BEMA 1013813 Bluetooth DAB Marine Audio Owner’s Manual
- June 16, 2024
- BEMA
Table of Contents
BEMA 1013813 Bluetooth DAB Marine Audio
INSTALLATION
Notes:
- Choose the mounting location where the unit will not interfere with the normal driving function of the driver.
- Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.
- Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
- Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.
- Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.
- Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.
Mounting
Once a suitable location has been determined, drill the hole and secure the
stereo using the metal mounting bracket. If the bracket needs to be shortened
, remove the appropriate number of breakaway segments using a pair of pliers.
WIRING CONNECTION
ISO CONNECTION
OPERATION
LOCATION OF KEYS
- BAND / PTY button
- Power/SEL button
- MODE/TA/AF button/BT
- TFT
- IR SENSOR
- Seek up button
- Seek down button
- VOL +
- VOL –
- MUTE button
- Play/pause button/SAVE
POWER ON/OFF THE UNIT
Press the button to turn on/off the unit.
MAIN MENU
Press and hold SETUP/ENTER button on the remote control for 2 seconds ,Then
Press “ ” button on the remote control will enter this MAIN menu(see below
picture).
Then Press “ ”button on the remote control or “ / ” on the front panel to select desired item then press ENTER/SETUP button or button of the front panel to setting corresponding item.
SETUP
Press and hold ENTER/SETUP button on the remote control for 2 seconds will
show the SETTUP menu. See below:
Press “ ”button on the remote control or ” / ” on the front panel to select System /Audio/Video/Default item. Then press ENTER/SETUP button or button of the front panel to enter corresponding item.
(Press “ ” button on the remote control or BND button on the front panel to exit to previous menu.)
SYSTEM SETTINGS
Press “ ” button on the remote control or ” / ” on the front panel to select OSD Language/Time/Radio Area/Beep. Then press ENTER/SETUP button or button of the front panel to enter corresponding item.
-
OSD Language:
Now It has English only.
-
Time
Press “ ” button on the remote control to select adjusting hour or minute. Then press “ ” button on the remote control to adjust correct time. Press ENTER/SETUP button exit this item.
-
Radio Area
Press “ ” button on the remote control to select Europe/America.
-
Beep
Press “ ” button on the remote control to select on/off.
AUDIO SETTINGS
- V surround
Press “ ” button on the remote control to select Off/Concert/Church/Soft/Wide/Live.
Press “ ” button on the remote control or BND button on the front panel to exit to previous menu.
VIDEO SETTINGS
Press “ ” button on the remote control or ” / ” on the front panel to select Aspect ratio/Adjust. Then press ENTER/SETUP button to enter corresponding item.
-
Aspect ratio
Press “ ” button on the remote control to select 4:3 pan scan/16:9. -
Adjust
Press “ ” button on the remote control to select Brightness/Contrast/Hue/Saturation/ Sharpness.
In every item using “ ” button to adjust and press ENTER/SETUP button to exit.
- Default SETTINGS
When selecting default function. Press ENTER/SETUP button to reset to default.
RESET FUNCTION
Press and hold button for 6 seconds to active the RESET function. Also in
setup menu when you select the Default item and press ENTER/SETUP button. It
will active the reset function. The RESET function is to be activated for the
following reasons:
Initial installation of the unit when all wiring is completed.
OPERATION Error symbol on the display.
Once the reset button is pressed. All the memory’s information will be lost!
SLIGHTFOG AFTER OPERATION
Normal in colder weather. Allow radio to run for
1-2 hours, This will burn off moisture.
RADIO OPERATION
-
SWITCHING TO THE RADIO MODE Press MODE button or in the main menu to select RADIO mode. The following information will appear on the display.
-
SELECTING THE FREQUENCY BAND Shortly press BAND button to select desired band. The reception band will change in the following order:
You can select Europe or American Band in Radio Area item of the SETUP menu.
-
Selecting Frequency
During radio mode. Shortly press button will activate automatic seek function. It will search up/down a station automatically.
