AKT1 SPORT B08PCBZDF8 Electronic Headphones User Manual
- June 4, 2024
- AKT1 SPORT
Table of Contents
AKT1 SPORT B08PCBZDF8 Electronic Headphones User Manual
INSIDE THE BOX
- 1 x Earbud Unit
- AKT1 Challenge Coin
- 3 Pairs of Foam Eartips (S,M,L)
- 3 Pairs of Silicone Eartips (S,M,L)
- Carry Case
- Type-C USB Charging Cable
- Cable Cinch
- User Manual
FOAM TIP FITTING PROCEDURE
**ALWAYS FIT AND SECURE EARTIPS WITH THE UNIT TURNED OFF.
**
- Mould the soft earhook to fit around your ear as shown.
- Select the proper size ear tip to fit your ear canal. This ear tip should form a complete seal blocking out sound. This is critical to achieve the highest NRR rating and protect your hearing.
- Compress the foam tip by rolling between your fingers, as much as possible.
- Quickly insert compressed foam tip into the ear canal before it expands and seals the ear canal.
- Hold in place for approximately 10 seconds to insure the ear tip expands and seals the ear canal.
- Test this with the headphone turned off. Clap your hands and listen to the sound level. If the ear buds are the correct size and properly inserted, outside sound should be significantly muted. If not, take the foam tip out of your ear canal and repeat step 2 – 3.
POWERING ON/OFF
-
Press and hold the POWER/BLUETOOTH BUTTON for 3 seconds
and the INDICATOR LIGHT will flash BLUE 3 times. At this stage, both the Bluetooth and Hearthrough is powered on. -
The earphone will then enter automatic pairing and the INDICATOR LIGHT will flash RED and BLUE alternately.
-
Go to Bluetooth settings on your device. Turn Bluetooth on and connect earphone by choosing “StrikePRO HTBT”.
-
Once connected, the INDICATOR LIGHT will illuminate STEADY BLUE and your earphone is connected and ready to use.
-
If bluetooth connection is not detected in 5 minutes, the INDICATOR LIGHT will flash blue every 3 seconds showing that the earphone is in “hearthrought only” state. In this state,hearthrough is still active and if you want to connect to a bluetooth device again, double-tap the POWER/BLUETOOTH BUTTON to re-activate pairing search.
-
Once you complete use of your earphones, press and hold the POWER/ BLUETOOTH BUTTON for 3 seconds and the INDICATOR LIGHT will flash RED 3 times. Your earphones are now turned off.
WHILE IN USE
BLUETOOTH INSTRUCTIONS
FOR CALLS
- Tap the POWER/BLUETOOTH BUTTON once to pick up or end calls.
- Tap the BLUETOOTH BUTTON twice to redial the last incoming or outgoing number.
- When there is another incoming call during a call, tap the POWER/ BLUETOOTH BUTTON once to end the original call and receive a new call. Tap POWER/BLUETOOTH BUTTON twice to put the original call on hold and receive new call. Tap the POWER/ BLUETOOTH BUTTON twice to alternate between the two calls.
FOR MEDIA
- Tap the BLUETOOTH BUTTON once to play/pause music.
- Tap VOLUME UP/DOWN BUTTON once to increase/decrease media volume.
- Press and hold the VOLUME UP/DOWN BUTTON for 2 seconds to skip to the previous/next track.
- Press and hold the BLUETOOTH BUTTON to activate SIRI/BIXBY/ ALEXA etc … platforms.
HEAR THROUGH INSTRUCTIONS
- The default sound level upon powering on the unit is set at safe sound levels and provides protection from loud external sounds while delivering natural hearing.
- Tap on the HT VOLUME UP/DOWN button to increase/decrease the volume in increments . 8 volume increments are provided above initial power on level to provide hearing augmentation. Please beware of sound levels when volume is increased.
BATTERY CHARGING
- Insert USB-C charging cable to an AC charger (not included) or a computer USB CHARGING PORT.
- Insert the USB-C end into USB CHARGING PORT.
- The INDICATOR LIGHT lights up RED while the unit is being charged.Once the battery is fully charged, the light will turn BLUE.
- When charging with the earphone powered off, the earphone will automatically power on and start searching for a pairing device as soon as the USB-C chord is detached from the charging port.
- Battery charging time is approximately 2 hours.
FCC STATEMENT
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
MODEL : STRIKEPRO HTBT
FCC ID : 2A5PL-STRIKEPROHTBT
BLUETOOTH DID : D054382
The AKT1 StrikePRO HTBT earbuds operate differently than typical BT earbuds or earplugs, and especially different from earbuds for music listening and entertainment. They are first of all hearing protection devices with the primary function of protecting you from hearing loss.
The hearing augmentation is state of the art digital sound enhancement with the result of very natural hear through capabilities, allowing you to maintain not only more accurate situational awareness, but increased awareness and focus on the task at hand.
The BT functionality is State of the Art using BT 5.0 with better connectivity, a wider band for music listening and Qualcomm CVC noise cancellation. During phone calls, you will note better voice recognition, and more accurate sound recreation. For music listening, you will note that the latest BT version enhances clarity and bandwidth significantly. The combination of sound isolation from environmental noise and absolute design control of the bud itself with acoustics in mind with every design decision.
We sincerely built these with the user in mind and made every decision without
compromise. We think you will find that to be evident in use.
Team AKT1 Sport
PERFORMANCE WITHOUT COMPROMISE
