Solaira Heaters SCOSYXL30277-C Solaira Cosy XL 277V Double User Manual
- June 16, 2024
- Solaira Heaters
Table of Contents
Solaira Heaters SCOSYXL30277-C Solaira Cosy XL 277V Double
Product Information
Specifications
- Model: Solaira Cosy XL
- Voltage: 277V
- Frontage/Fascia Heater Models:
- SCOSYXL30277-C
- SCOSYXL30277LL-C
- SCOSYXL40277-C
- SCOSYXL40277LL-C
- Stainless Steel Frontage/Fascia Heater Models:
- SCOSYXL30277-C (Color Code: Low Light Candle)
- SCOSYXL30277LL-C (Color Code: Low Light Candle)
- Weatherproof: Yes
- Suitable for: Outdoor and Indoor Use (Commercial and Industrial); Residential outdoor use only for 240V
- Infrared Heaters
Product Usage Instructions
Safety Precautions
-
Read all instructions before using this heater.
-
Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
-
This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 6 feet (1.8m) from the front of the heater and keep them away from the sides and rear.
-
Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
-
When not in use, disconnect the supply.
-
Do not operate any heater with a damaged cord or after the heater malfunctions, or has been dropped or damaged in any manner. Return heater to an authorized service facility for examination, electrical or mechanical adjustment, or repair.
-
This heater is not intended for use in bathrooms, laundry areas, and similar locations. Never locate the heater where it may fall into a bathtub or other water container.
-
Do not run the cord under the carpeting. Do not cover the cord with throw rugs, runners, or the like. Arrange the cord away from the traffic area so that it will not be tripped over.
-
To disconnect the heater, turn the controls off.
WARNING – Each power supply circuit shall be provided with disconnecting means and the disconnecting means shall be grouped. -
Do not insert or allow foreign objects to enter any opening as this may cause an electric shock or fire, or damage the heater.
-
To prevent a possible fire, do not block openings in any manner.
-
A heater has hot parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
-
Do not cover or otherwise obstruct the heater.
-
Do not touch the heater during operation as the body becomes very hot and can cause burns. Particular attention has been given where children and vulnerable people are present.
FAQ (Frequently Asked Questions)
- Q: Can I use this heater in my bathroom?
- A: No, this heater is not intended for use in bathrooms or similar locations. It should not be placed where it may fall into a bathtub or other water container.
- Q: What should I do if the cord is damaged?
- A: If the cord is damaged, do not operate the heater. Return it to an authorized service facility for examination, electrical or mechanical adjustment, or repair.
- Q: How far should combustible materials be kept from the heater?
- A: Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 6 feet (1.8m) away from the front of the heater and keep them away from the sides and rear.
- Q: Is this heater suitable for outdoor use?
- A: Yes, this heater is suitable for outdoor use in non-hazardous areas. However, for residential use, it is recommended for outdoor use only with a 240V power supply.
- Q: Can children or invalids use this heater?
- A: Extreme caution should be exercised when any heater is used by or near children or invalids. It is recommended to supervise their usage and not leave the heater operating and unattended.
- Q: How should I move the heater?
- A: If handles are provided, use them when moving the heater to avoid burns from hot surfaces.