Press and hold / button for 2 seconds till “MANUAL” appear on the display. The manual tuning mode is selected. In this mode you can turn up/down a step frequency one by one till searched a station. If both buttons have not been pressed for 5 seconds, it will return to seek tuning mode and “AUTO” appears on the display. -
4. Automatic Story & Program Scanning:
- Program scanning Shortly press AMS button on the remote control to scan preset station which is stored in number 1~6 buttons . And it will hold at each station for about 5 seconds.
- Automatic memory storing
Press and hold AMS button on the remote control for 2 seconds. The radio searches from the 87.5 MHz frequency and checks the signal strength until one cycle search is finished. And then some strong stations are stored into the corresponding preset button. In the first cycle it will in LOCAL mode to receive the stronger station. If it stored stations is not full the preset button. It will searching stations in 2nd cycle in DX mode.
-
Manually store station and recall preset station
-
Remote control operation: Received a station, Press one of the preset button (1~6) for 2 seconds. The current station will be stored into the number button. Shortly press preset button (1~6) you can listen to the corresponding station.
-
Front panel operation: Received a station, Press and hold the button till show SAVE P1 on the display. Press to change the preset number then press button. The current station will be stored into the number button. Shortly press button you can listen to the preset station 1~6. (From preset station 1 to preset station 6).
-
Stereo on/off:
Press ST button on remote control to select mono or stereo mode. Sometimes when the signal is not good. If you change it to MONO mode the noise will be reduced. Also you can turn it on/off in SEL menu. -
Local on/off:
Press LOC button on the remote control to select LOC or DX(distance) mode. In LOC mode the unit will reduce the receiving sensitivity when you search station. That means you can receive the station that sound is good. It will ignores the station that sound is not good. In DX mode it will increase the receiving sensitivity when you search the station. That means you can receive more stations. Also you can turn it on/off in SEL menu.
USB OPERATION
-
Playing USB
When insert an USB into the USB jack. The unit will search the MP3/ WMA files and start to play.
-
Pause playback
When playing audio/video content, press the button to pause the playback, press again to resume normal playback. -
Select Chapter/Track
Press the button during playback to select the last or next chapter/track to. -
Stop playback
When playing audio/video content, press the button on the remote controller or BND button of the panel to stop the playing. -
Back to the playing list
a) Remote control operation:
When playing audio/video content, press the button on the remote controller to stop the playing and back to the playing list.
Press “ ” button to select desired song then press ENTER/SETUP button to play.
( note : Press button will change the page of the list).
Press and hold button will back to the previous folder.
Press the button to select the , and . press the button to change to right side. Then Press “ ” button to select desired folder and Press ENTER/ SETUP button to enter the folder. Press “ ” button to select desired song then press ENTER/SETUP button to play.
b) Front panel operation:
When playing audio/video content. Press BND button will back to the playing list. Press BND button again will back to the previous folder. In root press BND button will enter the left side.
Press vol +/- to select the , and . Press back to the right side. Press button to change the page of the playing list.
Press VOL+/- to select the folder or file. Press button to enter the folder or start the playing.
Remark : The icon is for audio files; the icon is for image files; the icon is for video files.
: Tap it to pause playback
: Tap it to stop playback
: Tapping one of them can switch on between the speed levels of fast backward or forward.(Except image mode.)
: Tapping one of them can select next or previous chapter/track. -
Select Chapter/Track with number buttons When playing audio/video content, press the 0~9 buttons on the remote controller to directly select and play the track/chapter. Press 10- /10+ button will backward/fast forward to 10 files to play.
-
Playback with speed
During normal playback, press the button on the remote controller continuously to fast forwards or backwards. During speed playback, press button to resume normal playback.
Also press and hold the button of the panel will active the reverse fast forward fast function. -
Playback in Scan mode.
a. When playing audio, press the INT button to play the previous 10 seconds part of each track. Press the INT button again to resume normal playback.
b. When playing video/image sources, the INT button is not available. -
Playback in Random
When playing video/audio content, press the RDM button to turn on/off random function. -
Playback in RPT
When playing video/audio content, press the
RPT button to select RPTONE/RPT DIR/RPT ALL.
RPTONE: Repeat the same file.
RPT DIR: Repeat all the file of the folder.
RPT ALL: Repeat all file of the USB. -
Playback in Image mode When displaying the root menu,
Press the direction buttons to select your desired FOLDER, then press the ENT or button to open the FOLDER, or play the selected file. When displaying the root menu, you can also use the number buttons to select the serial number of the file and play the file.
