tc electronic NY 10168 Impulse IR Loader User Guide
- June 16, 2024
- tc electronic
Table of Contents
NY 10168 Impulse IR Loader
Quick
Start Guide
IMPULSE IR LOADER
Safety Instruction
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Use only attachments/accessories specified by the manufacturer.
- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
- Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office, or your household waste collection service.
- Do not install in a confined space, such as a book case or similar unit.
- Do not place naked flame sources, such as lighted candles, on the apparatus.
Controls
- Level Knob – Adjusts the output level.
- Navigation Buttons – Move forward and backward through the list of IRs. Press both buttons simultaneously to enter/exit global EQ.
- Output
- Footswitch – Press and hold to switch between A/B MODE and BYPASS MODE. A/B MODE: Press to toggle between IR A and IR B. BYPASS MODE: Press to bypass the IR loader.
- USB – Connect to your computer for IR management and firmware updates.
- Power – Connect a 9 V / >100 mA power supply (not included).
- Input
A/B MODE
- Currently-selected IR
- Total number of IRs loaded into IMPULSE
- Name of current-selected IR file
- File location of currently-selected IR
- Input and output clipping indicators (visible in A/B and Bypass Mode)
- Displays whether IR A or B is selected
- EQ indicator shown when EQ is active
BYPASS MODE
LOAD YOUR OWN IR
Connect IMPULSE to your computer and open the official IMPULSE app to
easily import/export and organize your IRs.
Supported formats: .wav files, 16/24/32-bit fixed (PCM), and 32-bit float
Supported rates: 44.1 kHz, 48 kHz, 96 kHz
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
TC Electronic
IMPULSE IR LOADER
Responsible Party Name: Music Tribe Commercial NV Inc.
Address: 122 E. 42nd St.1, 8th Floor NY, NY 10168, United States
Email Address: legal@musictribe.com
IMPULSE IR LOADER
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by Music
Tribe can void the user’s authority to use the equipment.
Hereby, Music Tribe declares that this product is in compliance with Directive
2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/EU, Directive
2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC.
Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address: Gammel Strand 44, DK-1202 København K, Denmark
UK Representative: Music Tribe Brands UK Ltd.
Address: 6 Lloyds Avenue, Unit 4CL London EC3N 3AX, United Kingdom
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>