC-LS5K AC Adaptor (not supplied), 4.2 V -
Power Consumption: DSC-W7/W17: 1.2 W DSC-W5/W15: 1.1 W
-
Dimensions: Not provided
-
Mass: Approx. 253 g (8.9 oz) (including two batteries and wrist
strap) -
Microphone: Electret condenser microphone
-
Speaker: Dynamic speaker
-
Exif Print: Compatible
-
PRINT Image Matching III: Compatible
-
PictBridge: Compatible
-
BC-CS2A/CS2B Ni-MH battery charger: Power requirements AC 100
to 240 V, 50/60 Hz, 3 W
Product Usage Instructions
How to Use the Camera
1. Insert the appropriate batteries into the camera.
2. Turn on the camera by pressing the power button.
3. To take a photo, aim the camera at the subject and press the
shutter button halfway to focus. Once the focus is locked, press
the shutter button fully to capture the photo.
4. To record a video, switch the camera to video mode and press
the dedicated video recording button. Press the button again to
stop recording.
5. Use the zoom lever to zoom in or out while framing your
shot.
6. Access the menu options by pressing the menu button. Navigate
through the menu using the arrow buttons and select options using
the enter button.
7. To review your photos and videos, press the playback button.
Use the arrow buttons to navigate through the gallery and press the
enter button to view a selected item.
8. Connect the camera to a computer using the USB cable to
transfer your photos and videos.
Exposure Control
The camera offers automatic exposure, manual exposure, and scene
selection modes. In automatic exposure mode, the camera
automatically adjusts the settings for optimal exposure based on
the lighting conditions. In manual exposure mode, you have control
over settings such as aperture, shutter speed, and ISO. Scene
selection modes allow you to choose from pre-programmed settings
for specific shooting scenarios, such as portrait, landscape, or
sports.
White Balance
The white balance setting determines how the camera adjusts for
different lighting conditions to ensure accurate color
reproduction. The camera offers automatic white balance as well as
preset options for daylight, cloudy, fluorescent, incandescent, and
flash lighting conditions. Choose the appropriate white balance
setting based on the lighting conditions of your shooting
environment.
Flash
The camera is equipped with a built-in flash for illuminating
subjects in low-light conditions. The recommended flash distance
varies depending on the ISO setting. Make sure to set the ISO to
Auto for accurate flash range calculations. The flash can be
manually turned on or off, or set to auto mode where it will
activate automatically when needed.
FAQ
Q: How do I change the battery in the camera?
A: To change the battery, open the battery compartment door
located on the bottom of the camera. Remove the old batteries and
insert fresh ones according to the polarity markings. Close the
battery compartment door securely.
Q: Can I use rechargeable batteries with this camera?
A: Yes, you can use HR 15/51:HR6 (size AA) Nickel-Metal Hydride
batteries as a rechargeable option. Make sure to follow the
manufacturer’s instructions for charging and using rechargeable
batteries.
Q: How do I transfer my photos and videos to a computer?
A: Connect the camera to your computer using the provided USB
cable. Turn on the camera and select the USB communication option
from the menu. Your computer should recognize the camera as a
removable storage device. Open the file explorer or photo
management software on your computer and navigate to the camera’s
storage. Copy or move the desired files to your computer’s hard
drive.
DSC-W5/W7/W15/W17
SERVICE MANUAL
Ver. 1.5 2007.09
Revision History
How to use Acrobat Reader
2 LEVEL
DSC-W5/W7
US Model Canadian Model Argentine Model Brazilian Model Japanese Model
DSC-W5/W7/W15/W17
AEP Model UK Model E Model
Australian Model Hong Kong Model
Korea Model Tourist Model
DSC-W5/W7/W15
Chinese Model
Link
SPECIFICATIONS SERVICE NOTE DISASSEMBLY
Photo: DSC-W5/Silver
BLOCK DIAGRAMS FRAME SCHEMATIC DIAGRAM SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS REPAIR PARTS LIST
· For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (9-876-856-51). · For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (9-876-856-41). · This service manual contains information for Japanese model as well. · Reference No. search on printed wiring boards is available. · Table for Differences of Function of Each Model · Note in Lens Frame Installation · Method for Copying or Erasing the Data in Internal Memory. · Exchange Method of Barrier Assy
On the CH-168 and SY-001 boards This service manual procides the information that is premised the circuit board replacement service and not intended repair inside the CH-168 and SY-001 boards. Therefore, schematic diagram, printed wiring board and electrical parts list of the CH-168 and SY-001 boards are not shown. The following pages are not shown.
Schematic diagrams ……………… Pages 4-11 to 4-30 Printed wiring boards ……………. Pages 4-39 to 4-42 Waveforms ………………………….. Pages 4-45 and 4-46 Mounted parts location ………….. Pages 4-48 Electrical parts list ………………… Pages 5-7 and 5-9 to 5-12
DIGITAL STILL CAMERA
The above-described information is shown in service manual Level 3.
DSC-W5/W7/W15/W17 9-876-856-31
Sony EMCS Co.
2007I0500-1
© 2007.9 Published by Kohda TEC
Camera
[System]
Image device
DSC-W7/W17: 9.11 mm (1/1.8 type) color CCD, Primary color filter DSC-W5/W15: 9.04 mm (1/1.8 type) color CCD, Primary color filter
Total pixel number of camera DSC-W7/W17: Approx. 7 410 000 pixels DSC-W5/W15: Approx. 5 255 000 pixels
Effective pixel number of camera DSC-W7/W17: Approx. 7 201 000 pixels DSC-W5/W15: Approx. 5 090 000 pixels
Lens
Carl Zeiss Vario-Tessar
3 zoom lens
f = 7.9 – 23.7 mm (38 – 114 mm
when converted to a 35 mm still
camera)
F2.8 – 5.2
Exposure control Automatic exposure, Manual exposure, Scene Selection (7 modes)
White balance
Automatic, Daylight, Cloudy, Fluorescent, Incandescent, Flash
File format (DCF compliant) Still images: Exif Ver. 2.2 JPEG compliant, DPOF compatible Movies: MPEG1 compliant (Monaural)
Recording media Internal memory 32 MB Memor y Stick
Flash
Recommended distance (ISO set to Auto): 0.2 m to 4.5 m (7 7/8 inches to 14 feet 9 1/4 inches) (W)/0.3 m to 2.5 m (11 7/8 inches to 8 feet 2 1/2 inches) (T)
SPECIFICATIONS
[Input and Output connectors]
A/V OUT (MONO) jack (Monaural) Minijack Video: 1 Vp-p, 75 , unbalanced, sync negative Audio: 327 mV (at a 47 k load) Output impedance 2.2 k
USB jack
mini-B
USB communication
Hi-Speed USB (USB 2.0 compliant)
[LCD screen]
LCD panel
6.2 cm (2.5 type) TFT drive
Total number of dots 115 200 (480×240) dots
[Power, general]
Power
HR 15/51:HR6 (size AA) Nickel-Metal Hydride batteries (2), 2.4 V R6 (size AA) Alkaline batteries (2, not supplied), 3 V AC-LS5K AC Acaptor (not supplied), 4.2 V
Power consumption (during shooting with the LCD screen on)
DSC-W7/W17: 1.2 W DSC-W5/W15: 1.1 W
Operating temperature 0°C to +40°C (+32°F to +104°F)
Storage temperature -20°C to +60°C (-4°F to +140°F)
Dimensions
91×60×37.1 mm (3 5/8×2 3/8×1 1/2 inches) (W/H/D, excluding maximum protrusions)
Mass
Approx. 253 g (8.9 oz) (including two batterries and wrist strap)
Microphone Electret condenser microphone
Speaker
Dynamic speaker
Exif Print
Compatible
PRINT Image Matching III Compatible
PictBridge
Compatible
BC-CS2A/CS2B Ni-MH battery charger
Power requirements AC 100 to 240 V, 50/60 Hz, 3 W
Output voltage AA: DC 1.4V 400 mA × 2 AAA: DC 1.4 V 160 mA × 2
Operating temperature 0°C to +40°C (+32°F to +104°F)
Storage temperature -20°C to +60°C (-4°F to +140°F)
Dimensions
Approx. 71×30×91 mm (2 7/8×1 3/16×3 5/8 inches) (W/H/D)
Mass
Approx. 90 g (3 oz)
Design and specifications are subject to change without notice.
DSC-W5/W7/W15/W17
— 2 —
Table for differences of function
Model
DSC-W5
Destination
US, CND, AEP, UK, E, AUS, HK, CH, KR, AR, BR, J, JE
CCD imager Total pixel (Effective pixel)
5 255 000 pixels (5 090 000 pixels)
CD board
CD-545
Note: DSC-W15/W17 are the same as DSC-W5/W7 except accessories and packing materials.
DSC-W7
US, CND, AEP, UK, E, AUS, HK, CH, KR, AR, BR, J, JE
7 410 000 pixels (7 201 000pixels)
CD-546
DSC-W15
AEP, UK, E, AUS, HK, CH,
KR, JE
5 255 000 pixels (5 090 000 pixels)
CD-545
DSC-W17
AEP, UK E, AUS, HK,
KR, JE
7 410 000 pixels (7 201 000pixels)
CD-546
· Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC
DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL
OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET
LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS
DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes and bridges.
2. Check the interboard wiring to ensure that no wires are “pinched” or
contact high-wattage resistors.
Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.
: LEAD FREE MARK Unleaded solder has the following characteristics.
4. Look for parts which, through functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their replacement.
5. Check the B+ voltage to see it is at the values specified. 6. FLEXIBLE
Circuit Board Repairing
· Keep the temperature of the soldering iron around 270°C during repairing.
· Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!
· Do not touch the soldering iron on the same conductor of the · Strong viscosity
circuit board (within 3 times).
Unleaded solder is more viscous (sticky, less prone to flow) than
· Be careful not to apply force on the conductor when soldering or unsoldering.
ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. · Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
DSC-W5/W7/W15/W17
also be added to ordinary solder.
— 3 —
TABLE OF CONTENTS
Section
Title
Page Section
Title
1. SERVICE NOTE 1-1. Note for Repair
································································ 1-1 1-2.
Discharging of The SY-001 Board’s Charging Capacitor
(C901)
··············································································
1-1 1-3. Note in Lens Frame Installation
······································ 1-2 1-4. Description on Self-diagnosis
Display ···························· 1-2 1-5. Method for Copying or Erasing
the Data in Internal
Memory
···········································································
1-3 1-6. Process After Fixing Flash Error
····································· 1-4
2. DISASSEMBLY 2-1. Disassembly ····································································· 2-1 2-2. SY-001 Board Service Position ······································· 2-3 2-3. Exchange Method of Barrier Assy ·································· 2-5 2-3-1. Peel Off Old Ornamental Ring A ···································· 2-5 2-3-2. Remove Old Barrier Assy ················································ 2-6 2-3-3. Install New Barrier Assy ················································· 2-6 2-3-4. Adhere the Ornamental Ring A ······································· 2-7 2-4. Circuit Boards Location ·················································· 2-8
3. BLOCK DIAGRAMS 3-1. Overall Block Diagram (1/2) ··········································· 3-1 3-2. Overall Block Diagram (2/2) ··········································· 3-3 3-3. Power Block Diagram ····················································· 3-5
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. Frame Schematic Diagram ··············································
4-1 4-2. Schematic Diagrams
························································ 4-5
CD-545 FLEXIBLE (CCD IMAGER) ··························· 4-7 CD-545 FLEXIBLE
(CCD IMAGER) ··························· 4-9 SW-001 BOARD (CONTROL SWITCH)
···················· 4-31 CONTROL SWITCH BLCOK
····································· 4-32 4-3. Printed Wiring Boards
··················································· 4-35 CD-545 FLEXIBLE
······················································ 4-37 CD-546 FLEXIBLE
······················································ 4-38 SW-001
········································································· 4-44
4-5. Mounted Parts Location ················································
4-47
5. REPAIR PARTS LIST 5-1. Exploded Views ······························································· 5-2 5-1-1. Overall Assembly ··························································· 5-2 5-1-2. Cabinet (Front) Block ······················································ 5-3 5-1-3. Main Block Assembly ····················································· 5-4 5-1-4. Lens Block Assembly ······················································ 5-5 5-2. Electrical Parts List ························································· 5-6
Page
DSC-W5/W7/W15/W17
— 4 —
1-1. NOTE FOR REPAIR
1. SERVICE NOTE
Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly.
