LifeReiver 32004 84 Inch Ceiling Fan Light User Manual
- June 7, 2024
- LifeReiver
Table of Contents
LifeReiver 32004 84 Inch Ceiling Fan Light
Safety Information
READ AND SAVE THESE INSTRUCTIONS.
- To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before you begin.
- All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
- Do not place objects in the path of the blades.
- To clean the fixture ,turn off the power, and wait for it to cool, and wipe the fixture with a clean dry, soft cloth.
- After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipmentgrounding conductor on one side of the outlet box and the ungrounded conductor on the other side of the outlet box.
- All screws must be checked and retightened where necessary before installation.
- WARNING: To reduce the risk of electrical shock or fire, not use this fan with any solid-state fan speed LIL control device. It will permanently damage the electronic circuitry.
- WARNING: To reduce the risk of fire or injury do not use this product in conjunction with any variable Lil (rheostat) wall control.
- WARNING: To reduce the risk of personal injury, do not bend the blade brackets when installing the rackets Lil balancing the blades, or cleaning the fan. Do not insert objects.
- WARNING: To avoid possible electrical shock, turn Lil the electricity off at the main fuse box before wiring.
- WARNING: To reduce the risk of electrical shock, this must be installed with an isolating wall control/switch.
- CAUTION: Please use it carefully when working around or cleaning the fan to avoid injury or damage of the fan.
- CAUTION: The fan must be mounted with a minimum of 7.5 ft ( 2. 3 m) clearance from the trailing edge of the blades to the floor.
- CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Fan Parts Included
Dimension Reference
Hardware Included
Exploded View
Installation Instruction
Step 1 MOUNTING
- Take out fan downrod.
- Remove cotter pin and bolt from down rod.
- Take Loosen out jam fan motor screw in the housing. yoke until it is flush with the inside surface.
- Place the down rod inside the canopy, canopy cover, and yoke cover.
- Route wires exiting motor through yoke cover, canopy and down rod.
- Insert bolt through hole in and down rod. Be careful not to damage or cut the fan wires.
- Tighten bolt. Secure with cotter pin through hole in the end of the bolt.
- Secure downrod in position by tightening jam screws.
- Slide yoke cover down and it will flush with the motor housing.
CAUTION: To ensure the wobble-free operation and to avoid damage to the fan, the downrod and the set crew must be completely tightened.
Step 2 INSTALL MOUNTING BRACKET
WARNING: In order to avoid the risk of dropping, this product is only
installed on concrete ceilings or strong wood!
- Lift the fan motor assembly into position, and place the hanger ball into the mounting bracket. Rotate the downrod until the check groove drops into the registration slot and seats firmly. The down rod should not rotate if this is done correctly.
Step 3 Attaching the Fan Blades.
- Attach the blade to the motor with bla de screws and washer.
- Repeat this step for each blade assembly.
CAUTION: When installing the fan, fix the ceiling fan motor on the ceiling before installing the ceiling fan blade
Step 4 Assembling the lamp housing
- Feed the wire through the center hole of the lamp housing.
- Fix the lamp housing with screws.
- Connect the plugs from the motor and LED.
Step 5 The lampshade installation
- Install the lampshade to the lamp housing by turning clockwise to lock it into place.
Step 6 The receiver installation
- Put the receiver in the Mounting Bracket.
Step 7 Wiring the Fan
- Wiring according to the wiring diagram.
Step 8 Attaching the Canopy and Canopy cover
- Slide the canopy up to the ceiling and attach it to the Mounting Bracket with the screws provided. Tighten all screws securely.
- Move the Canopy cover onto the canopy. (the decorative cover comes with magnetism)
CONGRATULATIONS!
YOU HAVE COMPLETED THE INSTALLATION
OPERATION
FUNCTION INSTRUCTION OF EMITTER
- Open the battery cover on the hand-held remote and Install two 1.5V AAA batteries,
- If the emitter can not control the fan:
- When the emitter cannot control the receiver, please check is there any existence of similar remote-controlled products nearby, then check whether they works, because remote-controlled product with the same frequency will disturb each other.
- When the emitter cannot control the receiver, please check whether the battery switch touching normally or not, and correct the positive and negative, full or empty of the power.
- Turn on the power switch, Press and hold the Learning process button for 3 seconds within 10 seconds of power on. If you hear a beep sound, the pairing process is complete
- When installing the fan, the fan ceiling cover doesn’t press the antenna(or other wire), it is easy to break down the wire and is short-circuited.
- Pressing the timer button will activate the timer function. The fan will automatically turn fan and light (if light is on)off after 1,4 or 8 hours.
CAUTION: Do not use with a wall light dimmer switch.
NOTE: The battery will weaken with age and should be replaced before
leaking takes place as this will damage the remote control. dispose of used
batteries properly and keep the battery out of the reach of children.
- All off
- Fan off
- Light on
- Reverse function
- Fan speed
- Light off
- Learning process
- Timer
Troubleshooting Guide
If you have difficulty operating your new ceiling fan it may be the result of incorrect assembly, installation, or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults please check this troubleshooting guide.
Balancing Kit
The Balancing kit should only be used if there is an unacceptable amount of fan wobble after completing all the steps in your owner’s Manual under “Attaching The Fan Blades.”
- Turn the fan on and set the speed control setting to a speed at which the wobbles are the greatest.
- Turn off the fan and allow it to come to a complete stop. Select one blade and place the balance clip on it, halfway between the blade holder and the blade tip on the trailing edge of the blade.
- Turn the fan on. Note whether the wobble has increased or decreased. Turn the fan off, move the clip to another blade, and retest. Repeat this procedure on all blades noting the blade on which the greatest improvement is achieved.
- Move the clip back to the blade that showed the greatest improvement. Move the clip inward and outward on this blade and operate the fan to find the position where the clip gives the greatest improvement.
- Remove the clip and install a balancing weight to the top of the blade along the centre line near the point where the clip was positioned.
- If the fan wobble problem has not been corrected you can try to improve the balancing further by using the balancing clip and additional weights.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>