Hamilton Beach HMD300 Drink Mixer User Manual

Beach HMD300 Drink Mixer
User Manual

840206801

Mixer Safety

IMPORTANT: This operation manual should be reviewed with all equipment operators as part of your operator training program.
Your safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance.
Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to hazards that can kill or hurt you and others.
All safety messages will be preceded by the safety alert symbol and the word “WARNING. ” This word means:
WARNING You can be killed or seriously injured if you don’t follow instructions.
All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS
WARNING – When using electrical appliances, basic safety precautions should be followed to reduce the risk of personal injury, including the following:

• Read all instructions before using a mixer.
• Disconnect power before cleaning or servicing, and before installing or removing the agitator.
• Do not spray or submerge the mixer.
• Do not operate the mixer with a damaged or bent shaft or agitator. Contact technical service for the replacement of any damaged components.
• Do not put a spoon or other utensils in the container when mixing.
• Do not allow the agitator to hit the container sides when mixing.
• Inspect the mixer and agitator daily.
• Replace agitator(s) every 90 days.
• Do not operate any appliance with damaged wiring or after the appliance malfunctions or is damaged in any manner.

SAVE THESE INSTRUCTIONS

Parts and Features

The parts and features of your mixer are shown on this page. Become familiar with all parts and features before using the mixer.

Installation

1.  Remove the mounting bracket from the back of the mixer.

2. If mounting directly into a wall stud, drill 5/32″ pilot holes and then screw three of the screws provided through the three centered holes on the mounting bracket.
   b. If mounting into drywall, drill 1/4″ pilot holes and then insert the six drywall anchors provided into the wall. Align the six holes on the outside of the mounting bracket with the drywall anchors, and then screw six of the screws provided through the holes.

3. Place the drink mixer back onto the mounting bracket by inserting posts back into the appropriate holes on the back of the mixer and sliding the mixer down to lock into place.

4. Tighten the thumbscrew at the top of the mounting bracket to secure the mixer.

Operating the Mixer

Mixing a Drink
Cut Hazard. Do not put a spoon or other utensils in the container when mixing. Failure to follow these instructions can result in cuts.
Mixing a Drink
You must read the “Mixer Safety” section before using the mixer. For best mixing results, use the Hamilton Beach Universal Container (#110E). Do not use a paper cup. The container fits the container guide which starts the motor.

1. Plug the mixer into a grounded outlet.

2. Place the ingredients into the container basic milkshake recipe is:
   • 3 No. 24 scoops of ice cream
   • 4 ounces of very cold milk
   •1 ½ ounce of syrup

3. Select the desired speed using the two-speed selector switch.

4. Position the container into the container guide and move the cup upward to automatically turn the motor on. Set the container down onto the cup rest.
   NOTE: You may also turn the motor ON (I) and OFF (O) using the pulse switch.

5. When the drink is completely mixed, lift the container up off the cup rest and pull it down from the container guide. The motor will turn off. NOTE: Inspect agitator(s) daily. Replace agitator(s) every 90 days.

Using the Container Rest

Two-Position Container Rest The top container rest position is used when mixing with a standard container. In the top position, a standard container will fit into the container guide to lifting the ON/OFF actuator against the actuator switch, allowing the motor to run. To turn off the motor, rest a standard container on the lower, or standby, container rest position. The lower container rest position may also be used when mixing with larger containers, or for storing standard containers when the mixer is not in use.
NOTE: When the container is not positioned as described above, you may also turn the motor on using the pulse switch.

Replacing the Agitator
WARNING Cut Hazard. Disconnect power before installing or removing the agitator. Failure to do so can result in serious injury or cuts. Your mixer was shipped with an agitator installed on the spindle. NOTE: Agitators wear with use. Inspect agitators daily and replace them every 90 days.
To replace the agitator:

1. Disconnect power to the mixer.

2. To remove the agitator, loosen the screw by turning it counterclockwise with a straight-blade screwdriver.

3. To install the new agitator, turn the screw portion of the agitator clockwise into the spindle and hand-tighten it. To prevent damage to the agitator, do not use pliers to grip agitator blades while tightening or loosening. If necessary, pliers may be used to hold the shaft during removal.

4. Reconnect power to the mixer.

Removing/Installing the Container Guide, ON/OFF Actuator, and Housing Plug
WARNING  Cut Hazard. Disconnect power before installing or removing any parts. Failure to do so can result in serious injury or cuts.The container guide and ON/OFF actuator are removable for easy cleaning.
To remove the container guide and ON/OFF actuator:

1. Unplug mixer.
2. Pull the container guide straight out.
3. To remove the plastic ON/OFF actuator, press the retainer clip and slide it out of the container guide.
4. To replace, make sure the mixer is in an upright position, align the four posts on the back of the container guide with the four holes on the mixer, and press into place.
   NOTE: You may also operate the mixer without the container guide and ON/OFF actuator. Snap the included housing plug into the container guide holes after removing the container guide. Use the toggle switch to operate the mixer when using the mixer without the container guide/ON/OFF actuator.

Care and Cleaning of the Mixer

Cleaning and Sanitizing the Container, Spindle, and Agitator
Cleaning

1. Place a drop of detergent and 1 cup of water into a mixing container.
2. Position the container under the mixing spindle and mix on low speed (I) for 5 seconds. Empty the mixing container.
3. Place 1 cup of clean water into a container and repeat mix for 5 seconds to rinse.
   NOTE: Inspect agitator(s) daily. Replace agitator(s) every 90 days.