When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
Cut and remove the part of gilt which comes off at the point. (Be careful or some pieces of gilt may be left inside)
When installing a connector, don’t press down at wire of connector. It is possible that a wire is snapped.
1-2. DISCHARGING OF THE SY-001 BOARD’S CHARGING CAPACITOR (C901)
The charging capacitor (C901) of SY-001 board is charged up to the maximum 300
V potential. There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the charged
voltage which is kept without discharging when the main power of the unit is
simply turned off. Therefore, the remaining voltage must be discharged as
described below.
Preparing the Short Jig To preparing the short jig, a small clip is attached
to each end of a resistor of 1 k /1 W (1-215-869-11). Wrap insulating tape
fully around the leads of the resistor to prevent electrical shock.
1 k/1 W
Discharging the Capacitor Short-circuit between the positive and the negative
terminals of charged capacitor with the short jig about 10 seconds.
R:1 k/1 W (Part code: 1-215-869-11)
Wrap insulating tape.
DSC-W5/W7/W15/W17 1-1
1-3. NOTE IN LENS FRAME INSTALLATION
When tightening a screw, have both sides of the lens block assembly so as not
for the load to depend. P2 tapping screw
Lens block assembly
Lens frame assembly
1-4. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY
Self-diagnosis display · C: ss: ss
You can reverse the camera malfunction yourself. (However, contact your Sony
dealer or local authorized Sony service facility when you cannot recover from
the camera malfunction.) · E: ss: ss Contact your Sony dealer or local
authorized Sony service facility.
Display Code
Countermeasure
Cause
C:32:ss Turn the power off and on again.
Trouble with hardware.
C:13:ss
Format the “Memory Stick” or internal “Memory Stick” or internal memory is
memory.
unformatted.
Insert a new “Memory Stick”.
“Memory Stick” is broken.
Turn the power off and on again.
Trouble with internal memory.
E:61:ss Checking of lens drive circuit.
When failed in the focus and zoom initialization.
E:91:ss
Checking of flash unit or replacement Abnormality when flash is being
of flash unit. (Note)
charged.
E:92:ss Insert batteries correctly.
Batteries are not inserted correctly.
Note: After repair, be sure to perfom “1-6. PROCESS AFTER FIXING FLASH ERROR”.
DSC-W5/W7/W15/W17 1-2
Caution Display During Error SYSTEM ERROR FORMAT ERROR
MEMORY STICK ERROR INTERNAL MEMORY ERROR
—
1-5. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the Setup screen. (When
erasing the data, execute formatting the internal memory.)
Note: 1 When replacing the SY-001 board, erase the data in internal memory of
the board before replacement. Note: 2 When replacing the SY-001 board or the
IC381 on the SY-001 board, execute formatting and initialize the internal
memory after
replacement.
Method for Copying the Data in Internal Memory
Copy
Copies all images in the internal memory to a “Memory Stick”.
OK
See the following procedure.
Cancel
Cancels the copying.
1 Insert a “Memory Stick” having 32 MB or larger capacity. 2 Select [OK] with
v on the control button, then press z.
The message “All data in internal memory will be copied Ready?” appears.
3 Select [OK] with v, then z. Copying starts.
Copying 102_COPY
· Use fully charged Nickel-Metal Hydride batteries or the AC Adaptor (not
supplied). If you attempt to copy image files using batteries with little
remaining charge, the batteries may run out, causing copying to fail or
possibly corrupting the data.
· You cannot copy individual images. · The original images in the internal
memory are retained even after copying. To delete the contents of the
internal memory, remove the “Memory Stick” after copying, then execute the
[Format] command in Internal Memory Tool). · You cannot select a folder copied
on a “Memory Stick”. · A (Print order) mark added to an image is deleted when
you copy data.
Method for Formatting the Internal Memory
Format
Formats the internal memory. · Note that formatting irrevocably erases all data in the internal memory, including even protected images.
OK
See the following procedure.
Cancel
Cancels the formatting.
1 Select [OK] with v on the control button, then press z. The message “All
data in internal memory will be erased Ready?” appears.
2 Select [OK] with v, then press z. The format is complete.
DSC-W5/W7/W15/W17 1-3
1-6. PROCESS AFTER FIXING FLASH ERROR
When “FLASH error” (Self-diagnosis Code E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed automatically to disabling charge and flash setting. After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.
Method for Initializing the Flash Error Code
Initialize
Initializes the setting to the default setting.
OK
See the following procedure.
Cancel
Cancels the resetting.
1 Select [OK] with v on the control button, then press z. The message
“Initialize all settings Ready?” appears.
2 Select [OK] with v, then press z. The settings are reset to the default
setting.
· Make sure that the power is not disconnected during resetting.
DSC-W5/W7/W15/W17
1-4E
2. DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1. DISASSEMBLY
qa qs 9
1
0
3
9
6
8
1
14
5
7
2
1 P2 torasuta screw (M1.7) x4 2 Claw x1 3 Cabinet (rear) block assembly 4 Screw (M1.7) x2 5 SW-001 board 6 Flexible board x2: CN451, 452
7 Claw x1 8 BT side cabinet (C) 9 Claw x3 0 SP sheet qa Connector: CN601 qs D901, LCD901
R:1 k/1 W (Part code: 1-215-869-11)
0
Note: High-voltage cautions
7 5
Discharging the Capacitor
Short-circuit between the two
points with the short jig about 10
6
seconds.
9 8
3 2
1 4
1 Screw (M1.7) x2 2 LCD frame 3 Terminal guard 4 Fuse label 5 Remove the control switch block.
6 Connector: CN753 7 Control switch block 8 Connector x2: CN801, 802 9 Remove the cabinet (front) block. 0 Cabinet (front) block
DSC-W5/W7/W15/W17
12 3
1 Ornamental ring A 2 Tapping screw x2 3 Barrier assy
Note: When you exchange rings, be sure to follow the procedure carried on
“2-3. Exchange Method of Barrier Assy” (2-5 page).
2-1
2 4
1 1 Connector: CN001
3 2 Battery holder 3 Connector x2: CN201, 401 4 Lens block
2-2
2-2. SY-001 BOARD SERVICE POSITION
qa qs 9
1
3 1
9 14 2
0
6
8
7 5
3 2
0
7
9
5
6
8
1 4
2 4
1 3
DSC-W5/W7/W15/W17 2-3
Connection cord (DK-2AA) (1-830-351-11)
Batery holder
SW-001 FFC-051
AC power adaptor
AC IN
Control switch block
D901, LCD901 (Note)
Lens block
SY-001 board
A/V cable (Note)
Color monitor
Note: If the A/V cable is connected to the AV OUT (MONO) jack of SY-001 board,
the image can not appear on the LCD screen. If you want to confirm the circuit
of LCD drive or LCD, disconnect the A/V cable.
2-4
2-3. EXCHANGE METHOD OF BARRIER ASSY
Service parts Part Number
1 3-091-427-01 2 X-3954-476-1 3 3-086-156-31
Part Name Ring (A), Ornamental Barrier Assy Tapping screw (P2)
Quantity 1 1 2
Tools used Torque driver Soldering iron Weight about 60g Adhesive (Super X)
(Note) Note: Use adhesive (Super X) or an equivalent article.
Don’t use what becomes white after drying like a quick-drying glue.
1 2 3
2-3-2. REMOVE OLD BARRIER ASSY
1 Remove two screws. * Discard the removed screws.
2 Remove the Barrier Assy. * Discard the removed Barrier Assy.
1
2
1
2-3-1. PEEL OFF OLD ORNAMENTAL RING A
The Ornamental Ring A has adhered to the Barrier Assy strongly and
accordingly, use a soldering iron to weaken the adhesive force. Heat four
circled portions with the soldering iron. Heating temperature is about 300ºC.
Beware of a burn since the entire Ornamental Ring becomes hot. As the
adhesive force of Ornamental Ring A is considerably large, the forced peeling
will damage the group-1 frame.
Insert the tip of tweezers, etc. into a notch of the group-1 frame and prize
the ring. Take extreme care so as not to damage the coated surface of the
group-1 frame. In case of difficult peeling, heat the ring again with the
soldering iron. If this re-heating failed, it may be advisable that the ring
be peeled while heating the portions 1 2 3 4 in the under figure one by one
sequentially.
-
Discard the removed Ornamental Ring A.
-
After removing the Barrier Assy, if the “G1 Dust-Proof Ring” was removed, it must be returned to the home position. In returning the ring, adjust the location of a projection to the lens direction. This is an important part to prevent the dust and light from coming in.
-
After removing the Barrier Assy, take extreme care not to drop dust or foreign substances in the lens barrel.
2-3-3. INSTALL NEW BARRIER ASSY
1 Install new Barrier Assy by paying attention to the projection of the Barrier Assy in relation to the position shown in the under figure.
2 Tighten two screws. * Tightening torque = 0.5 kgf (4.9 N)
4
2
3
Tip
1
Projection 1
2 2
DSC-W5/W7/W15/W17
2-5
2-6
2-3-4. ADHERE THE ORNAMENTAL RING A
Apply an adhesive to four recesses on the top surface of the Barrier Assy.
Do not apply too much adhesive. (Make quantity of adhesives into the quantity
in which a groove hides.)
Meeting a “notch” of the Ornamental Ring A with a “projection” of the group-1
frame, push the Ornamental Ring A into the group-1 frame. The projection of
the spring for preventing static electricity must be tilted.
Put the 60g weight on the Ornamental Ring A so that the Ornamental Ring A does
not float up until the adhesive hardens. Note: Be careful not to give a shock.
- After the weight was put, no gap must be present in full circumference
between Ornamental Ring A and group-1 frame.
A gap, if present, causes the crackle sound NG. * The weight must push in the Ornamental Ring A only.
If the weight is put on the mold part of the Barrier Assy, the Ornamental Ring A will float up.
Notch Adhesive Projection
Adhesive
Completion after 30 minutes.
Adhesive
Do not put the weight on a black mold part.
Adhesive
Not gap in full circumference.
