X-IMVNLEI X-IDRONE19 Drone With Camera Instruction Manual

X-IMVNLEI X-IDRONE19 Drone With Camera

Important safety information

1. This product is not a toy, but a precision device that integrates professional knowledge of mechanics, electronics, aerodynamics, and high-frequency emission. It needs to be assembled and debugged correctly
   to avoid accidents. The product owner must use a safe way to operate the control. Improper operation may cause serious personal injury or property damage. We are not responsible for this, because we cannot control the process of assembly, use, and operation after the product is sold.

2. This product is suitable for people who have experience in operating models and are older than 14 years old.

3. The flight site must be a local legal remote control model flight site.

4. Once the product is sold, we will not be liable for any safety responsibilities arising from operation, use, and control.

5. In case of use, operation, maintenance, and other problems, we entrust the dealer to provide technical support and after-sales service. Please contact your local dealer.

Safety precautions

The remote control aircraft is a high-risk product, so be sure to stay away from the crowd when flying. Improper assembly, damage to the fuselage, malfunction of the remote control, and unfamiliar operation may cause unforeseen accidents such as damage to the aircraft or personal injury. Pilots must pay attention to safety and understand the responsibility for accidents caused by their negligence.

1. Stay away from obstacles and people
   The remote control aircraft has an uncertain height speed and state during flight, and it is potentially dangerous. When flying, the aircraft must be far away from crowds, high-rise buildings, high-voltage power lines, etc., and at the same time, avoid flying in harsh weather such as wind, rain, and thunderstorms to ensure the safety of the pilot, surrounding people, and property.

2. Keep away from the humid environment
   The inside of the aircraft is composed of many precision electronic components and mechanical parts, so we must prevent the aircraft from getting wet or moisture into the fuselage to avoid accidents caused by mechanical and electronic component failure!

3. Safe operation
   Please operate the remote control aircraft according to your own status and flying skills. Fatigue, poor spirits, or improper operation will increase the probability of accidents.

4. Do not touch high-speed rotating parts
   When the propeller is flying at high speed, please keep the pilot, surrounding people, and objects away from the rotating parts to avoid danger and damage.

5. Keep away from heat
   The remote control aircraft is composed of metal, fiber. plastic. electronic components and other materials. so keep away from heat sources and prevent the sun as much as possible to avoid deformation and damage caused by high- temperature

Choking hazard
WARNING  not for children under 3 years due to small parts included.

SPECIFICATIONS AND COLORS OF CONTENTS MAY VARY FROM PHOTO
Please read the manual carefully before using the product and keep this manual for future reference.

Transmitter function introduction

Outdoor Mode

1. When flying outdoors, the bottom optical flow camera will not assist the drone to hover stably in the air when the drone height is lower than lm or higher than Sm, or when flying in a field such as grass or snow. So you need to turn off the optical flow function to enter the doormode.
2. When optical flow mode is off, if the drone appears to be off-flying, you can adjust the balance of the drone through the fine-tuning function of the remote control For details, please refer to point 5 on page 4 of the user manual.

Battery installation and charging instructions for transmitter and drone

Battery installation of transmitter:

• Follow the electrode instructions in the battery compartment as shown in the figure(+/-).
• Insert the battery correctly (as shown in the picture).
• The remote control uses 3 AA 1. SV non-rechargeable batteries.

Drone battery charging

1. Use a USB cable to connect to the computer’s USB port to charge the battery: One end of the USB charging cable is inserted into the drone battery, and the other end is connected to the power adapter. The indicator light is on when charging, and it is off when it is fully charged.
2. Install the drone battery:
   Put the charged battery into the battery holder of the drone, and then align the battery plug with the power input socket on the drone to connect to the power source. After connecting, turn on the power of the drone, and the drone lights will be on at this time.

Note : Always remove the battery when the drone is not in use.

Remote control operation

1. Mobile phone holder
2. Pair the drone with the transmitter Turn on the power switch of the drone and place the drone on level ground. At this time, the drone indicator flashes, turns on the power switch of the transmitter, pushes the throttle stick(left stick) to the highest position,n and pulls it down. The buzzer will sound “Beep”! The light keeps on and the pairing is complete.
3. After completing the pairing, place the drone on a flat ground. Tilt the joystick to the lower right corner at the same time, the buzzer emits a beep, and the drone light flashes and then stays on, indicating that the drone calibration is completed!
4. Start the drone After pairing the drone with the transmitter, push the left stick to the 7 o’clock position and the right stick to the 5 o’clock position at the same time to unlock the drone(as the figure). Then the motor will rotate, and push the left stick upward for the drone to take off.