STANDARD FRONTAGE/FASCIA HEATER MODELS FOR CANADA & USA:
- SCOSYXL30277-C (240V – 2 × 1125W [2250W TOTAL] / 277V – 2 × 1500W [3000W TOTAL])
- SCOSYXL30277LL-C (240V – 2 × 1125W [2250W TOTAL] / 277V – 2 × 1500W [3000W TOTAL]) LOW LIGHT CANDLE
- SCOSYXL40277-C (240V – 2 × 1500W [3000W TOTAL]) / 277V – 2 × 2000W [4000W TOTAL])
- SCOSYXL40277LL-C (240V – 2 × 1500W [3000W TOTAL]) / 277V – 2 × 2000W [4000W TOTAL]) LOW LIGHT CANDLE
STAINLESS STEEL FRONTAGE/FASCIA HEATER MODELS FOR CANADA & USA:
- SCOSYXL30277SS-C (240V – 2 × 1125W [2250W TOTAL] / 277V – 2 × 1500W [3000W TOTAL])
- SCOSYXL30277SSLL-C (240V – 2 × 1125W [2250W TOTAL] / 277V – 2 × 1500W [3000W TOTAL]) LOW LIGHT CANDLE
- SCOSYXL40277SS-C (240V – 2 × 1500W [3000W TOTAL] / 277V – 2 × 2000W [4000W TOTAL])
- SCOSYXL40277SSLL-C (240V – 2 × 1500W [3000W TOTAL] / 277V – 2 × 2000W [4000W TOTAL]) LOW LIGHT CANDLE
WEATHERPROOF INFRARED HEATERS SUITABLE FOR OUTDOOR AND INDOOR USE COMMERCIAL AND INDUSTRIAL, (RESIDENTIAL 240V OUTDOOR USE ONLY)
IN NON-HAZARDOUS AREAS
INFORESIGHT CONSUMER PRODUCTS INC. 125 Traders Blvd. E Unit # 4,
Mississauga, Ontario L4Z 2H3 Tel :
905-568-7655 Fax :
905-568-7521 Email :
info@solairaheaters.com Website :
www.solairaheaters.com
IMPORTANT
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
IMPORTANT INSTRUCTIONS
When using electrical short-wave INFRARED HEATERS, basic precautions should
always be followed to reduce the risk of fire, electric shock, and injury to
persons, including the following:
-
Read all instructions before using this heater.
-
Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
-
This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 6 feet (1.8m) from the front of the heater and keep them away from the sides and rear.
-
Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
-
When not in use, disconnect the supply.
-
Do not operate any heater with a damaged cord or after the heater malfunctions, or has been dropped or damaged in any manner. Return the heater to an authorized service facility for examination, electrical or mechanical adjustment, or repair.
-
This heater is not intended for use in bathrooms, laundry areas and similar locations. Never locate the heater where it may fall into a bathtub or other water container.
-
Do not run the cord under the carpeting. Do not cover the cord with throw rugs, runners, or the like. Arrange the cord away from the traffic area so that it will not be tripped over.
-
To disconnect the heater, turn the controls off.
WARNING: Each power supply circuit shall be provided with disconnecting means and the disconnecting means shall be grouped. -
Do not insert or allow foreign objects to enter any opening as this may cause an electric shock or fire, or damage the heater.
-
To prevent a possible fire, do not block openings in any manner.
-
A heater has hot parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
-
Do not cover or otherwise obstruct the heater.
-
Do not touch the heater during operation as the body becomes very hot and causes burns. Particular attention has been given where children and vulnerable people are present.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
The 240V / 277V heaters have 2 × cords from the junction boxes which must be
permanently connected to a properly grounded supply.
WARNING : RISK OF FIRE
- Keep combustible material such as furniture, papers, clothes, and curtains at least 6 feet (1.8m) from the front of the heater and away from the sides and rear.
- Heaters are not intended for use as indoor residential or as a household heaters. They may be used for outdoor residential 240V use.
INTRODUCTION
The Solaira Cosy XL 277V Double heater produces short-wave infrared heat like the sun, warming people and objects and not the air in between. It is mounted on an adjustable bracket that allows the heat to be directed exactly where it is required. Its attractive, lightweight design means that it is effective yet unobtrusive. The short-wave infrared weatherproof heater is designed for indoor and outdoor use.
Please read the following instructions carefully before use. The safety of this heater is guaranteed only by its correct usage in accordance with these instructions, therefore they should be retained for future reference.
CAUTION
Before using this appliance:
- Check that the voltage indicated on the unit’s rating label corresponds to the mains supply voltage.
- Do not install heaters less than the minimum height from the floor as specified below in the specification tables.
- Ensure that the heater has been securely fastened in its final mounting position.
- WARNING – This appliance must be grounded and hard-wired!