DSC-W5/W7/W15/W17 2-7
2-4. CIRCUIT BOARDS LOCATION SW-001
SY-001 (including CP201 (CH-168 board))
CD-545 flexible (W5/W15)/ CD-546 flexible (W7/W17)
Board Name
Function
CD-545 flexible CCD IMAGER
CD-546 flexible CCD IMAGER
CH-168
CCD SIGNAL PROCESS
(included in SY-001)
SW-001
CONTROL SWITCH
SY-001
CAMERA MODULE, CAMERA DSP, CPU,
(including CP-201 LENS DRIVE, BURST FLASH, SDRAM, AND FLASH,
(CH-168 board)) LCD DRIVE, AUDIO, VIDEO, DC/DC CONVERTER,
FLASH DRIVE, CONNECTOR
DSC-W5/W7/W15/W17
2-8E
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/2) OVERALL BLOCK DIAGRAM (2/2)
POWER BLOCK DIAGRAM
DSC-W5/W7/W15/W17
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
LENS
LENS BLOCK
IRIS (METER)
SHUTTER MOTOR
M
ZOOM MOTOR
M
FOCUS MOTOR
M
IRIS MOTOR
M
FOCUS SENSOR
ZOOM ZOOM FG SENSOR
LENS TEMP SENSOR
CD-545/546 FLEXIBLE BOARD (1/2)
CD-545 : W5/W15 CD-546 : W7/W17
SY-001 BOARD (1/2)
CP201
CAMERA MODULE (1/9)
Q103 17 BUFFER
Q101
CN201 (1/2)
16
CCD OUT
CH-168 BOARD
6
86
134 136 2 4 6 9 12 15 18 21 24 27 30 32
19
IC101
CCD IMAGER
Q102
23 25 24
19
RG, H1B, H2B
4 10
7
30 28
H1A, H2A
9
31 29
V2, V4, V5A, V5B,
6
4 V6, V7A, V7B, V8 W7/W17 34
8 W5/W15
i
V2, V4, V5A, V5B, 30 V7, V8, V9, V10 i
10
28
12 i 15
26 i
W5/W15 W7/W17 23
11 33
V1A, V1B, V3A, V3B
V1, VST, 36 V3B, V3A 35
57
33
66 11
75
W5/ W7/ 26 W15 W17
VHLD
V6
32
VST
VHLD
27 31
VSUB
21
27
VSUB CONT 20
POWER SAVE
37
5 2 4
1 3
9 12 i 18
7 8 10 11
20
19
21
Q201
36
49
133
105
66
33 IC101 101
42
120
51
CCD SIGNAL PROCESSOR,
99
37 TIMING 132
48 GENERATOR 124
113 109
84
112 115
125 119
118 121
10 13
126 i
17
129
20
3
7
123
11
19
135
22
i
CA AD00 CA AD13
35
45
CA HD
46
CA FD
48
MCK TG
38
XCS FE, XCS TG
39
W5/W15
47
54MHz CLKTGO
X201
67.5MHz W7/W17
40 41
SAN1 SO, XSAN1 SCK
42
XSAN RST OUT
Q202
VSUB CONT
F MOTOR A, A, B, B
CN401
24 i
FOCUS A, A, B, B
27
IC401
LENS DRIVE
(3/9)
A6 B5 A4 B4
FOCUS MOTOR DRIVER
B7 B8 C7 C8
FC BRK A, FC DIR A, FC DIR B
Z DC MOTOR ±
17 i
20
ZOOM DC ±
C1 D2
ZOOM MOTOR DRIVER
B3 B1 A2
ZM BRK A, ZM BRK B, ZM DIR A
IRIS M±, S±
5 i
8
IRIS M±, S±
G5 H6 G4 H4
IRIS MOTOR DRIVER
G3 H2 G2 G1
IRIS M IN, IRIS M EN, IRIS S IN, IRIS S EN
SHUTTER ±
1 i
4
SHUTTER±
E7 D7
SHUTTER MOTOR DRIVER
F8 F7
MSHUT DIR, MSHUT EN
F PI SENS OUT 29 Z PI SENS OUT 21 Z BOX1 PI SENS Col, Z BOX2 PI SENS Col 10
13
LENS TEMP 31
FC SENS ZM SENS 1ST ZM DC FG 1A, 1B
LENS TEMP
XE_H
A : VIDEO SIGNAL A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL
DSC-W5/W7/W15/W17
FLASH UNIT
TRIG 300V
XE_L
C901 CHARGING + CAPACITOR
CHARGE+ CHARGE-
05
D851
T851
5
4
1
3
Q851
3-1
ST UNREG
1
IC851
8
7
2 TRANS DRIVE,
FLASH CONTROL,
FLASH CHARGE
DETECT
4
6
(9/9)
5
STRB CHG XSTRB FULL
STRB ON STRB CHG CONT
K5 G4 H4 L5 H2 H1 J1 J2 M5 J4 K4 M6
K2 K1
H5
D8 D7 E8 E7 D6 D5 E6 B4
E9 B8 D9
W25
J5
F2
U22 Y25
IC301
E1
(1/2)
CAMERA DSP, CPU LENS CONTROL, MODE CONTROL (2/9)
LCD D0 LCD D7
LCD HD, LCD VD, LCD CK
XCS PANEL XSAN RST OUT
SAN1 SO, XSAN1 SCK
B3 A3
K2
B4 B5 A5 B6
K3
A7 B7
K1
A9 C9
IC601
J6
A2 LCD DRIVE
(6/9)
B10
B1 K4 C2
C10
D2 J4 D1
B9 A10
E2 F2 F1 G2 G1 H2
CN601 R4 G5 B3
CS, COM 23 24
RGT, PSIG, 2
HCK1, HCK2, REF, HST, PCG, XSTBY, DWN, EN, VCK, VST
6i 8 1i1
14
1i9
22
CN752 (1/2)
CN451 (1/2)
8 BL H 8 7 BL L 7
CN452 BL H 1 BL L 3
SW-001 BOARD (1/2)
PANEL UNIT
LCD901 COLOR
LCD MONITOR
D901 BACKLIGHT
AF4
XSAN RST OUT
U2 R6
SAN1 SO, XSAN1 SCK
BL L BL H
SAN1 SO, XSAN1 SCK
R23
H26
SAN VOUT
U23
VIDEO AMP ON
IC802
4 VIDEO AMP 2 1 (7/9)
V LINE OUT
K26
L4
L26
L2
T23
N5
Y26
SAN AUOUT SAN AUIN
XAUDIO MUTE XCS AUDIO
N2 P5
AC1 AD1
N6
T5
P4
N4
AB6 AC4
P6
AE4 AE5
R2
AC5 AF6
R25 R5
AB13 AA13 AE13 AF13 AF12 AE12 AA12 AC12 AC11 AB12 AE11 AF11
AE10 AB11 AC10 AB10
AF21 AF20 AE20 AB18 AB19 AC19 AB16 U4 AE19 AF19 AF18 AE18 AA15 AC18 AC17 V4 AB15 AE17 AF17 AE16 AB14 AC16 AC15 AE14
V5 W4
J25
AC6
AE6 AF9
USB DPULLUP
USB DP, USB DM Q301
DPULLUP ON
MS BS, MS D0 MS D3, MS CLK XSAN RST OUT CPU D0 CPU D15 CPU A01 CPU A21, CPU A25
CPU A20, A21, A25 CPU D0 CPU D15 CPU A01 CPU A21 CPU D0 CPU D15
XCPU CS4 K10
F4 K3 J3 G3 H7 H9 G6 G9 F7 E8 D10 D9 H8 H10 G8 G10
IC381 E7 E9 D7 E10
32M AND FLASH (5/9)
XCPU CS0 SAN 27M CLKO
E8 D8 C8 B8 A8 B7 A7 F7 E6 E5 G5 B5 C7 A2 B2 C2 A1 B1 C1 E4 G3 E3 G1 D2 D1 D4
B6 A6 C6 B3 G7 F6 F5 F4
D5 F3 F2 E2
IC351
32M BURST FLASH (4/9)
E7
B4
1
OVERALL (2/2) (PAGE 3-4)
2
OVERALL (2/2) (PAGE 3-3)
D21 D22 D20 B22 A22 A23
B23 E20 E21 B24 A24 A25
B25 C25 C26 B26 E10 A10
D10 E11 B10 A11 B11 E12
R22
D11 D12 F12 B12 A12 E13 D13 D14 F13 B15 F14 E14
V23
D17 D18 D16 B18 A19
B19 E16 D19 E19 E17
B20 A20 B21 A21
R4
A18
AB22
A17
DSP DQ00 DSP DQ31, DSP DQM0 DSP DQM3
DSP AQ00 DSP AQ11, DSP QBA0, DSP QBA1 DSP QCLK DSP QCLKE
R8 N7 R9 N8 P9 M8 M7 L8 L2 M3 M2 P1 N2 R1 N3 R2 E8 D7 D8 B9 C8 A9 C7 A8 A2 C3 A1 C2 B1 D2 D3 E2 K9 K1 F8 F2
G8 G9 F7 F3 G1 G2 G3 H1 H2 J3
G7 H9 J7 H8
IC353
J1
256M SDRAM
J2
(4/9)
3-2
3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SY-001 BOARD (2/2)
V LINE OUT
OVERALL (1/2) (PAGE 3-2)
2
SAN AUOUT SAN AUIN
SAN1 SO, XSAN1 SCK XAUDIO MUTE XCS AUDIO
USB DP, USB DM DPULLUP ON
MS BS, MS D0 MS D3, MS CLK
B6
E5
IC801
E6
AUDIO AMP A5
F3
(7/9)
A2
E3
F1 E4
D1
MIC SIG
SP±
V LINE OUT AU LINE OUT
CN801 2
CN802 1 2
MIC901
SP901 SPEAKER
XAV JACK IN
J751
AV OUT (MONO)
CN751
D±
3 2
VCC 1
CN705
MS BS, DATA0 DATA3, SCLK
2i 5
7
8 INT
6
(USB)
MEMORY STICK
SW-001 BOARD (2/2)
D456 (MS ACCESS)
CN451 (2/2)
1
S456 458, 454, 460
FUNCTION KEY
5
S451 453, 455, 459
FUNCTION KEY
6
CN752 (2/2)
1 XACCESS LED
D703 (AE/AF LOCK)
D702 FLASH/ RECORDING
5 KEY AD0 6 KEY AD1
CONTROL SWITCH BLOCK
S001 (SHUTTER)
MODE DIAL
D001 (POWER)
S002 POWER
05
CN753
9
XAE LOCK ON XSHTR ON
8
7 MODE DIAL0, 1 10
5 XPWR LED
1 XPWR ON
DSC-W5/W7/W15/W17 3-3
X301 12MHz
A6
U25 XAV JACK IN
XMS IN B10 USB VBUS C9
A4
XAE LOCK LED F22
XSTRB LED XACCESS LED
IC301
E22
(2/2)
FRONT CONTROL (2/9)
E4
KEY AD0 K23 KEY AD1 L23
X001 32.768kHz
PANEL 8.5V EVER 3.0V MS VCCV D 3.1V A 3.1V CAM 2.9V D 1.8V
CAM 7.5V/8.0V CAM 15V M 5V D 1.2V
A9
A8
IC001
DC/DC CONVERTER
(8/9)
CAM 0.5V
W7/W17
B8
XAE LOCK SW XSHUTTER SW
N21
P23
MODE DIAL0, 1 L22 L25
D23
H1
K25
BATT SENS
G5
T25
MS PWR ON
D3
W23
XCS DD
A6
AA5
C6
AB5
SAN0 SI, SAN0 SO, XSAN0 SCK
C5
Y5
B6
R26
XDD RST OUT
A7
Y4
E9
AA23
XPWR OFF
B7
F9
XPWR ON C7
XAF LED
ST UNREG
BT701 LITHIUM BATTERY
BL H
1
BL L
OVERALL (1/2)
(PAGE 3-2)
3-4
CN201 (2/2)
CD-545/546 FLEXIBLE BOARD (2/2)
CD-545 : W5/W15 CD-546 : W7/W17
39 XAF LED
D104 SELF TIMER/ AF ILLUMINATOR
CN001
1 i
BATT UNREG
7
10 BATT GND i
–
16
BT901 BATTERY TERMINAL
A : VIDEO SIGNAL A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL
3-3. POWER BLOCK DIAGRAM ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SY-001 BOARD
F001
BT901
BATTERY
TERMINAL
CN001
1
i
7
BATT UNREG
F002
–
10 BATT GND i
16
BT701 LITHIUM BATTERY
VL 3V
D001
ST UNREG
L851
J1 UNREG1-1 K1 UNREG1-2 J6 UNREG2-1 K6 UNREG2-2
A1 PWR1-1 B1 PWR1-2 C2 PWR1-3 D10 PWR2
B8 RTCBAT
H1 LDO1
UNREG
LX3 E10
VO3 E9 VL3 F9
L005 D002
F003 SUFFIX: -12, -22 SUFFIX: -11, -21
VO7 K4
VO1-1 F1 VO1-2 F2 VFB1 H2
LDO2IN B3 LDO2 A3
IC851
TRANS DRIVE, FLASH CONTROL, FLASH CHARGE DETECT
(9/9)
T851
FLASH UNIT
M 5V
BL H BL L PANEL 8.5V D 3.1V
D 1.8V
L001
A 3.1V
LDO3IN B2 LDO3 A2
L003 LX2 C10 VFB2 D8
IC001 DC/DC CONVERTER (8/9)
PWR56OUT1 J7 PWR56OUT2 K7
LX5-1 J9 LX5-2 J10 LX5-3 K9 LX5-4 K10
D003 VO5 H10 VFB5 H9
IC002
DC CONTROL (8/9)
4 IN 3 IN+
OUT 1
Q005 DC CONTROL
Q004 SWITCHING
4 VEE REG2 3 STB 6
2 VCC REG1 1
IC003 REG (8/9)
CAM 2.9V D 1.2V
CAM 0.5V
W7/W17
CAM 7.5V/8.0V CAM 15V
EVER 3.0V L006
GT6 H6 VFB6 H7
D3 MS PWR ON MS PWR IN G1 MS PWR G2
L010
MS VCC
IC301 T25 K25
FRONT W23 CONTROL
(2/9) AA5 AB5 Y5
R26 Y4 AA23
P25 E5
MS PWR ON BATT SENS
XCS DD
SAN0 SI, SAN0 SO, XSAN0 SCK XDD RST OUT XPWR OFF 7.5V ON XFC RST LED
L302
L301
G5 UNREGMON A6 CE C6 SO C5 SI B6 SCLK A7 XRESET
B7 XPWROFF
AU 3.1V D 1.2V
A 3.1V D 3.1V
SD 3.1V VI 3.1V
BG4 G9
TG4 F10 PSG4 G8 VFB4 F7
05
DSC-W5/W7/W15/W17 3-5
L008 Q001 DC CONTROL
Q002, 003 SWITCHING
M 5V
IC801 AUDIO AMP
(7/9)
AU 3.1V
1 Vout Vdd 4 A 3.1V
IC804 2.8V REG
(7/9)
D 1.2V
A 3.1V D 3.1V
SD 3.1V VI 3.1V
D 1.2V A 3.1V D 3.1V SD 3.1V D 3.1V
L351
M 5V CAM 2.9V
PANEL 8.5V
