cybex Pallas B-Fix 9-18 Child Car Seat User Guide

: June 16, 2024
: CYBEX

Table of Contents

Pallas B-Fix 9-18 Child Car Seat
CERTIFICATION
IMPORTANT INFORMATION
PRODUCT PARTS
INITIAL ASSEMBLY
THE CORRECT POSITION IN THE VEHICLE
INSTALLING THE CHILD SEAT IN THE VEHICLE
ADJUSTING THE HEADREST
CORRECT INSTALLATION MODE
SECURING THE CHILD WITH IMPACT SHIELD – GROUP 1 (9–18 KG)
MANUFACTURER’S WARRANTY AND DISPOSAL REGULATIONS
Documents / Resources

Pallas B-Fix 9-18 Child Car Seat

cybex Pallas B-Fix 9-18 Child Car Seat PALLAS B-FIX
UN R44/04, Gr. 1/2/3 | 9-36 kg
User guide
GO TO WWW.CYBEX-ONLINE.COM
TO WATCH AN INSTRUCTIONAL VIDEO

CERTIFICATION

UN R-44/04
CYBEX Pallas B-Fix – group 1, 9 to 18 kg
CYBEX Solution B-Fix – group 2/3, 15 to 36 kg
Recommended from approx. 9 months to 12 years cybex Pallas B-Fix 9-18 Child
Car Seat - fig 3 Thank you for deciding on the Pallas B-Fix when choosing your child seat.
Carefully read the instructions before installing the seat in your car and always keep these instructions to hand in the designated user guide storage compartment (a).

IMPORTANT INFORMATION

Without the approval of the Type Approval Authority, the child seat may not be modified or added to in any way.
In order to keep your child properly protected, it is absolutely essential that you use the child seat as described in this manual.
This child seat may only be installed on vehicle seats which are approved for the use of child restraint systems according to the vehicle manual.
Only suitable for vehicle seats with automatic three-point belts approved in accordance with UN Regulation No. 16 or a comparable standard.
Do not use any load bearing contact points other than those described in the instructions and marked on the child restraint.
The full surface of the backrest of the child seat must make contact with the backrest of the vehicle.
The shoulder belt must run upwards and back at a recline. It must never run forward to the upper belt point in your vehicle.
The vehicle belt buckle must never cross the belt guide of the seat. If the belt whip is too long, the child seat is not suitable for use in this position in the vehicle. In case of doubt please contact the child restraint manufacturer.
The three-point vehicle belt must only be passed through the designated routings. The belt routings are described in detail in this manual and are marked in red on the child seat.
The lap belt must run as low as possible across your child’s groin to have optimum effect in the event of an accident. Before each use make sure that the automatic three-point vehicle belt is correctly adjusted and fits tightly to the child’s body. Never twist the belt!
Only an optimally adjusted headrest can offer your child maximum protection and comfort while ensuring that the shoulder belt can be fitted smoothly.
For usage in Group 1 the impact shield must be used.
The child seat must always be secured correctly with the vehicle belt in the vehicle even when not in use.
Always ensure that the child seat is never jammed when closing the car door or adjusting the back seat.
Luggage or any other objects present in the vehicle must always be firmly secured. Otherwise, they may be thrown within the car, which could cause fatal injuries.
The child seat must never be used without the seat cover. Ensure that only an original CYBEX seat cover is used, as the cover is a key element of the seat’s function.
Never leave your child unattended in the car.
The parts in the child restraint system heat up in the sun and could potentially burn your child’s skin. Protect your child and the child seat from direct sun exposure.
An accident may cause damage to the child seat that is not identifiable with the naked eye. Please replace the seat after an accident. In case of doubt, please consult your dealer or the manufacturer.
Do not use this child seat for more than 11 years. The child seat is exposed to high stress during its product life span, which leads to changes in the quality of the material with increasing age.
The plastic parts can be cleaned with a mild cleaning agent and warm water. Never use harsh cleaning agents or bleaches!
Some vehicle seats are made of sensitive materials. The use of child seats may leave marks and/or cause discolouration. To prevent this, you can place a blanket or towel or similar underneath the child seat to protect the vehicle seat.

PRODUCT PARTS

(a) User Guide Storage Compartment
(b) Backrest
(c) Adjustable Headrest
(d) Headrest Height Adjuster
(e) Booster
(f) Impact Shield
(g) Belt Guide Group 1| (h) Lap Belt Guide Group 2/3
(i) Shoulder Belt Guide
(j) Side Impact Protection
(k) Latch-Connect-Hooks
(l) Latch-Adjuster
(m) ISOFIX-Anchorage-Points
---|---

INITIAL ASSEMBLY

Connect the backrest (b) to the booster (e) by hooking the guide lug on the axis of the booster. The backrest (b) is then folded forward. Place the impact shield (f) on the booster (e).

THE CORRECT POSITION IN THE VEHICLE

The child seat with stored latch-connect-system can be used on all vehicle seats with automatic three-point safety belts approved in the vehicle manual for “universal” use.
A “semi-universal” certification is given to restraint systems that are connected to the car through the latch-connect-system. For this reason, the latch-connectsystem can only be used in certain vehicles. Please refer to the enclosed vehicle type list for approved vehicles. You can obtain the most up- to-date version from www.cybex-online.com.
Above a child’s stature of 135 cm, the compatibility between the Pallas B-Fix and your vehicle might be reduced. Please review the vehicle type list to check whether the child seat can be used in all headrest positions without restrictions.
In exceptional cases, the child car seat may also be used on the front passenger seat. Always comply with the recommendations of the vehicle manufacturer.

