DREO HTF010S Smart 2 in 1 Town Fan User Manual

DREO HTF010S Smart 2 in 1 Town Fan

Thanks for Choosing DREOI
Your support means the world to us. We hope you enjoy our product as much as we did creating it.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL CAUTIONARY MARKINGS ON THE APPLIANCE AND SAFETY INSTRUCTIONS IN THE USER MANUAL BEFORE USE.

Do not cover the air inlet and outlet while in operation.

Do not use the fan near flammables and combustibles.

General Safety

1. Children shall not play with the appliance. Cleaning and maintenance shall not be performed by children without supervision.
2. Use the appliance as described in the user manual only. Any other use not recommended in the user manual may cause fire, electrical shock, or personal injury.
3. This appliance can be used by children aged above 8 years and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of this appliance in a safe way and understand the hazards involved.

Operation Safety

1. Place the appliance on a flat, dry surface before use.
2. Do not immerse in water and any other liquids.
3. Do not use the appliance until the base is installed.
4. Do not insert your fingers, pencil, and any other objects into the grilles while in operation.
5. Do not dismantle, repair, or modify. All servicing should be performed by qualified personnel.

Electricity Safety

1. Make sure that the voltage of your electricity supply is the same as that indicated on the appliance.
2. Always unplug before cleaning or leaving the appliance unused for a long period of time. Keep your hands dry when plugging / unplugging.
3. Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
4. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliance. Arrange cord away from traffic area and where it will not be tripped over.
5. WARNING: To reduce the risk of fire or electric shock, do not use this Fan with any solid-state speed control device.
6. This appliance employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows. unplug the product from the outlet. Replace the fuse as per the user servicing instructions and check the appliance. If the replacement fuse blows, a short-circuit may be present and the appliance should be discarded or returned to an authorized service facility for examination and/or repair.
7. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way, If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
8. WARNING: To reduce the risk of fire, electric shock or injury to persons, do not use replacement parts that have not been recommended by the manufacturer (e.g. parts made at home using a 3D printer).

FOR HOUSEHOLD USE ONLY READ AND SAVE
THESE INSTRUCTIONS

Gentle Reminder:

• Check the appliance regularly and refer to TROUBLESHOOTING or contact our customer support if it shows any of the following signs:
• Power cord or plug is damaged.
• Loud noise, unusual smell or excessive heat.

Specifications

KNOWING YOUR SMART 2-IN-1 TOWER FAN

Package Contents

Getting Started

Locate the back handle and softly pull it to remove the back cover.

Remove the filter from its plastic packaging.

Put the filter back in position by making sure both straps are pointing outwards.

Align the tab on the bottom of back cover with the slot on the fan, and then close the back cover.

Place the 2-in-1 tower fan on a flat, stable and clear surface, plug the 2-in-1 tower fan into the power outlet.

After plugging your 2-in-1 tower fan, the air quality sensor will warm-up for 10 seconds, if turned on during this phase, lights will cycle and the screen will show a warm-up countdown. You can still operate the 2-in-1 tower fan during this phase.

Control Panel

• Power Button
  • On/Off
  • Long press l0s to restore factory settings
• Tower Fan Mode Button
  • Switch between Normal/ Auto/Sleep/Breeze
  • Long press 3s to mute/unmute
• Purification Mode Button
  • Switch between 1-2-3-A-0 levels in Normal/ Sleep/ Auto Mode
  • Switch between 1-2-3-A levels in Breeze Mode
• Increase Button
  • Increase Tower Fan Speeds (1-12 Levels) excluding Breeze Mode
• Decrease Button
  • Decrease Tower Fan Speeds (12-1 Levels) excluding Breeze Mode
• Information Button
  • Switch between wind speed/PM2.5 data/filter life/ ambient temperature
  • Long press 5s to reset the Filter Change Reminder
• Timer Button (0-24H)
• Oscillation Button
  • 30°/60°/90°/120°
  • Long press 5S to start network setting and device pairing

LED Display

NOTE: This 2-in-1 tower fan features auto-brightness. The display adapts automatically based on the ambient lighting conditions.

Air Quality Indicator Light

Light Color
Blue| Air Quality Level
Excellent
---|---
Green| Good
Orange| Moderate
Red| Poor

CONNECTING TO YOUR SMART 2-IN-1 TOWER FAN MC710S

Before connecting the appliance to your mobile device, please scan the QR code on the left or go to the app store and search “Dreo”, then select and download the app.

Look for “MC710S” when connecting your new Smart 2-in-1 Tower Fan.
You can use the Dreo app to connect your smart 2-in-1 tower fan to Amazon Alexa or Google Assistant. Please follow the in-app instructions to set up your voice assistant.
NOTE: You must create a Dreo account to access voice assistants.

1. Launch Dreo and sign in or create account by following in-app instructions.

2. Enable Bluetooth on your mobile device and plug in your tower fan.

3. Hold the Oscillation button for 5 seconds to start WiFi connection settings.
   (Tip, The WiFi icon will keep flashing when pairing.)