L603 L601 L604
L602
CN752 BL H 8 BL L 7
D 3.1V 2
IC601
LCD DRIVE (6/9)
CN601 18 VDD
SW-001 BOARD
CN451
8
BL H
7
BL L
CN452 1 BL H 3 BL L
D456
2
(MS ACCESS)
PANEL UNIT
LCD901
COLOR LCD
MONITOR
D901 BACKLIGHT
IC351 32M BURST
FLASH (4/9)
IC381 32M AND FLASH
(5/9)
IC353 256M SDRAM
(4/9)
L802
A 3.1V M 5V
IC802 VIDEO AMP
(7/9)
D702 FLASH/ RECORDING
D703 (AE/AF LOCK)
CONTROL SWITCH BLOCK
CN753
D 3.1V
4
D 3.1V
3
D 3.1V
D001 (POWER)
CAM 2.9V
W7/W17
CAM 0.5V
CP201 CAMERA MODULE
(1/9)
CH-168 BOARD
L204 53
L203
54
55
71
L202
52
57
L205
56
FB204
49
FB203
51
50
IC101
CCD SIGNAL PROCESSOR,
TIMING GENERATOR
W5/W15
CAM 15V CAM 7.5V8.0V
D 3.1V MS VCC
CD-545/546 FLEXIBLE BOARD
CD-545 : W5/W15
CD-546 : W7/W17
L201CN201 13
CAM 15V
FB205
1
1
IC101 CCD IMAGER
38 D 3.1V
D104 SELF TIMER/ AF ILLUMINATOR
IC401
LENS DRIVE (3/9)
CN705 VCC 9
1 CAM 7.5V : W5/W15 CAM 8.0V : W7/W17
MEMORY STICK
D 3.1V
Q401
XFC RST LED D 3.1V
CN401 28 F PI SENS Vcc
LENS BLOCK
FZOOCOUMS SENSOR
23 Z PI SENS Vcc
Z BOX2 PI 14 SENS Vcc 9 Z BOX1 PI
SENS Vcc
ZOOM SENSOR
ZOOM FG
3-6E
4-1. FRAME SCHEMATIC DIAGRAM
1
2
3
4
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
5
6
7
8
9
10
11
12
13
14
15
16
A
CONTROL
BT901 BATTERY TERMINAL
SWITCH BLOCK
B
CN001 16P BATT_GND 16 BATT_GND 15 BATT_GND 14 BATT_GND 13 BATT_GND 12 BATT_GND
11 BATT_GND 10 NC 9 NC 8
BATT_UNREG 7 BATT_UNREG 6 BATT_UNREG 5 BATT_UNREG 4 BATT_UNREG 3 BATT_UNREG 2
BATT_UNREG 1 CN753 10P MODE_DIAL1 10 XAE_LOCK_ON 9
XSHTR_ON 8 MODE_DIAL0 7
REG_GND 6 XPWR_LED 5
D_3.1V 4 D_3.1V 3
N.C. 2 XPWR_ON 1
C
D
MIC901 MIC
CN801 2P 1 MIC_GND 2 MIC_SIG
E
CN451 8P
CN752 8P
BL_H 8
8 BL_H
BL_L 7
7 BL_L
KEY_AD1 6
FFC-051
6 KEY_AD1
KEY_AD0 5 N.C 4
REG_GND 3
FLEXIBLE FLAT CABLE
5 KEY_AD0 4 N.C. 3 REG_GND
F
D_3.1V 2
2 D_3.1V
XACCESS_LED 1
1 XACCESS_LED
SW-001
BOARD
G
(CONTROL SWITCH)
H
CN705 10P 1 VSS 2 MS_BS 3 DATA1 4 SDIO/DATA0 5 DATA2 6 INT 7 DATA3 8 SCLK 9 VCC 10 VSS
PANEL UNIT
CN601 24P
24 COM
23 CS
I
D901
22 VST 21 VCK
BACKLIGHT
20 EN 19 DWN
18 VDD
17 VSS
16 N.C.
LCD901
15 VSSG
14 XSTBY
J
2.5 INCH
13 PCG
12 HST
COLOR
11 REF 10 TEST1
LCD MONITOR
9 N.C. 8 HCK2
7 HCK1
6 PSIG
K
5G
4R
3B
2 RGT
1 TEST2
FLASH UNIT
C901
CHARGING CAPACITOR
SY-001 BOARD
(1/9) (CAMERA MODULE) (2/9) (CAMERA DSP, CPU) (3/9) (LENS DRIVE) (4/9) (BURST
FLASH, SDRAM) (5/9) (AND FLASH) (6/9) (LCD DRIVE) (7/9) (AUDIO, VIDEO) (8/9)
(DC/DC CONVERTER) (9/9) (FLASH DRIVE, CONNECTOR)
MEMORY STICK
MEMORY STICK
CP201
CH-168 BOARD
CCD SIGNAL PROCESS
BT701 LITHIUM BATTERY
J751 AV OUT (MONO)
3 1 2
4
CN751 5P 5 GND 4 ID 3 D+ 2 D1 VCC
Note: Pin name A/B of CN201
A : W5/W15 B : W7/W17
CN201 39P XAF_LED 39
D_3.1V 38
GND 37
V1A/V1 36
V1B/VST 35
V2 34
V3A/V3B 33
V3B/V3A 32
VST/VHLD 31
V4 30
V5A 29
V5B 28
VHLD/V6 27
V6/V7 26
V7A/V8 25
V7B/V9 24
V8/V10 23
GND 22
VSUB 21
VSUB_CONT 20
POWER_SAVE 19
CCD_GND 18
NC 17
CCD_OUT 16
GND 15
GND 14
CAM_15V 13
GND 12
GND 11
H1B 10
H1A 9
GND 8
H2B 7
H2A 6
GND 5
RG 4
GND 3
GND 2
CAM_-7.5V/-8.0V 1
CN401 31P LENS_TEMP 31
GND 30 F_PI_SENS_OUT 29 F_PI_SENS_VCC 28
F_MOTOR_B 27
F_MOTOR_A 26
F_MOTOR_B 25
F_MOTOR_A 24
Z_PI_SENS_VCC 23
GND (Z_PI_SENS) 22
Z_PI_SENS_OUT 21 Z_DCMOTER- 20
Z_DCMOTER- 19 Z_DCMOTER+ 18 Z_DCMOTER+ 17
GND (Z_BOX2) 16
Z_BOX2_PI_SENS_OUT 15
Z_BOX2_PI_SENS_VCC 14
Z_BOX2_PI_SENS_Col 13
Z_BOX1_PI_SENS_OUT 12
GND (Z_BOX1) 11
Z_BOX1_PI_SENS_Col 10
Z_BOX1_PI_SENS_Vcc 9
IRISM- 8
IRISM+ 7 IRISS- 6 IRISS+ 5 SHUTTER_- 4
(USB)
SHUTTER- 3 SHUTTER+ 2
SHUTTER_+ 1
CN452 6P 6 N.C. 5 N.C. 4 N.C. 3 BL_L 2 N.C. 1 BL_H CN802 2P 1 SP+ 2 SP-
L
05
DSC-W5/W7/W15/W17
4-1
SP901 SPEAKER
W5/W15
CD-545 FLEXIBLE
BOARD
(CCD IMAGER)
W7/W17
CD-546 FLEXIBLE
BOARD
(CCD IMAGER)
LENS FLEXIBLE
4-2
LENS BLOCK OVF
CCD
FRAME
4-2. SCHEMATIC DIAGRAMS
Link
CD-545 FLEXIBLE BOARD: W5/W15 (CCD IMAGER)
CD-546 FLEXIBLE BOARD: W7/W17 (CCD IMAGER)
SW-001 BOARD (CONTROL SWITCH) CONTROL SWITCH BLCOK
COMMON NOTE FOR SCHEMATIC DIAGRAMS
DSC-W5/W7/W15/W17
4-2. SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary
note is printed in each block)
(For schematic diagrams)
Link · All capacitors are in µF unless otherwise noted. pF : µ µF. 50 V or less are not indicated except for electrolytics
and tantalums.
· Chip resistors are 1/10 W unless otherwise noted.
k=1000 , M=1000 k.
· Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
· Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
Kinds of capacitor Case Size External dimensions (mm)
· Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
· Parts with differ according to the model/destination.
Refer to the mount table for each function.
· All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.
· Signal name
XEDIT EDIT
PB/XREC PB/REC
· 2: non flammable resistor · 5: fusible resistor
· C: panel designation
· A: B+ Line
· B: B Line
· J : IN/OUT direction of (+,-) B LINE.
· C: adjustment for repair.
· A: not use circuit
· Circled numbers refer to waveforms. (Measuring conditions voltage and waveform)
· Voltages and waveforms are measured between the
measurement points and ground when camera shoots
color bar chart of pattern box. They are reference values
and reference waveforms.
(VOM of DC 10 M input impedance is used)
· Voltage values change depending upon input
impedance of VOM used.)
1. Connection
Pattern box Pattern box
Color bar chart
Pattern box PTB-450 J-6082-200-A or Small pattern box PTB-1450 J-6082-557-A
For PTB-450: J-6020-250-A
For PTB-1450: J-6082-559-A
L = About 28 cm(PTB-450) L = About 12 cm(PTB-1450)
L Front of the lens
2. Adjust the distance so that the output waveform of Fig. a and the Fig. b
can be obtain.
H
Yellow Cyan Green White Magenta Red Blue
B
B
A
A=B/2
A
Fig. a (Video output terminal output waveform)
Electronic beam scanning frame
CRT picture frame
Fig.b (Picture on monitor TV)
When indicating parts by reference number, please include the board name.
Note :
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Note :
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie.
DSC-W5/W7/W15/W17 4-5
For Schematic Diagram · Refer to page 4-37 for printed wiring board.
1
2
3
4
5
6
7
8
CD-545 FLEXIBLE BOARD: W5/W15
A CCD IMAGER (5M CCD BLOCK)
XX MARK:NO MOUNT
LND101 39
XAF_LED
B
LND102 38 LND103 37
D_3.1V GND
LND104 36
V1A
LND105 35
V1B
LND106 34
V2
LND107 33
V3A
LND108 32
V3B
LND109 31
VST
LND110 30
V4
C
LND111 29
V5A
LND112 28
V5B
LND113 27
VHLD
LND114 26
V6
LND115 25
V7A
LND116 24
V7B
LND117 23
V8
LND118 22
GND
D
LND119 21
VSUB
SY-001 (1/9)
CN201
PAGE 4-13 of LEVEL3
LND120 20 LND121 19 LND122 18 LND123 17
VSUB_CONT POWER_SAVE
CCD_GND NC
LND124 16
CCD_OUT
LND125 15
GND
LND126 14
GND
E
LND127 13
CAM_15V
LND128 12
GND
LND129 11
GND
LND130 10
H1B
LND131 9
H1A
LND132 8
GND
LND133 7
H2B
F
LND134 6 LND135 5
H2A GND
LND136 4
RG
LND137 3
GND
LND138 2
GND
LND139 1 CAM_-7.5V
D104 OPY5052
SELF TIMER/ AF ILLUMINATOR
R101 82
C101 XX
Q101 DTC144EMT2L
SWITCH
R102 22k
R103 3900
Q103 2SC4250(T5LSONY1)
BUFFER
R109 0
C103 XX
C107 0.1u 16V
VOUT NC GND GND GND VDD RG H2B H1B SUB CSUB NC VL H1A H2A NC
NC V8 V7B V7A V6 VHLD V5B V5A V4 VST V3B V3A V2 V1B NC V1A
Note: CD-545 flexible complete board and IC101 are not supplied, but there are
included in CCD block assy.
Note: Voltage and Waveform of mounted on CD-545 flexible board can not be
measured, because they are mounted by the side of the lens.
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
IC101
CCD IMAGER IC101
ICX455CQZ-13 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
G
05
DSC-W5/W7/W15/W17
4-7
Q102 DTC144EMT2L
SWITCH
R104 820
C104 0.1u 16V
R105 3900
C102
0.1u 16V
C105 0.1u
16V
Precautions for Replacement of CCD Imager · The CD-545 flexible board mounted
as a repair part is not
equipped with a CCD imager. When replacing this board, remove the CCD imager
from the old one and mount it onto the new one. · If the CCD imager has been
replaced, carry out all the adjustments for the camera section. · As the CCD
imager may be damaged by static electricity from its structure, handle it
carefully like for the MOS IC. In addition, ensure that the receiver is not
covered with dusts nor exposed to strong light.
