VS600HD Efficient TV Wall VisualStation

Product Information

Specifications

• Product Name: VS600HD
• Last Update: May 31, 2023

Chapter 1: Before You Start

1.1 Package Contents

Contact your reseller if your package is missing any of the
below contents:

• Main unit x 1
• AC power adapter x 1
• RJ 45 LAN cable x 1
• s10 screws x 10
• s11 screws x 5
• Mounting plate x 1
• Monitor mounting adapter x 1

1.2 Synology VisualStation at a Glance

information,
see System modes and LED indicators.
2| STATUS Indicator| Displays the status of the system. For more information, see
System modes and LED indicators.
3| LAN Indicator| Displays the status of the network connection. For more
information, see Other LED indicators.
4| HDMI Port| Connect a HDMI cable here.
5| LAN Port| Connect a network cable here.
6| USB 3.2 Gen 1 Port| Connect a USB mouse, USB keyboard, or other USB device
here.
7| Audio Out (3.5mm)| Connect an external speaker or earphones to audio output.
8| Audio In (3.5mm)| Connect a microphone to audio input.
9| Power Button| Press to power on your Synology VisualStation. To power off
your Synology VisualStation, press and hold until the POWER LED
turns off. Mode 1: Press and hold until you hear a beep sound to
restore the IP address, DNS server, and password for the admin
account to default.
10| RESET Button| Mode 2: Press and hold until you hear a beep, release the
button immediately, then press and hold again within 10 seconds to
reinstall VisualStation. For detailed information on how to reset
your Synology VisualStation, please refer to this article.
11| Power Port| Connect power cord here.

1.3 System Modes and LED Indicators

There are 4 system modes in Synology VisualStation. The System
modes and their definitions are as below:

button or restarting when you run operations in VisualStation.

Chapter 2: Hardware Components Installation

2.1 Recommended Tools

To install the hardware components, it is recommended to have
the following tools:

• Tool 1
• Tool 2
• Tool 3

2.2 Precautions

Before installing the hardware components, please take note of
the following precautions:

• Precaution 1
• Precaution 2
• Precaution 3

2.3 Safety Instructions

Ensure your safety during the installation process by following
these safety instructions:

• Safety Instruction 1
• Safety Instruction 2
• Safety Instruction 3

2.4 Hardware Setup

Follow these steps to set up the hardware components:

1. Step 1
2. Step 2
3. Step 3

Chapter 3: Initial System Setup

3.1 Check your Surveillance Station Software

Before proceeding with the initial system setup, ensure that you
have the Surveillance Station software installed. If not, please
install it before continuing.

3.2 Connect VS600HD to your Synology NAS/NVR

To connect your VS600HD to your Synology NAS/NVR, follow these
steps:

1. Step 1
2. Step 2
3. Step 3

3.3 Learn More

If you need further assistance with the initial system setup,
refer to the provided documentation or contact our support
team.

Chapter 4: System Maintenance

4.1 Replace the Malfunctioning Fan

If the fan in your Synology VisualStation is malfunctioning,
follow these steps to replace it:

1. Step 1
2. Step 2
3. Step 3

Chapter 5: Troubleshooting

5.1 Troubleshooting Checklist

If you encounter any issues with your Synology VisualStation, go
through this checklist to troubleshoot:

• Checklist Item 1
• Checklist Item 2
• Checklist Item 3

5.2 Common Issues Resolution

Here are some common issues and their resolutions:

• Issue 1: Resolution
• Issue 2: Resolution
• Issue 3: Resolution

5.3 Before You Contact Synology Technical Support

Before contacting Synology Technical Support, make sure to go
through the following steps:

1. Step 1
2. Step 2
3. Step 3

5.4 Contacting Synology Technical Support

If you still need assistance, contact Synology Technical Support
using the provided contact details.

5.5 Getting Information, Help, and Service

If you need additional information, help, or service, refer to
the provided documentation or contact our support team.

FAQ (Frequently Asked Questions)

Q: What should I do if my package is missing some

contents?

A: If your package is missing any contents, please contact your
reseller for assistance.

Q: How do I connect my VS600HD to my Synology NAS/NVR?

A: To connect your VS600HD to your Synology NAS/NVR, follow the
steps provided in Chapter 3, section 3.2 of the user manual.

Q: How can I reset my Synology VisualStation?

A: There are two modes for resetting your Synology
VisualStation. Refer to Chapter 1, section 1.2 of the user manual
for detailed instructions.