During IMAGE playback, press one of the buttons to change the angle of viewing picture that is displaying as follows:
:90 degree cw; :90 degree ccw;
During IMAGE playback, press the button to Pause playing, Press button *During IMAGE playback, the following buttons are not available: RDM, INT.
AV IN OPERATION
Switching to AV IN mode
The AV INPUT jacks is on the back side.
When you connect an audio/video signal through the AV input. Press MODE button
or you can choose from the main menu to select AV in mode.
The main menu of the AV IN mode:
OTHER FUNCTION
-
Equalization
Repeatedly press EQ button on the remote control to select the equalization mode. There are four kinds of mode as below: -
MUTE
Press MUTE button to muting the audio output.
Press it again to recover output. -
LOUD
Press and hold LOUD button on the remote control to turn on/off the LOUD function. -
SEL menu
Repeatedly press SEL button on the remote control will show the SEL menu as below:
Bass—Treble—Balance—Fader—EQ—Loud —LOC—Stereo—Tavol—Brightness— Contrast—Hue—Saturation—Sharpness—Vol In every item you can use button to adjust the desired value. -
SCAN
In RADIO mode. Press SCAN button on the remote control to enter scan mode, the unit will scan to higher frequency station and keep on each station for 5 seconds around. -
OSD
In USB playing press OSD button on the remote control it will turn on/off some information.
BLUETOOTH OPERATION
- PRE-PAIR FOR BLUETOOTH OPERATION
- When use Bluetooth, please make sure the mobile phone supports Bluetooth function.
- For the different kind of mobile phone, Bluetooth emissive power has some difference. To get the best conversation quality, it is commended that the distance between the mobile phone and the unit is within 3m. And please don’t put any metal object or any obstacle between the path of the mobile phone and the unit.
- PAIRING
- On the mobile phone, select the Bluetooth set up. (Please refer to the instruction manual of your mobile phone on how to operate Bluetooth.)
- “CAR KIT” should appear in the list on your mobile phone, please select “Car KIT”. and then input “0000” if it needs a password.
- When successful paired, the BT mark will be displayed on LCD.
- Bluetooth audio (A2DP function) Press MOD key to switch to BT mode.
Then turn on the music player of your mobile phone and playing a song. The sound will come out from the speaker of the unit. Press key of the front panel to pause/play the song. Press button or button to select next/previous song.
Note : When there is a phone is coming in. The music will be muted. When the phone call is hanged. The music will be resumed.
RDS (RADIO DATA SYSTEM) OPERATION
-
Setting RDS mode
Press AF button shortly on the remote control to switch on/off AF mode. In panel Press an hold MOD button for 2 seconds.
The TA item will show on the display.
Press it shortly again the AF will show on the display. In this moment press VOL+/- button to turn on/off AF function.
Whenever AF is switch on, symbol “AF” appears on the display.
Program name is displayed on receiving a RDS station.
“AF” starts blinking if the broadcasting signal getting worse.
“ALARM” will be displayed when an emergency broadcasting is received, meanwhile sound output level will be adjusted to the preset output level automatically when the volume control is set at minimum. -
Listening to Traffic Announcement
Press TA button shortly on the remote control to switch on/off TA mode. In panel Press an hold MOD button for 2 seconds.
The TA item will show on the display. In this moment press VOL+/- button to turn on/off TA function. When TA mode is on and a traffic announcement is transmitted:
When the unit was in MP3 or AUX IN mode, it will switch temporarily to radio mode. (If in MW band it is can’t switch temporarily to the TA station).
Temporary switch over to an EON linked station when EON detects a traffic announcement on that other program. If the volume level was under the threshold point it will be raised to the threshold point.
When TA mode is on, TA of individual segment is turned on. When a TP station is received, TP of individual segment is turned on.
TA interruption function
The current traffic announcement is cancelled by pressing TA key. EON TA
information was received from current station and the radio switched to that
EON linked station, but no Information could not be received because the EON
linked station is located too far from that area. So the radio is switched
back to current station again. In above operation, a customer listens to a
wrong program or mute sound for a while. The RDS data used are the PI, PS, AF,
TP, TA, EON and PTY data.