4. Tap+ Add Device and select MC710S.

5. Follow in-app instructions to complete WiFi connection.

6. You’re now ready to control the appliance on your app. (Tip, To restart connection settings, hold the button again for 10 seconds.) Long press 10 seconds power button to unpair WiFi and restore factory settings.

USING YOUR SMART 2-IN-1 TOWER FAN

Working Modes
Tower Fan Mode :

• Normal Mode
  Runs at the fixed speed.

• Auto Mode
  Wind/Purifying speed adapts to the ambient temperature/ air quality.

• Sleep Mode
  (Mute Auto On)

2-in-1 Tower Fan speed decreases every 30 minutes. Speed decreases by three levels at most and will remain constant if at level 3, 2, or 1:
For level 12, 12 11 10 9
For level 11, 11 10 9 8
For level 10, 10 9 8 7
For level 9, 9 8 7 6
For level 8, 8 7 6
For level 7, 7 6 5
For level 6, 6 5 4
For level 5, 5 4 3
For level 4, 4 3
For level 3, 3
For level 2, 2
For level 1, 1

• Breeze Mode
  Gentle wind.

Purification Mode
Switch between 1-2-3-A-0 levels in Normal/Sleep/Auto Mode

****Switch between 1-2-3-A levels in Breeze Mode

****A, Speed adapts to the ambient air quality.
Q, No purifying the air.

Additional Features

• Change Oscillation Angle
  The oscillation angle can be set to 30/60/90/120 degrees.

• Timer
  When the fan is ON/OFF, touch the timer button repeatedly to set a timer from 1 to 24 hours. When the timer ends, the fan will stop/start running automatically. To cancel, set the time to O hour.
  Note: When the auto off timer is enabled, display will return to fan speed after 3 seconds.

• Mute
  Long press the mode button 3 seconds on the control panel to turn on/off button sounds.

• Memory
  If the fan is turned OFF or disconnected from power, it will operate under the previous settings (except the timer setting) when it is turned ON again.

Remote Control

Battery Replacement

1. Press the locking button to pop out the battery holder.
2. Replace with the same battery type with the ( +) side facing up.
3. Push in the holder until securely locked into place.

Note, If the indicator on the remote control doesn’t turn on any more, please consider replacing the battery.

WARNING

• INGESTION HAZARD: This product contains a button cell or coin battery
• DEATH or serious injury can occur if ingested.
• A swallowed button cell or coin battery can cause internal Chemical Burns in as little as 2 hours.
• KEEP new and used batteries OUT OF REACH of CHILDREN
• Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.
• Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.
• Even used batteries may cause severe injury or death.
• Call a local poison control center for treatment information.
• Compatible battery type: CR2025.
• Battery nominal voltage:3.0 Vdc
• Non-rechargeable batteries are not to be recharged.
• Do not force discharge, recharge, disassemble, heat above (rated temperature: 140°F) or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
• Ensure the batteries are installed correctly according to polarity (+and -) .
• Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
• Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
• Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

CLEANING AND MAINTENANCE

WARNING
Turn off the appliance and unplug before any cleaning and maintenance.
Note: Please clean the rear grille monthly.

Remove the screw on the bottom of the rear grille with a Philips screwdriver.

Push the grille inward and pull it out.

Clean the dust on blades using a vacuum cleaner or air duster. Rinse the rear grille under running water or with a clean, damp cloth.

Dry up, then install the grille and the screw back in place, making sure the bottom pegs are fully inserted into the slots.

Outer Surface
Gently wipe off the dust with a soft, dry cloth.

CAUTION

1. Always unplug the fan before any cleaning o r maintenance to avoid the risk of fire, electric shock, or injury to persons.
2. Do not immerse in water o r get water inside the motor housing.
3. Do not use any chemical agents when cleaning the fan.
4. Store in a cool, dry place and cover it to protect from dust.

Replacing the Filter
It’s recommended to replace the filter every 6-8 months or when the filter change reminder alerts.

The Filter Change Reminder will flash when the filter needs to be replaced. Turn off and unplug the 2-in-1 tower fan.
Locate the back handle and softly pull it to remove the back cover of your 2-in-1 tower fan.

Pull the old filter out from the straps. Properly dispose the old filter after removing it from the 2-in-1 tower fan.
Remove the plastic wrap of your new filter then carefully place it within the 2-in-1 tower fan. Make sure both straps are pointing outwards and the filter is within the marked guidelines before closing the back cover.

Plug in the 2-in-1 tower fan. Long press the button for 5 seconds (until hearing the beep) to reset the filter change reminder.
Note: you can also reset the filter change reminder directly from the Oreo App.

Cleaning the Inside & Outside

1. Unplug the 2-in-1 tower fan before any cleaning and maintenance.
2. Remove the filter and clean the inside with a dust vacuum.
3. Wipe clean the housing with a dry, soft, non-abrasive cloth.
4. For optimal use, the outer pre-filter can be cleaned with a soft, dry brush once every 2-4 weeks.
5. It is recommended to clean the AO sensor on the back with a dust vacuum at least every three months.