4-8
CD-545
For Schematic Diagram · Refer to page 4-38 for printed wiring board.
1
2
3
4
5
6
7
8
CD-546 FLEXIBLE BOARD: W7/W17
A CCD IMAGER (7M CCD BLOCK)
XX MARK:NO MOUNT
Note: CD-546 flexible complete board and IC101 are not supplied, but there are
included in CCD block assy.
Note: Voltage and Waveform of mounted on CD-546 flexible board can not be
measured, because they are mounted by the side of the lens.
LND101 39
XAF_LED
B
LND102 38 LND103 37
D_3.1V GND
LND104 36
V1
LND105 35
VST
LND106 34
V2
LND107 33
V3B
LND108 32
V3A
LND109 31
VHLD
LND110 30
V4
C
LND111 29
V5A
LND112 28
V5B
LND113 27
V6
LND114 26
V7
LND115 25
V8
LND116 24
V9
LND117 23
V10
LND118 22
GND
D
LND119 21
VSUB
SY-001 (1/9)
CN201
PAGE 4-13 of LEVEL3
LND120 20 VSUB_CONT
LND121 19 POWER_SAVE
LND122 18
CCD_GND
LND123 17
NC
LND124 16
CCD_OUT
LND125 15
GND
LND126 14
GND
E
LND127 13
CAM_15V
LND128 12
GND
LND129 11
GND
LND130 10
H1B
LND131 9
H1A
LND132 8
GND
LND133 7
H2B
F
LND134 6 LND135 5
H2A GND
LND136 4
RG
LND137 3
GND
LND138 2
GND
LND139 1 CAM_-8.0V
D104 OPY5052
SELF TIMER/ AF ILLUMINATOR
R101 33
C101 XX
Q101 DTC144EMT2L
SWITCH
R102 12k
R103 2700
Q103 2SC4250(T5LSONY1)
BUFFER
R109 0
C103 XX
NC V10
V9 V8 V7 V6 V5B V5A V4 V3B V3A VHLD V2 VST NC V1
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
IC101
CCD IMAGER IC101
ICX489CQZ-13
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
C107 0.1u 16V
VOUT NC GND GND GND VDD RG H2B H1B SUB CSUB H1A H2A VL GND NC
G
05
DSC-W5/W7/W15/W17
Q102 DTC144EMT2L
SWITCH
R104 1200
C104 XX 16V
R105 1500
C102
0.1u 16V
C105 0.1u
16V
Precautions for Replacement of CCD Imager · The CD-546 flexible board mounted
as a repair part is not
equipped with a CCD imager. When replacing this board, remove the CCD imager
from the old one and mount it onto the new one. · If the CCD imager has been
replaced, carry out all the adjustments for the camera section. · As the CCD
imager may be damaged by static electricity from its structure, handle it
carefully like for the MOS IC. In addition, ensure that the receiver is not
covered with dusts nor exposed to strong light.
4-9
4-10
CD-546
Schematic diagrams of the CH-168 and SY-001 boards are not shown. Pages from
4-11 to 4-30 are not shown.
DSC-W5/W7/W15/W17
For Schematic Diagram · Refer to page 4-44 for printed wiring board.
1
2
3
4
5
SW-001 BOARD
A CONTROL SWITCH
XX MARK:NO MOUNT
S455 T
(ZOOM)
S459 W
21
B
21
R456 2200
43
R455 2200
S451 DISPLAY/ LCD ON/OFF
21
43
43
C
D
E
05
21
43 S452 MENU
R451 2200
21
43 S453
IMAGE SIZE/ DELETE
R452 2200
R454 2200 21 43 S454 (REVIEW)
R453 2200
S456
21
(SELF TIMER) 4 3
21 43 S457 (SET)
R457 2200 21
43 S460
(MACRO) R458 2200
21
43 S458
(FLASH)
D451 MAZS068008SO
D452 MAZS068008SO
D455 XX
D453 XX
LND452 STATIC_GND LND451 STATIC_GND
CN452 6P 6 N.C. 5 N.C. 4 N.C. 3 BL_L 2 N.C. 1 BL_H
R459 1k
D456 SML-310LTT86 (MS ACCESS)
CN451 8P 8 BL_H 7 BL_L 6 KEY_AD1 5 KEY_AD0 4 N.C. 3 REG_GND 2 D_3.1V 1 XACCESS_LED
6
D901 BACKLIGHT
SY-001 (8/9)
CN752 THROUGH THE FFC-051 FLEXIBLE
FLAT CABLE PAGE 4-28 of LEVEL3
1
2
3
4
CONTROL SWITCH BLOCK
A CONTROL SWITCH BLOCK is replaced as block, so that PRINTED WIRING BOARD is
omitted.
R007 6800
R009 4700
R010 3300
B
R004 22k
11 Beach 10 Snow
9 Candle
8
Twilight portrait
R012 2200
12 Landscape
7 Twilight
6 MANUAL
5 P_AUTO
R014 22k
C
1
Soft snap
2 MOVIE 3 PLAY
4 AUTO
R013 6800
R006 2200
R008 3300
R011 4700
S001 (SHUTTER)
(1st)
D
(2nd)
3
1
42
S002 POWER
R016
E
20k
R015 20k
D001 TLYU1002(TPX1,SONY)
(POWER)
F
10 MODE_DIAL1 9 XAE_LOCK_ON 8 XSHTR_ON 7 MODE_DIAL0 6 REG_GND 5 XPWR_LED 4 D_3.1V 3 D_3.1V 2 N.C. 1 XPWR_ON
LND010 LND009 LND008 LND007 LND006 LND005 LND004 LND003 LND002 LND001
DSC-W5/W7/W15/W17
4-31
G
05
SY-001 (9/9)
CN753 PAGE 4-29 of LEVEL3
4-32
SW-001, CONTROL SWITCH BLOCK
4-3. PRINTED WIRING BOARDS
Link
CD-545 FLEXIBLE BOARD: W5/W15 CD-546 FLEXIBLE BOARD: W7/W17
SW-001 BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS MOUNTED PARTS LOCATION CIRCUIT BOARDS LOCATION
Board Name
CD-545 FLEXIBLE CD-546 FLEXIBLE SW-001
Function
CCD IMAGER CCD IMAGER CONTROL SWITCH
DSC-W5/W7/W15/W17
4-3. PRINTED WIRING BOARDS
4-3. PRINTED WIRING BOARDS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
·
: Uses unleaded solder.
·
: Circuit board
: Flexible board
Pattern from the side which enables seeing.
: pattern of the rear side
(The other layers’ patterns are not indicated)
· Through hole is omitted.
· Circled numbers refer to waveforms.
· There are a few cases that the part printed on diagram
isn’t mounted in this model.
· C: panel designation
· Chip parts.
Transistor
Diode
C
654 456 5 4 4 5
3
3
3 123
BE
123 321 123 321 1 22 13 2
2 1 2 1 2 1 654 4 3 3 4 654 456
543 345 4 1
1 2 2 1 123 321 32
41
Board Name
CD-545 flexible CD-546 flexible SW-001
Parts Location (Shown on Page)
4-47 4-47 4-49
Pattern
Total Number of Layers
Layers Not Indicated
2 layers
2 layers
2 layers
DSC-W5/W7/W15/W17
4-35
CD-545 FLEXIBLE: W5/W15
Note for Printed Wiring Board (See page 4-35). : Uses unleaded solder.
CD-545 FLEXIBLE BOARD
D104 SELF TIMER/ AF ILLUMINATOR
A
5M
D104
Note: CD-545 flexible complete board and IC101 are not supplied, but there are
included in CCD block assy.
B
CD-545 1-865-829>PI<
A
16 15 14
32 1
IC101
C
Q103 E C B C103
17 18 19
30 31 32
Q101 BC E R109 C102
R103 C101 R102 R101
C104
C107
C105
R104
BC E
R105
D
Q102
E
LND102 LND104 LND106 LND108 LND110 LND112 LND114 LND116 LND118 LND120 LND122 LND124 LND126 LND128 LND130 LND132 LND134 LND136 LND138
LND101 LND103 LND105 LND107 LND109 LND111 LND113 LND115 LND117 LND119 LND121 LND123 LND125 LND127 LND129 LND131 LND133 LND135 LND137 LND139
39
1
05
1
DSC-W5/W7/W15/W17
1-865-829- 11
2
4-37
CD-546 FLEXIBLE: W7/W17
Note for Printed Wiring Board (See page 4-35). : Uses unleaded solder.
CD-546 FLEXIBLE BOARD
D104 SELF TIMER/ AF ILLUMINATOR
A
7M
D104
Note: CD-546 flexible complete board and IC101 are not supplied, but there are
included in CCD block assy.
B
CD-546 1-865-830>PI<
A
16 15 14
32
1
IC101
C
Q103 E C B C103
17 18 19
30 31 32
Q101 BC E R109 C102
R103
C101
R102 R101
C104
C107
C105
R104
R105 BCE
D
Q102
E
LND102 LND104 LND106 LND108 LND110 LND112 LND114 LND116 LND118 LND120 LND122 LND124 LND126 LND128 LND130 LND132 LND134 LND136 LND138
LND101 LND103 LND105 LND107 LND109 LND111 LND113 LND115 LND117 LND119 LND121 LND123 LND125 LND127 LND129 LND131 LND133 LND135 LND137 LND139
39
1
05
1
1-865-830- 11
2
4-38
CD-545, CD-546
Printed wiring boards of the CH-168 and SW-001 boards are not shown. Pages
from 4-39 to 4-42 are not shown.
DSC-W5/W7/W15/W17
DSC-W5/W7/W15/W17
4-43
SW-001
Note for Printed Wiring Board (See page 4-35). : Uses unleaded solder.
SW-001 BOARD
1
3
1
3
S459
S455
A
2
4
2
4
S459
S455
R456 W (ZOOM) T
6
S451
DISPLAY/ LCD ON/OFF
1
CN452
1
3
S451
8
CN451
D452 D453
2
4
B
S452 R451
MENU
R452 R455
LND451
1
R459
1
3
S452
2
4
S458
(FLASH)
1
3
S458
R453
C
S454
2
(REVIEW)
S460
4
S457
(MACRO)
1
3
1
3 (SET)1
3
S454
S457
S460
2
4
2
4
2
4
S453 1
IMAGE SIZE/ DELETE
D4
2 R454
2
S453
3
1
LND452
05
1
3 S456
R458
S456
(SELF TIMER)
4
D456 (MS ACCESS)
R457
K
D456
D455 D451
A
1-865-828- 11 21
2
4-44
SW-001
Waveforms of the SW-001 board are not shown. Pages 4-45 and 4-46 are not
shown.
DSC-W5/W7/W15/W17
4-3. PRINTED WIRING BOARDS
4-5. MOUNTED PARTS LOCATION
CD-545 FLEXIBLE BOARD
C101 C-1 C102 C-1 C103 C-1 C104 D-2 C105 D-2 C107 D-2
D104 A-1
IC101 C-2
Q101 D-1 Q102 D-1 Q103 C-1
R101 D-1 R102 D-1 R103 C-1 R104 D-2 R105 D-2 R109 C-1
CD-546 FLEXIBLE BOARD
C101 C-1 C102 C-1 C103 C-1 C104 D-2 C105 D-2 C107 D-2
D104 A-1
IC101 C-2
Q101 D-1 Q102 D-1 Q103 C-1
R101 D-1 R102 D-1 R103 C-1 R104 D-2 R105 D-2 R109 C-1
no mark : side A * mark : side B
DSC-W5/W7/W15/W17
4-47
CD-545, CD-546
Mounted parts location of the SY-001 board is not shown. Pages 4-48 is not
shown.