Flight control

Throttle (left stick)

Go Forward and backward (right joystick)(the side with the camera is the front )

Turn left/ Turn right

Rotate clockwise and counterclockwise (the side with the camera is the front)

Fine-tuning ( There is a camera in front of the drone)

Speed adjustment

Three speeds can be selected, low speed, medium speed, and high speed. After the remote control is turned on, the default is a low speed. Press the remote control button to make two beeps, ii will fly at medium speed, Three beeps mean high speed, beep once, means the drone is back to low speed.
(Low speed is recommended for beginners)

Record video or take a picture photo by the transmitter

1. Recording and photographing buttons (The recording and photographing buttons of the remote control are the same as those on the APP. When using the remote control to control the drone, you can use the recording and photographing buttons on the remote control, but those on the APP cannot be used.) prompt:
2. When using the FPV function of the APP, the mobile phone can find the WIFI transmitted by the drone to connect after the drone is powered onfor  20 seconds, so that the remote control can begin to use
   the video or camera function.

3D Flip by the transmitter

Press the one-key flip button and then push the directional joystick to flip in different directions.
Warning : 3D flip consumes a lot of power and should be used sparingly; novice users are advised to use this function in open spaces.

Direction definition and mode selection of headless mode

When switching to headless mode, the drone will give up its front, back, left, and right orientation.
Use the remote control as a reference to reposition the front, back, left, and right. Such as: when the right joystick is pushed up, The drone goes forward; when the right joystick is pulled down, the drone goes backward. When the right joystick is pushed to the left, the drone turns left, and when the right joystick is pushed to the right, the drone turns right.

1. Before taking off, place the drone in the direction indicated by the picture, Then press the one key lake off button.
2. When flying, press the headless mode button and the remote controller will emit two beeps. The rapid flashing of the drone lights means that headless mode is on. Press the headless mode button again and the remote control emits a beep to exit the headless mode.

Troubleshooting

the indicator light on the drone

flashes continuously,

and there is no

| The remote control and the drone are not successfully paired.| Please re- pair the remote control with the drone.
response to the|  |
operation.|  |

After inserting the drone battery, the drone does not respond

| 1.  Check whether the remote control and drone are inserted into batteries .

2.  Check whether the remote control and drone battery are in a low battery state

3.  Check whether the positive and negative poles of the battery are in poor contact

| 1. Turn on the remote control and insert the drone battery.

2. Use a fully charged battery

3. Re-insert the battery and confirm whether the contact between the battery and the positive and negative plates of the battery is normal.

When pushing the

throttle stick, the main motor does not rotate, and the indicator light on the drone starts to flash

|

The drone’s lithium polymer battery is low

|

Charge the battery or replace with another fully charged battery

The drone motor keeps rotating but

the drone cannot

| 1. Deformation of the propeller

2· The drone battery is low

| 1. Replace the propeller

2. Charge the battery or replace with

another fully charged battery

take off|  |
The drone shakes

severely

| Deformation of the propeller| Replace the propeller
The drone drifts forward or backward| The gyroscope’s midpoint is abnormal.| The remote control can be calibrated, or restarted and re-pairing with the drone
The drone drifts left or right| The gyroscope’s midpoint is abnormal.| The remote control can be calibrated, or restarted and re-pairing with the drone

After-sales information:

X-IMVNLEl®I© ALL RIGHTS RESERVED
E-mail: ximvnlei@gmail.com (24hr/7d)

Please read the manual carefully before using the product and keep this manual for future reference. This content is subject to change If you have any questions about this document, please contact X.IMVNLEI by sending a message to us.

X19 App Operation Manual
Download and install the mobile App
Search “KY UFO” in “App Store” or “Google Play” to download and install. 2. Scan the QR code below to download and install.

Connection steps:

1. Turn on the power switch of the product.
2. 0pen the mobile phone setting option, start WiFi, find “Drone-X” in the WiFi search list, and click Connect until the connection is successful.
3. 0pen the app and click the “start” icon to enter the real-time interface.

Setting:
Click Setting after connection, and enter system setting.

1. Find Operation instructions
2. Change the flight control model
3. Change App Languages.

Operating instructions:

1. Function column:
   After connecting to the app, click the Start button, and click the function column.

2. Horizontal calibration:
   Place the drone on a horizontal surface for calibration, click the Calibration button and the drone’s light flashes quickly to always on to indicate that the calibration is successful.

3. One-key takeoff/One-key landing:
   Press the one-key takeoff/one-key landing button to start the drone, and the drone will fly to a height of about 1.5 meters in the air.

Various functions are shown in the figure below:

1. Gesture: After pressing this function, stretch out the yeah gesture to the camera to take a photo, and hold your fist to record a video.
2. Trajectory: Press this button, to draw a trajectory on the screen, and the drone will fly according to the trajectory.
3. Gravity: Press this button, keep the phone level, and control the drone forward, backward, left, and right through the center of gravity.
4. Speed: Three adjustable speeds, adjust the speed according to the flight conditions.
5. Emergency stop: When there is danger, press this button, and the drone will stop flying directly.

After-sales information:

Please read the manual carefully before using the product and keep this manual for future reference.
This content is subject to change If you have any questions about this document, please contact X-IMVNLEI by sending a message to us.
E-mail : ximvnlei@gmail.com (24hr/7d)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>