- WARNING – Keep the supply cables away from the front and body of the heater which will get hot during use.
- Do not cover or obstruct the heater while it is in use.
- Do not insert any object through any slot or opening in the heater.
- Do not use it if a grille is not present.
- WARNING – Before replacing the lamp emitter or cleaning the unit, ensure that the hard-wired circuit is disconnected from the main supply. Note: always ensure that the lamp emitters are cool before handling.
- Do not handle a lamp emitter with bare hands. If it is inadvertently touched, remove finger marks with a soft cloth and methylated spirit or rubbing alcohol. Otherwise, the marks will burn into the lamp emitter during use causing premature heater failure.
- The heater is not intended for use by young children and must be supervised by a responsible person at all times.
SPECIFICATION
TABLE – 240V / 277V HEATERS
Model Types
| SCOSYXL30277-C & SCOSYXL30277LL-C, SCOSYXL30277SS-C & SCOSYXL30277SSLL-C|
SCOSYXL40277-C & SCOSYXL40277LL-C SCOSYXL40277SS-C SCOSYXL40277SSLL-C
---|---|---
Voltage| 240V / 277V
No. of Emitters × Power| 2 × 1125W / 1500W|
2 × 1500W / 2000W
Current per Emitter| 4.7A / 5.4A| 6.3A / 7.2A
Total Power of Unit| 2250W / 3000W| 3000W / 4000W
Total Current of Unit| 9.4A / 10.8A| 12.5A / 14.4A
Min. mounting height from floor| 7ft 10½in (240cm)
Min. distance from the ceiling| 8¾in (22cm)
Min. distance from the sidewall| 17in (43cm)| 17in (43cm) /
25in (64cm)
Dimensions – W × H × D| 50in × 4½in × 3½in
(127cm × 11cm × 9cm), 48in × 4½in × 3½in
(122cm × 11cm × 9cm)
Weight| 13.2lbs (6.0kg)
INSTALLATION
The 240V / 277V heaters are fitted with a 2 × supply cords measuring 79 inches
(200cm) each for permanent connection.
- WARNING : Wiring procedures and connections should be by the National Electric Code (NEC) and local codes.
- WARNING : If a supply cord becomes damaged, it must be immediately replaced by a qualified person to avoid a hazard.
- CAUTION : Disconnect the electric power supply before working on the circuit wiring to prevent electric shock.
- CAUTION : Please observe the minimum safe distance between the heater body and any inflammable surfaces.
- CAUTION : When the electrical connection is outside a weatherproof socket must be used having ground fault protection (GFCI or GFI).
NOTE : CONSULT A QUALIFIED ELECTRICIAN, IF IN DOUBT.
MOUNTING
CAUTION
Always isolate the heater from the mains supply when mounting or adjusting
the heater position.
The Solaira Cosy XL 277V Double heater should be mounted in a horizontal (Fig. A) manner only.
-
Securely fasten the heater brackets to the mounting surface using the fixing holes in the brackets. See Fig. C for the mounting hole centres of the brackets. Please refer to the specification table for the recommended positioning of the heater.
-
The heater bracket can be used to adjust the direction of the heater up and down (see Fig. B). This is done by loosening the bolts fixing the heater to the bracket, and then retightening once the correct position is achieved. Fix in the required angular position.
HORIZONTAL MOUNTING -
Secure the supply cords so they are directed away from the heater and are not resting on the body or obstructing the air vents.
- CAUTION : When mounting the heater, do not position the heater at an angle more than 50° or less than 45° as shown in Fig. A.
- CAUTION : The heater should be mounted with the minimum clearances adhered to. Please refer to the specification table for the recommended positioning of the heater. Do not install the heater in a corner!
- CAUTION : Always allow the heater to cool before attempting to reposition/move. Never attempt to move the heater while it is switched on!
- CAUTION : Observe the minimum safe distance between the heater body and inflammable surfaces and objects when mounting (see specification table).
MOUNTING TO A CEILING/OVERHANG
CAUTION
Always isolate the heater from the main supply when mounting or adjusting
the heater position.