DSC-W5/W7/W15/W17
SW-001 BOARD
CN451 B-2 CN452 A-2
D451 D-2 D452 B-1 D453 B-2 D455 D-2 D456 D-2
R451 B-1 R452 B-1 R453 C-1 R454 D-1 R455 B-1 R456 A-1 R457 D-2 R458 D-2 R459
C-2
S451 B-1 S452 B-1 S453 D-1 S454 C-1 S455 A-2 S456 D-1 S457 C-1 S458 C-1 S459
A-1 S460 C-2
4-3. PRINTED WIRING BOARDS
no mark : side A * mark : side B
DSC-W5/W7/W15/W17
4-49E
SW-001
NOTE
5. REPAIR PARTS LIST
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
Link
EXPLODED VIEWS
A
OVERALL ASSEMBLY
B
CABINET (FRONT) BLOCK
C
MAIN BLOCK ASSEMBLY
D
LENS BLOCK ASSEMBLY
Link
ELECTRICAL PARTS LIST
ACCESSORIES
CD-545 FLEXIBLE BOARD D CD-546 FLEXIBLE BOARD D SW-001 BOARD
A
DSC-W5/W7/W15/W17
5. REPAIR PARTS LIST
5. REPAIR PARTS LIST
NOTE: · -XX, -X mean standardized parts, so they may have some differences
from
the original one. · Items marked “*” are not stocked since they are seldom
required for routine
service. Some delay should be anticipated when ordering these items. · The
mechanical parts with no reference number in the exploded views are not
supplied. · Due to standardization, replacements in the parts list may be
different from
the parts specified in the diagrams or the components used on the set. ·
CAPACITORS:
uF: µF · COILS
uH: µH · RESISTORS
All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal
Oxide-film resistor F: nonflammable · SEMICONDUCTORS In each case, u: µ, for
example: uA…: µA… , uPA… , µPA… , uPB… , µPB… , µPC… , µPC… , uPD…, µPD… ·
Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model
CH : Chinese model CND : Canadian model HK : Hong Kong model J : Jpanese model
JE : Tourist model KR : Korean model
When indicating parts by reference number, please include the board name.
The components identified by mark 0 or dotted line with mark 0 are critical
for safety. Replace only with part number specified.
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne
les remplacer que par une pièce portant le numéro spécifié.
DSC-W5/W7/W15/W17 5-1
5-1. EXPLODED VIEWS
5-1-1. OVERALL ASSEMBLY
ns: not supplied
1
5. REPAIR PARTS LIST
Ver 1.2 2005.09
4
3
5
LCD901
Main block assembly (See page 5-4.)
ns
2
7
9
ns
Cabinet (front) block (See page 5-3.)
4 6
8
D901
7
7
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
Ref. No.
1 1 1 1 1
Part No.
Description
1-479-037-11 SWITCH BLOCK, CONTROL (SILVER) (W5) 1-479-037-21 SWITCH BLOCK, CONTROL (SILVER) (W7) 1-479-037-31 SWITCH BLOCK, CONTROL (BLACK) (W15) 1-479-037-41 SWITCH BLOCK, CONTROL (BLACK) (W7) 1-479-037-51 SWITCH BLOCK, CONTROL (BLACK) (W17)
1
1-479-037-61 SWITCH BLOCK, CONTROL (BLACK) (W5)
02
2-348-199-01 GUARD, TERMINAL
3
A-1096-987-A SW-001 BOARD, COMPLETE
4
3-078-889-11 SCREW (M1.7)
5
2-348-202-01 BLIND SHEET
6
2-348-201-01 FRAME, LCD
Ref. No.
7 7 8
Part No.
Description
2-515-756-21 SCREW (M1.7), TORASUTA, P2 (SILVER) 2-515-756-71 SCREW (M1.7), TORASUTA, P2 (BLACK) A-1095-193-A CABINET (REAR) BLOCK ASSY (W5: SILVER)
8 8 9 9 D901
A-1095-276-A CABINET (REAR) BLOCK ASSY (BLACK) A-1095-278-A CABINET (REAR) BLOCK ASSY (W7: SILVER) 2-580-522-01 CABINET, BT SIDE (C) (SILVER) 2-580-522-11 CABINET, BT SIDE (C) (BLACK) 1-479-015-11 BLOCK, LIGHT GUIDE PLATE (2.5)
LCD901 8-753-229-36 ACX336AK-3
DSC-W5/W7/W15/W17 5-2
5. REPAIR PARTS LIST
5-1-2. CABINET (FRONT) BLOCK
55
54
56
53
52
MIC901
57
58 60
59 61
SP901
62 63
66
67
64 65
51
Ref. No.
51 51 52 52 52
Part No.
Description
2-348-157-01 RING, LENS (W5/W7: SILVER/W15) 2-348-157-11 RING, LENS (W7: BLACK/W17) 2-348-158-01 GRIP (40) (W5: SILVER) 2-348-158-11 GRIP (40) (W5: BLACK/W15) 2-348-293-01 GRIP (50) (W7/W17)
53
2-515-716-01 SHEET, GRIP ADHESIVE
54
3-348-998-51 SCREW (M1.4X3.5), TAPPING, PAN
55
2-348-156-01 CABINET (FRONT) (W5: SILVER)
55
2-348-156-11 CABINET (FRONT) (BLACK)
55
2-348-156-21 CABINET (FRONT) (W7: SILVER)
56
2-348-161-01 WINDOW, AF
57
2-348-166-01 CUSHION, MICROPHONE
58
2-348-185-01 CUSHION, MICROPHONE (B)
59
2-348-198-01 COVER, MIC
60
2-108-698-01 SCREW (M1.4)
DSC-W5/W7/W15/W17
Ref. No.
61 62 62 63 64
Part No.
Description
2-348-163-01 SCREW, TRIPOD X-2024-644-1 BOTTOM ASSY (40), CABINET (SILVER) X-2025-148-1 BOTTOM ASSY (B (40)), CABINET (BLACK) 2-348-160-01 INNER HOLDER (FRONT) 2-348-164-01 SHEET (OVF), ADHESIVE
65
2-348-162-01 WINDOW, OVF (SILVER)
65
2-348-162-11 WINDOW, OVF (BLACK)
66
2-515-756-21 SCREW (M1.7), TORASUTA, P2 (SILVER)
66
2-515-756-71 SCREW (M1.7), TORASUTA, P2 (BLACK)
67
2-348-159-01 RING (40), ORNAMENTAL (W5/W15)
67
2-348-294-01 RING (50), ORNAMENTAL (SILVER) (W7)
67
2-348-294-11 RING (50), ORNAMENTAL (BLACK) (W7/W17)
MIC901 1-542-600-11 MICROPHONE UNIT
SP901 1-825-923-21 LOUDSPEAKER (1.3CM)
5-3
5. REPAIR PARTS LIST
5-1-3. MAIN BLOCK ASSEMBLY
ns: not supplied
103
BT901
102
SY-001
104
ns (Note)
!
101
(including CP201 (CH-168 board) and BT701)
Lens block assembly (See page 5-5.)
BT701
! BT701(BATTERY, LITHIUM SECONDARY) Board on the mount position (See page 4-40).
105
C901
Note: Included in SY-001 board (suffix: -11).
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type.
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
Ref. No. 101 101 101 101 101
101 101 101
Part No.
Description
A-1096-995-A SY-001 BOARD, COMPLETE (SERVICE) (GP1) (W5: J)
A-1096-996-A SY-001 BOARD, COMPLETE (SERVICE) (GP2) (W5: US, CND, AUS/W15:
AUS)
A-1096-997-A SY-001 BOARD, COMPLETE (SERVICE) (GP1) (W7: J)
A-1096-998-A SY-001 BOARD, COMPLETE (SERVICE) (GP2) (W7: US, CND, AUS/W17:
AUS)
A-1097-361-A SY-001 BOARD, COMPLETE (SERVICE) (GP3) (W5: AEP, UK/W15: AEP, UK)
A-1097-362-A SY-001 BOARD, COMPLETE (SERVICE) (GP4) (W5: AR, BR, E/W15: E)
A-1097-363-A SY-001 BOARD, COMPLETE (SERVICE) (GP5) (W5: CH, HK, KR, JE/W15:
CH, HK, KR, JE)
A-1097-364-A SY-001 BOARD, COMPLETE (SERVICE) (GP3) (W7: AEP, UK/W17: AEP, UK)
Ref. No. 101
101
0 102 103 104
0 105 0 105 0 BT701 0 BT901
0 BT901
0 BT901
0 C901
Part No.
Description
A-1097-365-A SY-001 BOARD, COMPLETE (SERVICE) (GP4) (W7: AR, BR, E/W17: E)
A-1097-366-A SY-001 BOARD, COMPLETE (SERVICE) (GP5) (W7: CH, HK, KR, JE/W17:
HK, KR, JE)
1-479-039-11 FLASH UNIT 1-963-591-11 CABLE, FLEXIBLE FLAT (FFC-051)
2-348-515-01 LABEL, FUSE REPLACEMENT CAUTION
X-2024-645-1 HOLDER ASSY (40), JACK (SILVER) X-2025-151-1 HOLDER ASSY (B
(40)), JACK (BLACK) 1-528-999-61 BATTERY, LITHIUM SECONDARY 1-756-527-11
HOLDER, BATTERY (WITH TERMINAL)
(W5: SILVER) 1-756-527-21 HOLDER, BATTERY (WITH TERMINAL) (BLACK)
1-756-527-31 HOLDER, BATTERY (WITH TERMINAL)
(W7: SILVER)
1-112-169-11 CAP, ELECT
135uF
DSC-W5/W7/W15/W17 5-4
5. REPAIR PARTS LIST
5-1-4. LENS BLOCK ASSEMBLY
151
153
(Note 1)
154
(Note 1)
152
(Note 1)
161
(including CD-545/546 flexible board and IC101) (Note 2)
160 158
157 156 155
159 162
Note 1: Be sure to read “2-3. Exchange Method of Barrier Assy” on page 2-5
when change Ref. No. 152, 153 and 154.
Note 2: Be sure to read “Precuations for Replacement of CCD Imager” on page
4-8 or 4-10 when changing the CCD imager.
Ref. No.
151 152 153 154 155
156 156 157 158
Part No.
Description
A-1105-719-A LENS BLOCK ASSY (890C (J1)) 3-091-427-01 RING (A), ORNAMENTAL (Note 1) 3-086-156-31 SCREW, TAPPING (P2) (Note 1) X-3954-476-1 BARRIER ASSY (Note 1) 2-021-317-01 MASK, LPF
1-788-104-11 OPTICAL FILTER BLOCK (W5/W15) 1-788-176-11 OPTICAL FILTERBLOCK (OFB-02-21) (W7/W17) 2-021-318-01 SEALGOM 890 2-348-196-01 HOLDER, AF
Ref. No. 159 160 161
161
162
Part No.
Description
3-080-222-01 SCREW (M1.7), TAPPING, P2 3-348-998-61 SCREW (M1.4X4), TAPPING,
PAN A-1087-313-A CCD BLOCK ASSY
(including CD-545 flexible board and IC101 (CCD IMAGER)) (W5/W15) (Note 2)
A-1087-314-A CCD BLOCK ASSY (including CD-546 flexible board and IC101 (CCD
IMAGER)) (W7/W17) (Note 2)
X-2024-646-1 FRAME ASSY, LENS
DSC-W5/W7/W15/W17 5-5
CD-545 CD-546
5-2. ELECTRICAL PARTS LIST
Ref. No. Part No.
Description
Ref. No. Part No.
Description
A-1087-313-A CCD BLOCK ASSY (W5/W15) (Not supplied) CD-545 FLEXIBLE BOARD,
COMPLETE
*** (CCD block assy is including CD-545 flexible
board and IC101 (CCD
imager).)
R103 1-218-958-11 RES-CHIP
2.7K
R104 1-218-954-11 RES-CHIP
1.2K
R105 1-218-955-11 RES-CHIP
1.5K
R109 1-218-990-11 SHORT CHIP 0
5% 1/16W 5% 1/16W 5% 1/16W
< CAPACITOR >C102 C104 C105 C107
1-107-826-11 CERAMIC CHIP 1-107-826-11 CERAMIC CHIP 1-107-826-11 CERAMIC CHIP 1-107-826-11 CERAMIC CHIP
0.1uF 0.1uF 0.1uF 0.1uF
10% 16V 10% 16V 10% 16V 10% 16V
Electrical parts list of the CH-168 board is not shown. Page 5-7 is not shown.