PI: Program Identification code Code for identifying programs PS: Program
Service Name Broadcast station name data expressed in alphanumerically
characters AF: Alternative Frequencies Frequency list of broadcasting stations
transmitting the same program.
TP : Traffic Program Identification identification data for traffic
information-broadcasting station
TA : Traffic Announcement Identification Identification data showing
traffic information is being transmitted or not
EON : Enhanced Other Networks Information Broadcasting information on PI,
AF, TP, TA, etc, relating to networks other than the network used for current
reception.
- Using PTY to Select Program
PTY has a speech group and a music group. Press and hold BND button (10) for 2 seconds it will change as below:
PTY SPEECH group—PTY MUSIC group— PTY off
In PTY SPEECH group you can select the program type as below by using button
1~6(remote control). After several seconds it
will searching automatically.
1# button: NEWS/AFFAIR/INFORM
2# button: EDUCATIO/DRAMA/SPORT
3# button: VARIED/CULTURE/SCIENCE
4# button: FINANCE/CHILD REN/WEATHER
5# button: PHONE IN/SOCIAL/RELIGION
6# button: TRAVEL/LEISURE/DOCUMENT
Also you can pressing the VOL+/- button on the panel to select above program.
In PTY MUSIC group you can select the program type as below by using button
1~6. After several seconds it will searching automatically.
1# button: ROCK M /POP M
2# button: LIGHT M/EASY M
3# button: OTHER M/CLASSICS
4# button: COUNTRY/JAZZ
5# button: OLDIES/NATION M
6# button: FOLK M
Also you can pressing the VOL+/- button on the panel to select above program.
DAB OPERATION
-
Press AMS button on remote control for DAB full scan. If there isn’t any station, Scroll display “NO STATION FOUND”.
-
Press / buttons (5/3)button it is station up/down.
Shortly press M1-M6 button(remote control) or button to read M1-M6 station.
If Read Empty Preset, Display “NO SAVED” -
Press and hold M1-M6 button(remote control) to memory the current station to the M1-M6 station.
REMOTE CONTROL
- MODE Press to change the source.
- POWER Press it to turn the unit ON or OFF
- BAND: To select FM1, FM2, FM3, MW1, MW2 radio bands.
- ENTER/SETUP Long press to return to previous menu, short press to enter next menu;
- In case of MENU mode, buttons serves as cursor buttons to select item left/right, ahead/back.
- EQ Press it to select desired audio equalization
- Stop
- SEL Access the Bass, Treble, Balance and Fader setting
- INT Press INT to INTRO each file. Press again to stop intro function.
- Press to pause the playing. Press it again to resume to play
- Press to skip to the next track & press to skip back one track in navigation mode.
- 0-9 Inputs the corresponding number.
- OSD turn on/off some information in USB mode.
- SCAN Scanning Button
- In MP3 mode. Press to search forward rapidly & to search reverse rapidly. In radio mode, use for manual tuning.
- RDM Press it to play all tracks in random order
- RPT Repeat play.
- 10+/10- Digital selecting button, cooperatively used with numeric buttons
- TA: Turn on/off the TA function
- VOL- decrease (-) the volume level.
- PTY Program selection and searching.
- AF Turn on/off the AF function.
- VOL+ decrease (+) the volume level.
- MUTE Press to mute the sound. Press it again to recover the sound.
- AMS In radio mode, press it to activate Automatic Memory Storing/Program Scanning function.
SPECIFICATION
GENERAL
Power Supply Requirements : DC 12 Volts, Negative Ground
Chassis Dimensions : 100 (W) x 100 (D) x 75 (H) Tone Controls
Bass (at 100 Hz) : ±10 dB
Treble (at 10 kHz) : ±10 dB
Maximum Output Power : 4×40 watts
Current Drain : 10 Ampere (max.) (For Normal Power Version)
RADIO
Frequency Coverage 87.5 to 108 MHz
IF 10.7 MHz
Sensitivity (S/N=30dB) 4μV
Stereo Separation >25dB
Frequency Coverage 174.928~239.200 MHz
Sensitivity (S/N=20dB) ≥-100dBuV
Preset stations 18
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>