User Servicing Instructions (Fuse)

This appliance features a fused safety plug that protects against overload or short-circuit situations. If the fuse blows, please cut off power and follow the below instructions or consult a qualified electrician.

1. Grasp plug and remove from the receptacle or other outlet device.
   Do not unplug by pulling on cord.

2. Open fuse cover. Slide open fuse access cover on top of attachment plug towards blades.

3. Remove fuse carefully. Push the fuse from the other side to remove the fuse.

4. Risk of fire. Replace fuse only with 2.5 Amp.125 Volt fuse.

5. Close fuse cover. Slide closed the fuse access cover on top of attachment plug.

WARNING
Risk of fire. Do not replace attachment plug. Contains a safety device(fuse) that should not be removed. Discard product if the attachment plug is damaged.

TROUBLESHOOTING

Related to the Filter
Where can I buy a new filter?

1. Please purchase from Dreo official website, www.dreo.com.
   I changed the filter, but the Filter Change Reminder is still on.

2. The Filter Change Reminder will not automatically reset. Please press and hold the Filter Reset button to reset the reminder, the indicator will turn off after reset.

The Filter Change Reminder has not turned on for a long period of time.

1. If you dont use the purification mode of your 2-in-1 tower fan often, the reminder will take longer to light up.

Related to Use
Why is my 2-in-1 tower fan not working?

1. Check if the power is connected, the power cord is damaged, or the electrical outlet is powered.
2. Make sure that there is enough space around the 2-in-1 tower fan.
3. Check if the filter packaging has been removed.
4. Fan speed will be low when auto mode is switched on. Try to switch to higher speed.
5. Replace the filter if the filter is clogged and overloaded.

My 2-in-1 tower fan doesn’t improve the air quality.

1. Check if the filter packaging has been removed.
2. Make sure the windows are closed as polluted air may continue coming in from outside of the windows.
3. The overloaded filter will make the fan work harder to pass the air through. Consider replacing the filter if it is clogged.
4. Do not place in crowded areas and corners.
5. Check if air outlet and inlet are obstructed.
6. When utilizing the purification mode, it is advisable to close doors and windows in order to prevent the infiltration of external sources of pollution.
7. For larger rooms, it is recommended to increase the purification level.

Why is my 2-in-1 tower fan making a loud noise?

1. The higher mode will produce higher noise level as the fan is at the maximum speed to clean the air in the room more quickly.
2. Switch the 2-in-1 tower fan to sleep mode or lower fan speeds.

Why is the Air Quality indicator is always red?

1. The Air Quality sensor may need to be cleaned.
2. Ultrasonic humidifiers usually release large particles with their mist. If a humidifier is placed near the sensor. The sensor may be detecting and reporting the large particles coming from the humidifier. Avoid using both appliances at the same time, or switch the 2-in-1 tower fan to another mode besides Auto Mode.
3. The rear grille may not be cleaned in a timely manner.

The odor in the room is very strong, but the Air Quality Indicator is only green or blue.

1. The Air Quality Sensor detects PM 2.5 particles but cannot detect odors. If you feel that the indoor air odor is relatively strong, it is recommended to manually open the highest fan speed.

My fan is shaky and wobbling!

1. Please the fan on a flat, level surface.

DREO CUSTOMER CARE

Default 12-Month Warranty
This appliance is covered by Dreo warranty for 12 months from the date of its original purchase.

Extend Your Warranty
Extend your warranty by registering your new appliance on our website https://dreo.com/warranty.

The warranty will not apply in cases of:

• Accident, misuse, or repairs performed by unauthorized personnel.
• Any unit that has been tampered with or used for commercial purposes.
• Normal wear and tear of wearable parts.
• Use of force, damage caused by external inf1uences.
• Damage caused by non-observance of the User Manual, e.g. connection to an unsuitable mains supply or noncompliance with the instructions.
• Partially or completely dismantled appliances.
• Defects caused by or resulting from damages from shipping or from repairs, service, or alteration to the product or any of its parts that have been performed by a repair person not authorized by DREO.

We can only provide after-sales service for products that are sold by OREO or OREO authorized retailers and distributors. If you have purchased your unit from a different place, please contact your seller for return and warranty issues.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Please note that changes or modifications of this product is not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures,

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation

We’re Here to Help!
888-290-1688 Mon- Fri,9,00am-5,00pmPST/PDT
Website: www.dreo.com
Email:   support@dreo.com
Shenzhen Hesung Innovation Technology Co., LTD
26F, Bldg A7, Creative City, Shenzhen, China
MADE IN CHINA
www.dreo.com

Looking for help?
Contact us to get expert support.
Email: support@dreo.com
888-290-1688
Website: www.dreo.com
Mon – Fri, 9:00 am-5:00 pm PST,PDT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>