metabo PE 15-25 Angle Polisher Owner’s Manual Product Information
- January 15, 2024
- metabo
Table of Contents
- PE 15-25 Angle Polisher
- Product Information
- Specifications
- Product Usage Instructions
- 1. Assembly
- 2. Operation
- 3. Maintenance
- Q: What is the power requirement for this product?
- Q: How much does this product weigh?
- Q: How do I assemble the product?
- Q: How do I operate the product?
- Q: How do I maintain the product?
PE 15-25 Angle Polisher
Product Information
Specifications
- Model: PE 15-25 (15250000)
- Power: 230V
- Quantity: 1
- Weight: 36 kg
Product Usage Instructions
1. Assembly
To assemble the product, follow these steps:
-
Attach the armature compl., 230V (PG) to the motor
housing. -
Connect the field coil w.field coil,230 V to the armature
compl. -
Attach the switch 2-pole to the motor housing.
-
Secure the cable clip to the motor housing to hold the cables
in place. -
Install the baffle and electronic unit,230V 50/60Hz into the
motor housing. -
Attach the ball bearings, rubber bushing, washer, hexagon nut,
switch rod, cap, end cap, switch slide, loop handle compl., fixing
set, gasket, fill. head screw(DIN 7985), self-tap. fill. h. screw,
rating plate, bevel gear w.pinion, gear flange compl., gear housing
compl., planet wheel set, compl., brush holder set, fan w. dust
guard, carbon brush set cut-off, retaining ring, O-ring, pressure
spring, push button, bolt, tacho disc, pivoting switch, spindle
shaft, flange compl., O-ring and washer as per the instructions
provided in the user manual. -
Attach the carbon brush with brush holder set 230V to the motor
housing.
2. Operation
To operate the product, follow these steps:
-
Ensure that the product is connected to a power source of
230V. -
Turn on the switch to start the product.
-
Use the loop handle to hold and control the product during
operation. -
Adjust the speed and pressure according to your
requirements. -
After use, turn off the switch and disconnect the power
source.
3. Maintenance
To maintain the product, follow these steps:
-
Regularly clean the product to remove dust and debris.
-
Inspect all parts for any signs of damage or wear.
-
Replace any damaged or worn parts with genuine
replacements. -
Apply grease to lubricate moving parts as per the instructions
provided in the user manual.
Frequently Asked Questions (FAQ)
Q: What is the power requirement for this product?
A: This product requires a power source of 230V.
Q: How much does this product weigh?
A: This product weighs approximately 36 kg.
Q: How do I assemble the product?
A: To assemble the product, please refer to the assembly
instructions provided in the user manual.
Q: How do I operate the product?
A: To operate the product, please refer to the operation
instructions provided in the user manual.
Q: How do I maintain the product?
A: To maintain the product, please refer to the maintenance
instructions provided in the user manual.
PE 15-25 (15250000) 1/3
Pozitie 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 24 25 30 31 32 33 34 52 53 54 55 56 57 58 61 62 63 64 65 70 71 87 88 92 94 124 880 1001 1005
Cantitate 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 4 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1
Numar tip 310010990 311012180 343410120 399999990 399999990 343362490 315013520 339151180 339151200 343082890 143115690 344097870 339133060 143115700 339006390 341100940 343433070 343433030 343433100 343437100 343399690 316067100 339012430 141121640 141116980 141117060 338068660 316066140 316066180 316066890 316066110 316065420 316054850 316065450 141156650 143196000 342003390 343433640 341515640 343433060 343433090 341605360 316066120 143195320 339008020 316067170 344130920 338505780 316067320
PE 15-25 (15250000)
Denumire
PG
Armature compl., 230V
36
Field coil w.field coil,230 V
33
Switch 2-pole
21
Part not needed
Part not needed
Cable clip
12
Motor housing 2 part
21
Baffle
11
Baffle
11
Electronic unit,230V 50/60Hz
32
Ball bearing,6x19x6
13
Rubber bushing
11
Washer,8,05x17x0,4
11
Ball bearing,8x22x7
14
Washer,7,05×19,5×0,2
11
Hexagon nut w.recess
12
Switch rod
11
Cap
15
End cap
11
Switch slide
11
Loop handle compl.
26
Fixing set
23
Gasket
11
Fill. head screw(DIN 7985)
11
Self-tap. fill. h. screw
11
Self-tap. fill. h. screw
12
Rating plate
11
Bevel gear w.pinion
35
Gear flange compl.
50
Gear housing compl.
33
Planet wheel set, compl.
36
Brush holder set
23
Fan w. dust guard
15
Carbon brush set cut-off
22
Retaining ring
11
O-ring
11
Pressure spring
11
Push button
11
Bolt
11
Tacho disc
13
Pivoting switch
11
Spindle shaft
24
Flange compl.
29
O-ring
11
Washer
12
carbonbrush with brusholder Set 230V
27
Grease 100G
31
Diagram
Cable with sleeve
27
2/3
PE 15-25 (15250000) 3/3