NICOR RSD41120SBK RSD Surface Mount LED Downlight Instructions NICOR LED RSD Surface Mount LED Downlight
- January 14, 2024
- NICOR
Table of Contents
- RSD41120SBK RSD Surface Mount LED Downlight
- NICOR LED RSD Surface Mount LED Downlight
- Specifications:
- Product Usage Instructions:
- 1. Preparation:
- 2. Mounting:
- 3. Wiring:
- 4. Installation:
- 5. Power On:
- 6. Adjusting the Light:
- 7. Maintenance:
- Q: Can I install the NICOR LED RSD Surface Mount LED Downlight
- Q: What voltage and frequency is this product designed
- Q: Can I install this fixture in a different type of junction
RSD41120SBK RSD Surface Mount LED Downlight
NICOR LED RSD Surface Mount LED Downlight
Specifications:
-
Model(s): RSD41120SBK, RSD41120SNK, RSD41120SOB, RSD411
20SWH -
Compatible with 4 Pancake Box, 4/0 J-Box, and Non-metallic 4
J-Box -
Suitable for use in wet locations
-
Designed for use on 120VAC, 60Hz circuits
-
Diameter (D): 6.2 inches (157mm)
-
Height (H): 1.2 inches (31mm)
Product Usage Instructions:
1. Preparation:
Before starting the installation process, ensure that the power
is turned off at the circuit breaker or fuse box to avoid any
electrical hazards.
2. Mounting:
Choose a suitable location for the NICOR LED RSD Surface Mount
LED Downlight. It can be installed in a 4 Pancake Box, 4/0 J-Box,
or Non-metallic 4 J-Box.
Ensure that the mounting surface is sturdy and capable of
supporting the weight of the fixture.
3. Wiring:
Connect the wiring according to your electrical setup. Make sure
to follow local electrical codes and regulations.
If you are unsure about the wiring process, it is recommended to
consult a qualified electrician.
4. Installation:
-
Remove the existing fixture or cover plate from the chosen
mounting location. -
Position the NICOR LED RSD Surface Mount LED Downlight over the
mounting location. -
Secure the fixture in place using the provided screws or
mounting brackets.
5. Power On:
After completing the installation, turn the power back on at the
circuit breaker or fuse box.
6. Adjusting the Light:
The NICOR LED RSD Surface Mount LED Downlight allows for
adjustable light direction. Gently rotate the fixture to achieve
the desired lighting angle.
7. Maintenance:
Regularly clean the surface of the fixture with a soft, dry
cloth to remove dust and debris. Avoid using harsh chemicals or
abrasive materials that may damage the finish.
FAQ:
Q: Can I install the NICOR LED RSD Surface Mount LED Downlight
in a damp location?
A: Yes, this fixture is suitable for use in wet locations.
Q: What voltage and frequency is this product designed
for?
A: The NICOR LED RSD Surface Mount LED Downlight is designed for
use on 120VAC, 60Hz circuits.
Q: Can I install this fixture in a different type of junction
box?
A: No, this fixture is specifically designed to fit in 4 Pancake
Box, 4/0 J-Box, and Non-metallic 4 J-Box.
NICOR LED
RSD Surface Mount LED Downlight
MEASUREMENT GUIDE
Model(s): RSD41120SBK, RSD41120SNK, RSD41120SOB, RSD411 20SWH
This fixture will fit in 4″ Pancake Box, 4/0 J-Box and Non-metallic 4″ J-Box
WARNING: ,Risk of electric shock. Disconnect power at fuse or circuit breaker
before installing or servicing. ·To prevent early lamp failure, lamp should
only be installed in operating environments between -20°( and+ 40°C (-4°F and
104°F) ·No user serviceable parts inside. To avoid electric shock do not
disassemble product. ·This product is not intended for use in emergency light
fixtures or exit signs.
ATTENTION: Turn power off before inspection, installation, or removal.
Suitable for use in wet locations. Use only on 120VAC, 60Hz circuits.
Fixture RSD4S
Diameter (D)
6.2″ (157mm)
Height (H)
1.2″ (31mm)