INSTALLING THE CHILD SEAT IN THE VEHICLE

Always ensure that…
• the backrests in the vehicle are locked in their upright position.
• when installing the child seat on the front passenger seat, adjust the vehicle seat as far back as possible without affecting the belt routing.
Elongate the straps of the latch-connect-system by using the latch-adjuster (l).
Attach the latch-connect-hooks (k) to the ISOFIX-anchorage-points (m).
Tighten the latch-connect-system by pulling the strap on the adjuster until the position of the child seat is adjusted correctly.
Ensure that the entire surface of the backrest of the child seat (b) is placed against the backrest of the vehicle seat.
? If the headrest of the vehicle is in the way, pull it upwards to its furthest extent or remove it completely (except rear-facing vehicle seats).
Ensure the seat is secure by trying to pull it out of the ISOFIX-anchorage-points (m).
In case the seat is used without latch-connect-system, it can be stored away on the bottom of the seat.
? Using the latch-connect-system, you can fix the CYBEX Pallas B-fix to the vehicle, thereby increasing your child’s safety. The child still needs to be secured with the three-point belt of your vehicle and the impact shield for Group 1.

REMOVING THE CHILD SEAT FROM THE VEHICLE
Perform the installation steps in the reverse order.

Release the tightened straps using the latch-adjuster (l).
Disconnect the latch-connect-hooks (k) on both sides.
Remove the child seat.
You can store the latch-connect-system in the booster of the child seat.

ADJUSTING THE HEADREST

The headrest (c) can be adjusted by using the headrest height adjuster (d) at the back of the headrest (c). Adjust the headrest so that max. 2 cm (approx. 2 finger’s width) remain between the child’s shoulder and the headrest (c).
? The height of the headrest can still be adjusted while the seat is installed in the car.

CORRECT INSTALLATION MODE

Installation mode| Group 1
9 ‒ 18 kg| Group 2/3
15 ‒ 36 kg
---|---|---
with impact shield| without impact shield
Installation| |

SECURING THE CHILD WITH IMPACT SHIELD – GROUP 1 (9–18 KG)

Insert the impact shield (f). The side flaps of the impact shield (f) fit exactly between the arm rests and seating surface of the booster.
Pull out the entire length of the vehicle seat belt.
Place the lap belt over the designated red belt routing on the impact shield (g).
Lock the vehicle seat belt into the belt buckle. It must lock in place with an audible “CLICK”.
Tighten the lap belt by pulling the shoulder belt backwards.
Feed the shoulder belt in parallel with the lap belt back into the belt routing (g) and pull the shoulder belt tight. Ensure that both parts of the belt cover the entire width of the impact shield (f) in the belt routing (g).
Feed the shoulder belt tightly through the belt routing of the impact shield (g) until it is clamped inside the belt guide.
Put the shoulder belt between headrest (c) and backrest (b). The shoulder belt does not need to be guided through the shoulder belt guide (i).

SWITCH FROM GROUP 1 TO GROUP 2/3
Remove the impact shield (f), as soon as your child weighs 18 kg.
? Note that switching from group 1 to group 2/3 is not permitted if your child weighs less than 15 kg. Keep the impact shield in a safe and secure place.

SECURING THE CHILD WITHOUT IMPACT SHIELD – GROUP 2/3 (15–36 KG)

Route the vehicle seat belt around your child and insert the belt tongue into the belt buckle. It must lock into place with an audible “CLICK”.
Place the lap belt in the red coloured lap belt guides (h) of the child seat.
Pull the shoulder belt to tighten the lap belt.
On the side of the car seat next to the belt buckle, the shoulder belt and the lap belt must be inserted together in the lap belt guide (h).
Feed the shoulder belt through the shoulder belt guide (i) until it is inside the belt guide.
Ensure that the shoulder belt runs across your child’s clavicle and does not touch your child’s neck. If necessary, adjust the height of the headrest (c) to change the position of the belt.

REMOVING AND REATTACHING THE SEAT COVER
The cover of the child seat consists of four parts (headrest, backrest, booster and impact shield). These are held in position at several places by pressstuds. Once all studs have been released, the single parts of the cover can be removed.
In order to put the covers back on the seat, follow the removal instructions in the reverse order.
? The cover may only be washed at 30 °C with a delicate wash program otherwise it may result in discolouration of the cover fabric. Please wash the cover separately from other laundry and do not dry in the dryer or in direct sunlight!

MANUFACTURER’S WARRANTY AND DISPOSAL REGULATIONS

CYBEX GmbH (Riedingerstr. 18, 95448 Bayreuth, Germany) gives you 3 years warranty on this product. The warranty is valid in the country, where this product was initially sold by a retailer to a customer. The contents of the warranty and all essential information required for the assertion of the warranty can be found on our homepage go.cybex-online.com/manufacturer- warranty-car-seats. If a warranty is shown in the article description, your legal rights against us for defects remain unaffected.
Please observe the waste disposal regulations in your country.

INFO@CYBEX-ONLINE.COM
WWW.CYBEX-ONLINE.COM
WWW.FACEBOOK.COM/CYBEX.ONLINE
CYBEX GmbH
Riedingerstr. 18 | 95448 Bayreuth
Germany