Lnicez Pool Cover Pump Instruction Manual
- June 16, 2024
- Lnicez
Table of Contents
Lnicez Pool Cover Pump
Product Information
Specifications:
- Product Name: Water Pump
- Model: SML-3200
- Material: Durable ABS plastic
- HP (Power): 1/10 (75W)
- Volts: 110V-120V
- Hz: 60Hz
- Amps : 1.8A
- Max Flow: 850GPH
- Maximum Head: 10.5ft
- Power Cord Length : 20ft
- Low Suction : 0.4”
- Min Water Temperature: 32°F (0°C)
- Max Water Temperature: 95°F (35°C)
- Waterproof Level: IPX8
- Pump Construction: Thermoplastic
- Power Source: Corded Electric
Function:
The Pool Cover Pump is a submersible pump designed for pumping water. It
can be used in in-ground pools, above-ground pools, above-ground pool covers,
and low-lying ground where water needs to be drained or removed.
Safety Instructions:
- CAUTION: Before using, please ensure that the rated voltage marked on the label is the same as the voltage you are using.
- CAUTION: Risk of electric shock. Please do not move it when it is plugged in or in working condition.
- CAUTION: Risk of electric shock. Before installing, disassembling, or cleaning the pump, please unplug it to ensure safety.
- CAUTION: Please protect the wire from sharp objects, hot surfaces, and chemicals. Before you use it, please check the power cord for any damage or wear. Do not use it if there are these signs.
- CAUTION: Please do not put the pump in water with a temperature higher than 35°C or a temperature lower than 0°C.
- CAUTION: The pump relies on water for cooling and lubrication. Do not allow the pump to run without water. It may cause damage to the internal parts of the pump and may also shorten the life of the pump.
- CAUTION: The pump’s motor has a thermostatic core that automatically cuts off power if the engine gets too hot. It is designed as a safety device and will fail after repeated use. Please let the pump cool down for about 15-20 minutes before subsequent use.
- CAUTION: Use only in liquids compatible with the pump’s material. Do not use this pump in flammable or explosive liquids like gasoline, kerosene, etc.
- CAUTION: Do not use this pump for potable/drinking water.
- CAUTION: Periodically check the inside of the pump for obstructions. Cleaning should be done when necessary. Before checking, please disconnect the power to the pump.
Structure Introduction
Serial number | Name | Function |
---|---|---|
1 | Filter cover | Filter and protect the machine body |
2 | 3/4 adapter | Get greater water flow. Compatible with the included |
drain.
3| 1/2 adapter| Water flow between adapter 1/2 and 3/4 adapter. Make the pump
work properly.
4| 3/5 adapter| Core component
5| Rotating core|
6| Machine body|
7| Buckle lid|
8| Fixed seal cover|
Frequently Asked Questions (FAQ):
-
Q: Can this pump be used for draining hot tubs?
A: Yes, as long as the water temperature is within the specified range of 0°C to 35°C. -
Q: Can this pump be used for saltwater pools?
A: Yes, the pump’s material is compatible with liquids used in saltwater pools. -
Q: How often should I clean the pump?
A: Cleaning should be done when necessary. Periodically check the inside of the pump for obstructions and clean as needed.
POOL COVER PUMP
- This manual will help you to use the pump more effectively.
- Please take a few minutes to read it carefully.
- If you need help or have any questions, please get in touch with our customer service center, email: lnicez@foxmail.com .
About Lnicez
- Lnicez specializes in designing, developing, producing, and trading a wide range of water pump items for many years. These products go through several rigorous inspection procedures. Because we are committed to providing safe and high-quality products to our customers. Moreover, we continuously strive to upgrade and optimize our products.
- We do our best to provide the best shopping experience to our customers!
Function
This submersible pump is designed for pumping water. It can be used in in-
ground pools, above-ground pools, above-ground pool covers, and low-lying
ground, where water needs to be drained or removed.
Safety Instructions
-
CAUTION: Before using, please ensure that the rated voltage marked on the label is the same as the voltage you are using.
-
CAUTION: Risk of electric shock. Please do not move it when it is plugged in or in working condition.
-
CAUTION: Risk of electric shock. Before installing, disassembling, or cleaning the pump, please unplug it to ensure safety.
-
CAUTION: Please protect the wire from sharp objects, hot surfaces, and chemicals. Before you use it, please check the power cord for any damage or wear. Do not use it if there are these signs.
-
CAUTION: Please do not put the pump in water with a temperature higher than 35℃ or a temperature lower than 0℃.