< DIODE >D104 6-500-505-01 DIODE OPY5052 (SELF TIMER/AF ILLUMINATOR)
< IC >IC101 (Not supplied) CCD IMAGER (Note)
< TRANSISTOR >Q101 Q102 Q103
6-550-119-01 TRANSISTOR 6-550-119-01 TRANSISTOR 8-729-050-22 TRANSISTOR
DTC144EMT2L DTC144EMT2L 2SC4250 (T5LSONY1)
< RESISTOR >R101 R102 R103 R104 R105
1-218-940-11 RES-CHIP 1-218-969-11 RES-CHIP 1-218-960-11 RES-CHIP 1-218-952-11 RES-CHIP 1-218-960-11 RES-CHIP
82
5% 1/16W
22K
5% 1/16W
3.9K
5% 1/16W
820
5% 1/16W
3.9K
5% 1/16W
R109 1-218-990-11 SHORT CHIP 0
A-1087-314-A CCD BLOCK ASSY (W7/W17) (Not supplied) CD-546 FLEXIBLE BOARD,
COMPLETE
*** (CCD block assy is including CD-546 flexible
board and IC101 (CCD
imager).)
C102 C105 C107
1-107-826-11 CERAMIC CHIP 0.1uF 1-107-826-11 CERAMIC CHIP 0.1uF 1-107-826-11 CERAMIC CHIP 0.1uF
10% 16V 10% 16V 10% 16V
< DIODE >D104 6-500-505-01 DIODE OPY5052 (SELF TIMER/AF ILLUMINATOR)
< IC >IC101 (Not supplied) CCD IMAGER (Note)
< TRANSISTOR >Q101 Q102 Q103
6-550-119-01 TRANSISTOR 6-550-119-01 TRANSISTOR 8-729-050-22 TRANSISTOR
DTC144EMT2L DTC144EMT2L 2SC4250 (T5LSONY1)
< RESISTOR >R101 1-218-935-11 RES-CHIP R102 1-218-966-11 RES-CHIP
DSC-W5/W7/W15/W17
33
5% 1/16W
12K
5% 1/16W
5-6
Note: Be sure to read “Precautions for Replacement of CCD Imager” on page 4-8 or 4-10 when changing the CCD imager.
SW-001
5-2. ELECTRICAL PARTS LIST
Ref. No. Part No.
Description
A-1096-987-A SW-001 BOARD, COMPLETE ***
< CONNECTOR >CN451 1-817-549-11 CONNECTOR, FPC (LIF (NON-ZIF)) 8P CN452 1-816-654-31 FFC/FPC CONNECTOR (LIF) 6P
< DIODE >D451 D452 D456
8-719-056-54 DIODE MAZS068008SO 8-719-056-54 DIODE MAZS068008SO 8-719-064-07 DIODE SML-310LTT86 (MS ACCESS)
< RESISTOR >R451 1-216-825-11 METAL CHIP 2.2K R452 1-216-825-11 METAL CHIP 2.2K R453 1-216-825-11 METAL CHIP 2.2K R454 1-216-825-11 METAL CHIP 2.2K R455 1-216-825-11 METAL CHIP 2.2K
5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W
R456 1-216-825-11 METAL CHIP 2.2K R457 1-216-825-11 METAL CHIP 2.2K R458 1-216-825-11 METAL CHIP 2.2K R459 1-216-821-11 METAL CHIP 1K
5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W
< SWITCH >S451 S452 S453 S454 S455
1-786-157-11 SWITCH, TACTILE (DISPLAY / LCD ON/OFF) 1-786-157-11 SWITCH, TACTILE (MENU) 1-786-157-11 SWITCH, TACTILE (IMAGE SIZE/DELETE) 1-786-157-11 SWITCH, TACTILE (g(REVIEW)) 1-786-157-11 SWITCH, TACTILE (T(ZOOM))
S456 S457 S458 S459 S460
1-786-157-11 SWITCH, TACTILE (F(SELF TIMER)) 1-786-157-11 SWITCH, TACTILE (a(SET)) 1-786-157-11 SWITCH, TACTILE (f(FLASH)) 1-786-157-11 SWITCH, TACTILE (W(ZOOM)) 1-786-157-11 SWITCH, TACTILE (G(MACRO))
Ref. No. Part No.
Description
Electrical parts list of the SY-001 board is not shown. Pages 5-9 to 5-12 are not shown.
DSC-W5/W7/W15/W17 5-8
Ver. 1.5 2007.09
The changed portions from Ver. 1.4 are shown in blue.
Checking supplied accessories.
Note: This item is supplied with the unit as an accessory, but is not prepared
as a service part.
Battery charger (BC-CS2A/CS2B) (1) 0 1-477-814-41 (US, CND, JE, J) 0 1-477-814-51 (AEP, UK, E, AR, HK, AUS) 0 1-477-814-61 (KR, CH)
Battery case (1) 3-074-757-01
Power cord (1) 0 1-823-946-12 (AEP, E) 0 1-782-476-51 (CH) 0 1-783-374-11 (UK, HK) 0 1-783-952-21 (AR) 0 1-790-107-42 (US, CND) 0 1-790-732-12 (JE, J) 0 1-776-985-12 (KR) 0 1-827-945-11 (AUS)
HR6 (size AA) Ni-MH batteries (2) (Note)
Wrist strap (1) 2-050-981-01 (Silver) 2-050-981-11 (Black)
A/V connecting cable (1) 1-824-519-11
USB cable (1) 1-827-038-11
Other accessories
2-586-553-01 INSTRUCTION (READ THIS FIRST) (JAPANESE) (J) 2-586-553-11
INSTRUCTION (READ THIS FIRST) (ENGLISH)
(EXCEPT AR, KR, CH, J) 2-586-553-21 INSTRUCTION (READ THIS FIRST) (FRENCH,
ITALIAN)
(AEP, CND) 2-586-553-31 INSTRUCTION (READ THIS FIRST) (SPANISH,
PORTUGUESE) (AEP, E, AR, JE) 2-586-553-41 INSTRUCTION (READ THIS FIRST)
(GERMAN, DUTCH)
(AEP)
2-586-553-51 INSTRUCTION (READ THIS FIRST) (TRADITIONAL CHINESE, SIMPLIFIED
CHINESE) (E, HK, CH, JE)
2-586-553-61 INSTRUCTION (READ THIS FIRST) (RUSSIAN, SWEDISH) (AEP)
2-586-553-71 INSTRUCTION (READ THIS FIRST) (ARABIC, PERSIAN) (E)
2-586-553-81 INSTRUCTION (READ THIS FIRST) (KOREAN) (KR, JE) 2-586-553-91
INSTRUCTION (READ THIS FIRST) (POLISH, CZECH)
(AEP)
Conversion 2P adaptor (1) 0 1-569-008-21 (E)
Conversion 2P adaptor (1) 0 1-569-007-12 (JE)
2-586-555-11 INSTRUCTION (READ THIS FIRST) (HUNGARIAN, SLOVAK) (AEP)
2-586-561-01 INSTRUCTION (USER’S GUIDE) (JAPANESE) (J) 2-586-561-11
INSTRUCTION (USER’S GUIDE) (ENGLISH) (EXCEPT AR,
KR, CH, J) 2-586-561-21 INSTRUCTION (USER’S GUIDE) (FRENCH, ITALIAN) (AEP,
CND) 2-586-561-31 INSTRUCTION (USER’S GUIDE) (SPANISH,
PORTUGUESE) (AEP, E, AR, JE)
Soft carrying case (W15/W17 only) (1) 2-055-904-01
CD-ROM (Cyber-shot application software) (1) 2-583-852-31 (US, J) 2-583-853-01 (EXCEPT US, J)
2-586-561-41 INSTRUCTION (USER’S GUIDE) (GERMAN, DUTCH) (AEP)
2-586-561-51 INSTRUCTION (USER’S GUIDE) (TRADITIONAL CHINESE, SIMPLIFIED
CHINESE) (E, HK, CH, JE)
2-586-561-61 INSTRUCTION (USER’S GUIDE) (RUSSIAN, SWEDISH) (AEP)
2-586-561-71 INSTRUCTION (USER’S GUIDE) (ARABIC, PERSIAN) (E) 2-586-561-81
INSTRUCTION (USER’S GUIDE) (KOREAN) (KR, JE)
2-586-561-91 INSTRUCTION (USER’S GUIDE) (POLISH, CZECH) (AEP) 2-586-563-11
INSTRUCTION (USER`S GUIDE) (HUNGARIAN, SLOVAK)
(AEP)
The components identified by mark 0 or dotted line with mark 0 are critical
for safety.
Replace only with part num-
ber specified.
Les composants identifiés par une marque 0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
DSC-W5/W7/W15/W17
55–193EE
DSC-W5/W7/W15/W17
SERVICE MANUAL
Ver 1.1 2005.07
2 LEVEL
DSC-W5/W7
US Model Canadian Model Argentine Model Brazilian Model Japanese Model
DSC-W5/W7/W15/W17
AEP Model UK Model E Model
Australian Model Hong Kong Model
Korea Model Tourist Model
DSC-W5/W7/W15
Chinese Model
SUPPLEMENT-1
File this supplement with the service manual. (PV05-033)
· Precaution on Replacing the SY-001 Board
1. SERVICE NOTE
1-7. PRECAUTION ON REPLACING THE SY-001 BOARD
When you replace to the repairing board, the written data of repairing board
also might be changed to original setting. When the data has changed because
of board replaceing etc, check the data setting (VIDEO OUT Default Data, Exif
Model Data) is right. If not, rewrite to the right value.
VIDEO OUT Default Data
Page
4F 4F
Address
8D A2
Data
NTSC
PAL
00
01
00
01
Exif Model Data
Page
8F 8F
Address
E5 E6
DSC-W5 35 00
Data
DSC-W7 DSC-W15
37
31
00
35
DSC-W17 31 37
Writing Method: 1) Select page: 00, address: 01 and set data: 01. 2) Select page: 4F, address: 8D and A2, and set the VIDEO OUT Dafault Data. 3) Select page: 8F, address: E5 and E6, and set the Exif Model Data. 4) Click [Save] on the SEUS screen. 5) Wait for more than 3 sec. 6) Select page: 80, address: 30, and check that the data is “00”. 7) Select page: 00, address: 01, and set data: 00.
DSC-W5/W7/W15/W17 9-876-856-81
Sony EMCS Co.
2005G0500-1
© 2005.7 Published by DI Technical Support Department
DSC-W5/W7/W15/W17
SERVICE MANUAL
Ver 1.3 2005.12
2 LEVEL
DSC-W5/W7
US Model Canadian Model Argentine Model Brazilian Model Japanese Model
DSC-W5/W7/W15/W17
AEP Model UK Model E Model
Australian Model Hong Kong Model
Korea Model Tourist Model
DSC-W5/W7/W15
Chinese Model
SUPPLEMENT-2
File this supplement with the service manual. (PV05-071)
· Addition of SERVICE NOTE
· SY-001 BOARD TYPE CHECK (DSC-W7/W17)
DSC-W5/W7/W15/W17 9-876-856-83
Sony EMCS Co.
2005L0500-1
© 2005.12 Published by DI Technical Support Department
1. SERVICE NOTE 1-8. SY-001 BOARD TYPE CHECK (DSC-W7/W17)
The SY-001 board type can be discriminated with the mounted parts. Note: When
the data has changed because of board replacing etc., check the data setting
is right. If not, rewrite to the right value. Checking Method: 1) Refer to
“SECTION 2 DISASSEMBLY” to remove the SY-001 board. 2) Referring the following
figure, each type is discriminated with the mounted parts on the SY-001 board.
SY-001 BOARD (SIDE B)
X201
Mount : Former Type No Mount: New Type
· Differences of mounted parts on the SY-001 board
Ref. No. R238 R305 R306 R309 R349 X201
Former Type XX XX 0 XX 0
67.5MHz
New Type 0 0 XX 0 XX XX
· Differences of data
Page
Address
7D
E2
Former Type New Type
00
FF
Writing Method: 1) Select page: 00, address: 01 and set data: 01. 2) Select page: 7D, address: E2, and set data: 00 (Former type) or data: FF (New type). 3) Click [Save] on the SEUS screen. 4) Wait for more than 3 sec. 5) Select page: 80, address: 30, and check that the data is “00”. 6) Select page: 00, address: 01, and set data: 00.
DSC-W5/W7/W15/W17
— 2 —
DSC-W5/W7/W15/W17
SERVICE MANUAL
Ver. 1.4 2007.04
2 LEVEL
DSC-W5/W7
US Model Canadian Model Argentine Model Brazilian Model Japanese Model
DSC-W5/W7/W15/W17
AEP Model UK Model E Model
Australian Model Hong Kong Model
Korea Model Tourist Model
DSC-W5/W7/W15
Chinese Model
SUPPLEMENT-3
File this supplement with the service manual. (DI06-187)
· Addition of Language Group Table
5. REPAIR PARTS LIST
· Language that can be selected about SY-001 board
Area Japanese English French German Spanish Italian Portugal Simplified Chinese Traditional Chinese Arabic Dutch Russian Swedish Korean
GP1 J
z
US
GP2
CND AUS
zz zz
z
Vietnam
GP3
AEP UK
zzzzzz
E
GP4
AR BR
TW
z
z zz
JE
GP5
HK CH
KR
z
z zz
z zzz
zz
z
z
· Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korean model
DSC-W5/W7/W15/W17 9-876-856-84
Sony EMCS Co.