Sanitizing
For best results, use the Hamilton Beach Universal Container (#110E).

1.  Fill the container with sanitizing solution (1 tablespoon [15 ml] of household bleach per 1 gallon of water at 50°–70°F [10°–21°C]) to 3 ⁄4 full. Position the container under the mixing spindle and run on low speed (I) for 1 minute.
2. Remove the container. Empty sanitizing solution and rinse the container.
3. To dry, run the mixer on low speed (I) for 30 seconds with the empty container in place. DO NOT RINSE after sanitizing is completed.
   NOTE: If preferred, the container and agitator may be cleaned in a dishwasher.

Cleaning the Container Guide, Container Rest, and Housing
WARNING Electrical Shock Hazard. Disconnect power before cleaning. Failure to do so can result in death or electrical shock.
Cleaning the Container Guide, Container Rest, and Housing

1. Unplug mixer.

2. Remove the container guide (see page 6).

3. Wash the container guide with hot, soapy water; then rinse.

4. Clean the housing, front panel, and container rest with a damp, soapy cloth.

5. Wipe dry with a clean, soft cloth.

6. Reinstall the container guide.
   NOTE: Do not spray or submerge the mixer. Any resulting water damage will not be covered by the warranty.

7. Plug the mixer into a grounded outlet.

Care and Cleaning of the Mixer
Motor Replacement
To replace the motor, follow the steps below, or call an authorized service center.

1. Disconnect power to the mixer.

2. Loosen the three screws in the top cover (the screws will remain in the cover). Lift off the top cover.

3. Squeeze the tabs on the sides of the connector plug and pull the two plug halves apart.

4. Remove the agitator and then lift the motor assembly straight up and out of the housing. Discard the motor assembly in an environmentally acceptable manner that complies with federal, state, and local waste management regulations.
   NOTE: A Mylar insulating barrier with a top tab and an opening is slipped over the lower enclosure front screw boss. Make sure this is in place and DO NOT remove it.

5. Carefully lower the new motor assembly into the housing, guiding the spindle through the hole in the housing. Align the keyed portion on the rubber support with the slot in the top cover. Attach a new agitator as described in “Replacing the Agitator.”

6. Plug the two halves of the plug connector together, ensuring that all lead wire colors match, and tuck the connector into the back of the housing. Make sure that the side clips on the plug halves engage. NOTE: The plug will only connect together in one way.

7. Make sure that all wires are out of the way and that they cannot come in contact with the motor. Also, ensure that the Mylar insulating barrier is correctly positioned. Then lower the cover into place, making sure that the upper tab and seal of the back panel are in place below the lip of the cover. Secure the cover with the screws.

8. Reconnect power to the mixer.

Troubleshooting Guide

• Agitator is bent or worn (this can be prevented by not holding the container in your hand r allowing the agitator to hit the sides of the container). Replace agitators every 90 days. To  order replacement agitators, call Technical Service at
1-866-285-1087 or 910-693-4277.
The motor does not turn on when the container is set on the container rest| • Container is not tall enough to activate the motor switch. We recommend the Hamilton each Universal Container (#110E).
• The unit features a thermal overload protection circuit. Turn unit OFF (O). Wait 30 minutes. Follow the instructions in the section “Mixing    Drink.” If the unit does not turn on, call Technical Service.
Excessive product splash-out (some splash-out is common)| • Is the container too full?
• Is the speed set too high for ingredients?
• Is the agitator fastened tightly to the spindle?
• Is the agitator bent or worn? Replace agitators every 90 days.

Product Warranty

This Warranty supersedes all other Product Warranties
LIMITED WARRANTY
This warranty applies to products purchased and used in the U.S. and Canada. This is the only express warranty for this product and is in lieu of any other warranty or condition. This product is warranted to be free from defects in material and workmanship for a period of one (1) year from the date of original purchase.
If you have a claim under this warranty please contact our TECHNICAL SERVICES DEPARTMENT at 1-866-285-1087 or 910-693-4277. For faster service, locate the model, type, and serial numbers on your appliance.
This warranty does not cover glass, filters, wear from normal use, use not in conformity with the printed directions, or damage to the product resulting from accident, alteration, abuse, or misuse, or subjecting it to any voltage and waveform other than as specified on the rating label (for example, 120V ~ 60 Hz). This warranty extends only to the original purchaser. Keep the original sales receipt, as proof of purchase, is required to make a warranty claim or the warranty term will be based on the date of manufacture plus one (1) year.
We exclude all claims for special, incidental, and consequential damages caused by a breach of express or implied warranty. All liability is limited to the amount of the purchase price. Every implied warranty, including any statutory warranty or condition of merchantability or fitness for a particular purpose, is disclaimed except to the extent prohibited by law, in which case such warranty or condition is limited to the duration of this written warranty. This warranty gives you specific legal rights. You may have other legal rights that vary depending on where you live. Some states or provinces do not allow limitations on implied warranties or special, incidental, or consequential damages, so the foregoing limitations may not apply to you.
261 Yadkin Road
Southern Pines, NC 28387
www.commercial.hamiltonbeach.com

Technical Service
For assistance or replacement parts, call our
Technical Service number:
866-285-1087 or 910-693-4277
8:00 a.m. – 5:00 p.m. EST Monday – Friday
www.commercial.hamiltonbeach.com

References

• Commercial Foodservice Products | Hamilton Beach Commercial

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>