The Solaira Cosy XL 277V Double heater can be mounted to a ceiling or overhang (as shown in Fig. D) using 2 × optional ceiling brackets (not supplied).
- Securely fasten the heater brackets to the mounting surface using the fixing holes in the brackets. See Fig. F for the mounting hole centres of the brackets. Please refer to the specification table for the recommended positioning of the heater.
- Mount the heater to the brackets as shown in Fig. E and fix it in the position by tightening the fixing bolt on the bracket at the rear of the heater.
- Secure the supply cables so the cables are directed away from the heater and are not resting on the body or obstructing the air vents.
- CAUTION : The heater should be mounted with the minimum clearances adhered to. Please refer to the specification table for the recommended positioning of the heater. Do not install the heater in a corner!
- CAUTION : The heater should always be angled downwards when mounting this way
- CAUTION : Always allow the heater to cool before attempting to reposition/move. Never attempt to move the heater while it is switched on!
- CAUTION : Observe the minimum safe distance between the heater front and inflammable surfaces and objects when mounting.
CIRCUIT DIAGRAM
MAINTENANCE
NOTE : For replacement lamp emitters or spare parts (see diagrams on next page) please contact your local distributor quoting model type and rating from the rating label. Your replacement lamp emitter must be the same as the one it was supplied with. Failure to fit the same type can cause the heater to prematurely fail.
CAUTION : Always isolate the mains power from the heater or heater assembly before replacing lamp emitters or any maintenance procedure including cleaning.
CAUTION : Should dust or dirt appear on the reflectors, it is recommended that the grilles and lamp emitters are removed and the reflectors are wiped with a lint-free cloth before reassembling (see lamp emitter replacement instructions).
YOUR REPLACEMENT LAMP EMITTER
CAUTION : Please ensure that the length of the wires on the replacement lamp emitter is the same as shown in the diagram below (Fig. H).
COSY XL DOUBLE STANDARD COMPONENT PART DIAGRAM
COSY XL DOUBLE STAINLESS STEEL COMPONENT PART DIAGRAM
REPLACING A LAMP EMITTER
CAUTION
Disconnect from the mains power supply before any attempts are made to
replace a lamp emitter. Contact your distributor for the correct replacement
quoting model type and rating from the rating label. We recommend you read
through the procedure and refer to the parts diagram on the previous page of
this manual before commencing work.
- Ensure the heater and lamp emitters are cool and the power supply is disconnected before disassembly.
- Remove the heater from its mounted position should it not be safe to work on it while mounted.
- Remove the screws from the junction box (Fig. K) and lift off the cover to the box in which the lamp emitter will be replaced.
- Disconnect the lamp emitter wires from the connector blocks by unscrewing the screws highlighted above in Fig. L.
- Unscrew the four screws (see Fig. M) from the end cover and remove them from the heater body. Repeat at the opposite end.
- Slide out the side covers from both ends and slide out the guard from either end as shown in Fig. N.
- Remove the two screws as highlighted in Fig. P to take out the side reflector bracket and reflector assembly that allows access to the lamp emitter holding clip. Repeat at the opposite end of the lamp emitter.
- Where the lamp emitter wires are fed through the gasket into the junction box (Fig. P), gently pull the lamp emitter wires through the body of the heater so the wires exit the junction box.
- At the opposite end of the lamp emitter, the wire will be visible in the lamp emitter wire tube so gently pull the long wire (Fig. Q) out of the tube until it is free.
- One at a time pull the spring clips back in the direction shown in Fig. R and lift the ceramic caps of the lamp emitter to remove it from the heater.
- The lamp emitter should now be removed from the heater. Refit the new lamp emitter in reverse order ensuring the ceramic caps are correctly seated in the lamp emitter holders, no wires are trapped and all screws are fully tightened.
Due to our policy of ongoing improvement, we reserve the right to make changes without notice.
© 2023 INFORESIGHT CONSUMER PRODUCTS INC. Ref No. 043499-EN-S Issue No. Oa
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>