2007D0500-1
© 2007.4 Published by Kohda TEC
DSC-W5/W7/W15/W17
SERVICE MANUAL
Ver. 1.5 2007.09
2 LEVEL
DSC-W5/W7
US Model Canadian Model Argentine Model Brazilian Model Japanese Model
DSC-W5/W7/W15/W17
AEP Model UK Model E Model
Australian Model Hong Kong Model
Korea Model Tourist Model
DSC-W5/W7/W15
Chinese Model
SUPPLEMENT-4
File this supplement with the service manual. (DI07-147)
· Change of Board’s Suffix No. · Change of Repair Parts · Revision of
Accessories
Note: Please refer to Ver.1.5 of SERVICE MANUAL (9-876-856-31) for the
revision of accessories.
· Suffix No. of CD-545 flexible board and CD-546 flexible board have been
changed from 11 into 12 . About suffix No. 11 and 12 , there are no changes of
schematic diagram and printed wiring board.
: Points changed portion.
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
D451 MAZS068008SO
D452 MAZS068008SO
D455 XX
D453 XX D451 XX D452 XX D455 XX D453 XX
4-2. SCHEMATIC DIAGRAMS
SW-001 BOARD (CONTROL SWITCH) (Service manual page 4-31, Location B-3 to D-5)
Former
S459 W
21 43
21 R) 4 3
LND452 STATIC_GND LND451 STATIC_GND
CN452 6P 6 N.C. 5 N.C. 4 N.C. 3 BL_L 2 N.C. 1 BL_H
S459 W
21 43
21 R) 4 3
New
LND452 STATIC_GND LND451 STATIC_GND
CN452 6P 6 N.C. 5 N.C. 4 N.C. 3 BL_L 2 N.C. 1 BL_H
R457 2200
DSC-W5/W7/W15/W17_L2 9-876-856-87
R457 2200
Sony EMCS Co.
2007I0500-1
© 2007.9 Published by Kohda TEC
! : Points deleted portion.
5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS
Page
Former
New
Ref. No. Part No.
Description
Ref. No. Part No.
Description
1
1-479-037-11 SWITCH BLOCK, CONTROL (SILVER) (W5)
1
1-479-037-13 SWITCH BLOCK, CONTROL (SILVER) (W5)
1
1-479-037-21 SWITCH BLOCK, CONTROL (SILVER) (W7)
1
1-479-037-23 SWITCH BLOCK, CONTROL (SILVER) (W7)
1
1-479-037-31 SWITCH BLOCK, CONTROL (BLACK)
1
1-479-037-33 SWITCH BLOCK, CONTROL (BLACK)
5-2
1
(W15) 1-479-037-41 SWITCH BLOCK, CONTROL (BLACK) (W7)
1
(W15) 1-479-037-43 SWITCH BLOCK, CONTROL (BLACK) (W7)
1
1-479-037-51 SWITCH BLOCK, CONTROL (BLACK)
1
1-479-037-53 SWITCH BLOCK, CONTROL (BLACK)
(W17)
(W17)
1
1-479-037-61 SWITCH BLOCK, CONTROL (BLACK) (W5)
1
1-479-037-63 SWITCH BLOCK, CONTROL (BLACK) (W5)
55 54 53 52
55
%
54
53
52
5-3
51
66 67
58
MIC901
59
57 60
66
67 51
%
58
MIC901
59
% 57 60
63
63
53 2-515-716-01 SHEET, GRIP ADHESIVE 57 2-348-166-01 CUSHION, MICROPHONE 58 2-348-185-01 CUSHION, MICROPHONE (B)
DSC-W5/W7/W15/W17_L2
— 2 —
Page
Former
Ref. No. Part No.
Description
101 A-1096-995-A SY-001 BOARD, COMPLETE (SERVICE) (GP1) (W5: J)
101 A-1096-996-A SY-001 BOARD, COMPLETE (SERVICE) (GP2) (W5: US, CND, AUS/W15:
AUS)
101 A-1096-997-A SY-001 BOARD, COMPLETE (SERVICE) (GP1) (W7: J)
101 A-1096-998-A SY-001 BOARD, COMPLETE (SERVICE) (GP2) (W7: US, CND, AUS/W17:
AUS)
101 A-1097-361-A SY-001 BOARD, COMPLETE (SERVICE) (GP3) (W5: AEP, UK/W15: AEP,
UK)
New
Ref. No. Part No.
Description
101 A-1096-995-C SY-001 BOARD, COMPLETE (SERVICE) (GP1)(W5: J)
101 A-1096-996-C SY-001 BOARD, COMPLETE (SERVICE) (GP2) (W5: US, CND, AUS/W15:
AUS)
101 A-1096-997-C SY-001 BOARD, COMPLETE (SERVICE) (GP1) (W7: J)
101 A-1096-998-C SY-001 BOARD, COMPLETE (SERVICE) (GP2) (W7: US, CND, AUS/W17:
AUS)
101 A-1097-361-C SY-001 BOARD, COMPLETE (SERVICE) (GP3) (W5: AEP, UK/W15: AEP,
UK)
101 A-1097-362-A SY-001 BOARD, COMPLETE (SERVICE)
101 A-1097-362-C SY-001 BOARD, COMPLETE (SERVICE)
5-4
(GP4) (W5: AR, BR, E/W15: E)
(GP4) (W5: AR, BR, E/W15: E)
101 A-1097-363-A SY-001 BOARD, COMPLETE (SERVICE)
101 A-1097-363-C SY-001 BOARD, COMPLETE (SERVICE)
(GP5) (W5: CH, HK, KR, JE/
(GP5) (W5: CH, HK, KR, JE/
W15: CH, HK, KR, JE)
W15: CH, HK, KR, JE)
101 A-1097-364-A SY-001 BOARD, COMPLETE (SERVICE)
101 A-1097-364-C SY-001 BOARD, COMPLETE (SERVICE)
(GP3) (W7: AEP, UK/W17: AEP, UK)
(GP3) (W7: AEP, UK/W17: AEP, UK)
101 A-1097-365-A SY-001 BOARD, COMPLETE (SERVICE)
101 A-1097-365-C SY-001 BOARD, COMPLETE (SERVICE)
(GP4) (W7: AR, BR, E/W17: E)
(GP4) (W7: AR, BR, E/W17: E)
101 A-1097-366-A SY-001 BOARD, COMPLETE (SERVICE)
101 A-1097-366-C SY-001 BOARD, COMPLETE (SERVICE)
(GP5) (W7: CH, HK, KR, JE/
(GP5) (W7: CH, HK, KR, JE/
W17: HK, KR, JE)
W17: HK, KR, JE)
0 BT901 1-756-527-31 HOLDER, BATTERY (WITH TERMINAL)
0 BT901 1-756-534-31 BATTERY HOLDER (TERMINAL)
(W7: SILVER)
(W7: SILVER)
5-5
156 1-788-176-11 OPTICAL FILTERBLOCK (OFB-02-21)
156 1-788-306-11 OPTICAL FILTERBLOCK (OFB-02-26)
(W7/W17)
(W7/W17)
The components identified by mark 0 or dotted line with mark 0 are critical
for safety.
Replace only with part num-
ber specified.
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
5-2. ELECTRICAL PARTS LIST
Page
Former
Ref. No. Part No.
Description
A-1096-987-A SW-001 BOARD, COMPLETE ***
< CONNECTOR >CN451 1-817-549-11 CONNECTOR, FPC (LIF (NON-ZIF)) 8P CN452 1-816-654-31 FFC/FPC CONNECTOR (LIF) 6P
5-8
< DIODE >D451 8-719-056-54 DIODE MAZS068008SO D452 8-719-056-54 DIODE MAZS068008SO
< SWITCH >S454 S456 S457 S458 S460
1-786-157-11 SWITCH, TACTILE (g(REVIEW)) 1-786-157-11 SWITCH, TACTILE (F(SELF TIMER)) 1-786-157-11 SWITCH, TACTILE (a(SET)) 1-786-157-11 SWITCH, TACTILE (f(FLASH)) 1-786-157-11 SWITCH, TACTILE (G(MACRO))
New
Ref. No. Part No.
Description
A-1096-987-A SW-001 BOARD, COMPLETE ***
< CONNECTOR >- CN451 1-816-655-51 FFC/FPC CONNECTOR (LIF) 8P * CN452 1-816-654-51 FFC/FPC CONNECTOR (LIF) 6P
S454 S456 S457 S458 S460
1-771-138-21 SWITCH, KEY BOARD (g(REVIEW)) 1-771-138-21 SWITCH, KEY BOARD (F(SELF TIMER)) 1-771-138-21 SWITCH, KEY BOARD (a(SET)) 1-771-138-21 SWITCH, KEY BOARD (f(FLASH)) 1-771-138-21 SWITCH, KEY BOARD (G(MACRO))
DSC-W5/W7/W15/W17_L2
— 3 —
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]
Toolbar
Printing a text 1. Click the Print button . 2. Specify a printer, print range,
number of copies, and other op-
tions, and then click [OK].
Application of printing: To set a range to be printed within a page, select
the graphic selection tool and drag on the page to enclose a range to be
printed, and then click the Print button.
Finding a text 1. Click the Find button . 2. Enter a character string to be
found into a text box, and click
the [Find]. (Specify the find options as necessary)
Application to the Service Manual: To execute “find” from current page toward
the previous pages, select the check box “Find Backward” and then click the
“Find”.
3. Open the find dialog box again, and click the [Find Again] and you can
find the matched character strings displayed next. (Character strings entered
previously are displayed as they are in the text box.)
Application to the Service Manual: The parts on the drawing pages (block
diagrams, circuit diagrams, printed circuit boards) and parts list pages in a
text can be found using this find function. For example, find a Ref. No. of IC
on the block diagram, and click the [Find Again] continuously, so that you can
move to the Ref. No. of IC on the circuit diagram or printed circuit board
diagram successively. Note: The find function may not be applied to the
Service
Manual depending on the date of issue.
Reversing the screens displayed once · To reverse the previous screens
(operation) one by one, click
the . · To advance the reversed screens (operation) one by one, click
the .
Application to the Service Manual: This function allows you to go and back
between circuit diagram and printed circuit board diagram, and accordingly it
will be convenient for the voltage check.
Moving with link
1. Select either palm tool , zoom tool , text selection tool
, or graphic selection tool . 2. Place the pointer in the position in a text
where the link exists
(such as a button on cover and the table of contents page, or blue characters
on the removal flowchart page or drawing page), and the pointer will change to
the forefinger form . 3. Then, click the link. (You will go to the link
destination.)
Moving with bookmark: Click an item (text) on the bookmark pallet, and you can
move to the link destination. Also, clicking can display the hidden items. (To
go back to original state, click )
Zooming or rotating the screen display “Zoom in/out”
· Click the triangle button in the zoom control box to select the
display magnification. Or, you may click ing in or out.
or for zoom-
Switching a page · To move to the first page, click the .
· To move to the last page, click the . · To move to the previous page, click
the . · To move to the next page, click the .
“Rotate” · Click rotate tool
, and the page then rotates 90 degrees each.
Application to the Service Manual: The printed circuit board diagram you see now can be changed to the same direction as the set.
Reverse
Revision History
987685636.pdf
Ver.
Date
History
Contents
S.M. Rev. issued
1.0 2005.01 Official Release
—
—
1.1 2005.07 Supplement-1
· Precaution on Replacing the SY-001 Board
No
(S1 PV05-033)
1.2 2005.09 Correction-1
· Correction of Repair Parts
Yes
(C1)
S.M. correction: Page 5-2
1.3 2005.12 Supplement-2
· Addition of SERVICE NOTE
No
(S2 PV05-071)
(SY-001 BOARD TYPE CHECK (DSC-
W7/W17))
1.4 2007.04 Supplement-3
· Addition of Language Group Table
No
(S3 PV06-187)
1.5 2007.09 Supplement-4
· Change of Board’s Suffix No.
Yes
(S4 DI07-147)
· Change of Repair Parts
· Revision of Accessories
S.M. revised: Page 5-13
DSC-W5/W7/W15/W17
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>