-
CAUTION: The pump relies on water for cooling and lubrication. Do not allow
the pump to run without water. It may cause damage to the internal parts of the pump and may also shorten the life of the pump. -
CAUTION: The pump’s motor has a thermostatic core that automatically cuts off power if the engine gets too hot. It is designed as a safety device and will fail after repeated use. Please let the pump cool down for about 15-20 minutes before subsequent use.
-
CAUTION: Use only in liquids compatible with the pump’s material. Do not use this pump in flammable or explosive liquids like gasoline, kerosene, etc.
-
CAUTION: Do not use this pump for potable/drinking water.
-
CAUTION: Periodically check the inside of the pump for obstructions. Cleaning should be done when necessary. Before checking, please disconnect the power to the pump.
Specification
Product Name | Water Pump |
---|---|
Model | SML-3200 |
Material | Durable ABS plastic |
HP (Power) | 1/10( 75W) |
Volts | 110V-120V |
Hz | 60Hz |
Amps | 1.8A |
Max Flow | 850GPH |
Maximum Head | 10.5ft |
Power Cord Length | 20ft |
Low Suction | 0.4’’ |
Min Water Temperature | 32℉(0℃) |
Max Water Temperature | 95℉ (35℃) |
Waterproof level | IPX8 |
Pump Construction | Thermoplastic |
Power Source | Corded Electric |
Structure Introduction
Serial number | Name | Function |
---|---|---|
1 | Filter cover | Filter and protect the machine body |
2 | 3/4″ adapter | Get greater water flow. |
3 | 1/2″ adapter | Compatible with the included drain. |
4 | 3/5″ adapter | Water flow between adapter 1/2″ and 3/4″ adapter. |
5 | Rotating core | Make the pump work properly. |
6 | Machine body | Core component |
7 | Buckle lid | Fixed seal cover |
--- | --- | --- |
8 | 20 feet power cord | Power cord for greater safety. |
9 | Water lock lid | Prevent the machine from leaking |
Installation
-
Connection adapter
Connect the 1/2” adapter if you want to use the hose we provide. We also provide you with 3/5” and 4/3” adapters. You could install the corresponding diameter of the drainage pipe by yourself. -
Connecting the drainage pipe
Secure the drain hose before plugging in the pump. A drain that is not secured may “whip” and cause personal injury or property damage. -
Place the pump on a solid surface in the water
Do not place the pump directly in mud, sand, or silt or on a rocky surface, as these materials can clog or cause damage to the pump. -
Plug the pump into the power supply
Please be sure the pump is already in the water before connecting the power.
How to disassemble and clean the pump?
-
Remove the water filter cover: You need to prepare a screwdriver and use it to pry the snap strip on the side of the pump. Then you will take out the water filter cover.
-
Remove the water leaf cover : After removing the water filter cover, you will see a black snap-on water leaf cover. Similarly, use a screwdriver to remove it.
Please be careful not to break the point on the cover when taking it off. -
Take out the pump’s rotor : After removing the water leaf cover, you will see a rotor composed of a magnet and a plastic impeller, a stainless steel shaft core, and two black silicone bushings. Please take them out separately.
-
Effective cleaning: Use detergent to assist in cleaning visible stains and impurities. Please note: The pump rotor catch and the water outlet should be washed.
-
Reinstallation : After washing, please follow the original steps to install.
1. Install the rotor. Please note that the two black silicone bushings must be aligned with the holes.
2. Install the water lobe cover and fix the location of the point.
3. Install the water filter cover.
4. Installation is complete.
Troubleshooting
Problem | Problem Causes | Corrective Action |
---|---|---|
The pump doesn’t work | Just received the pump: It may be caused by the | |
pressure difference. | We recommend that you do not use it with water pipes at |
first.
After using the pump for some time: It may be internally blocked by some
impurities.| You can disassemble the pump for cleaning. The steps for
disassembly and cleaning are in point 7.
GFCI is tripped.| Reset the GFCI
The water level is below 0.4”.| Place the pump in water with a level of 0.4”
or more.
Low flow rate of pump| Kinked and sharply bent hose.| Straighten the hose.
The hose is placed at a very high height.| Do not place the water pipe in a
high position.
| The water pipe is too long.| Choose the right length of the hose.
---|---|---
The rotor is clogged.| Clean the rotor.
Select the adapter with the smaller diameter.| Choose an adapter with
a larger diameter.
The pump runs, but little or no water is pumped out| Hose is blocked| Clean
hose
Rotor is blocked| Clean rotor
The pump components are worn, damaged, or clogged.| Check the pump components
for wear, damage, or clogging. Clean or replace it if necessary.
List
We Need Your Support
- We welcome you to post quality reviews on our product pages so that others can benefit from your experience.
- We know how valuable your time is, so we especially appreciate your time and input.
- Your support is critical to us!
Any using problems contact us, email: lnicez@foxmail.com