Product Manual
VS600HD
Last May 31, 2023

Table of Contents

Chapter 1 Before You Start

2

1.1 Package Contents

2

1.2 Synology VisualStation at a Glance

3

1.3 System Modes and LED Indicators

4

1.4 Other LED Definitions

5

1.5 Hardware Specification

6

1.6 Spare Parts

7

Chapter 2 Hardware Components Installation

8

2.1 Recommended Tools

8

2.2 Precautions

8

2.3 Safety Instructions

10

2.4 Hardware Setup

11

Chapter 3 Initial System Setup

16

3.1 Check your Surveillance Station Software

16

3.2 Connect VS600HD to your Synology NAS/NVR

16

3.3 Learn More

17

Chapter 4 System Maintenance

18

4.1 Replace the Malfunctioning Fan

18

Chapter 5 Troubleshooting

26

5.1 Troubleshooting Checklist

26

5.2 Common Issues Resolution

26

5.3 Before You Contact Synology Technical Support

29

5.4 Contacting Synology Technical Support

29

5.5 Getting Information, Help, and Service

30

1

Chapter 1 Before You Start
Thank you for purchasing this Synology product! Before setting up your new Synology VisualStation, please check the package contents to verify that you have received the items below. Also, make sure to read the safety instructions carefully to avoid harming yourself or damaging your Synology VisualStation.
Notes:
All images below are for illustrative purposes only, and may differ from the actual
product.

1.1 Package Contents
Contact your reseller if your package is missing any of the below contents:

Main unit x 1

AC power adapter x 1

RJ 45 LAN cable x 1

s10 screws x 10

s11 screws x 5
2

Mounting plate x 1

Monitor mounting adapter x 1

1.2 Synology VisualStation at a Glance

No.

Name

POWER

1

Indicator

STATUS

2

Indicator

3 LAN Indicator

4 HDMI Port

5 LAN Port

USB 3.2 Gen 1

6

Port

Description Displays the power status of the system. For more information, see “System modes and LED indicators”. Displays the status of the system. For more information, see “System modes and LED indicators”. Displays the status of the network connection. For more information, see “Other LED indicators”. Connect a HDMI cable here. Connect a network cable here.
Connect a USB mouse, USB keyboard, or other USB device here.

3

7

Audio Out
3.5mm)

8

Audio In
3.5mm)

Connect an external speaker or earphones to audio output. Connect a microphone to audio input.

9 Power Button

Press to power on your Synology VisualStation.
To power off your Synology VisualStation, press and hold until
the POWER LED turns off.

Mode 1 Press and hold until you hear a beep sound to restore
the IP address, DNS server, and password for the admin
account to default.

10 RESET Button

Mode 2 Press and hold until you hear a beep, release the button immediately, then press and hold again within 10

seconds to reinstall VisualStation.

For detailed information on how to reset your Synology

VisualStation, please refer to this article.

11 Power Port

Connect power cord here.

1.3 System Modes and LED Indicators

System modes definitions
There are 4 system modes in Synology VisualStation. The System modes and their definitions are as below:

System mode

Definition

Powering on

Synology VisualStation is powering on when you press the power button or restarting when you run operations in VisualStation.
During the boot up process, the device also performs hardware initialization, such as hardware reset or BIOS initialization.

Shutting down

Synology VisualStation is shutting down as a result of pressing the power button or operation in VisualStation.

VisualStation is ready for use

VisualStation is fully functioning, and users can sign in.

Powered off

Synology VisualStation is powered off.

4

Identify System Modes
You can identify the system mode through the POWER and STATUS LED indicators. Please refer to
the table below for more details.

System Mode
Powering on Shutting down VisualStation not
ready VisualStation is ready
for use Powered off

POWER LED Green Blinking Blinking
Static
Static Off

STATUS LED

Green

Orange

Off Static

Off Off/Static1

Blinking

Off/Blinking1

Static Off

Off/Static1 Off

Notes: If the STATUS LED remains static orange or continuously blinks orange, this indicates
there are system errors such as fan failure or system overheating.

1.4 Other LED Definitions

LED Indicator
LAN
Rear 1GbE LAN
(on left side of jack)
Rear 1GbE LAN
(on right side of jack)

Color

Status

Green

Static
Blinking

Off

Green

Static
Blinking

Off

Green

Static

Off

5

Description
Network connected Network active No network
Network connected Network active No network
1 Gbps connected
10 Mbps connected/100 Mbps connected/No network

1.5 Hardware Specification

Item CPU RAM
External Port
LAN Port Size H x W x D (mm)
Weight (kg)
Agency Certification
Environment Requirement

VS600HD
Intel Celeron J4125
DDR4 4 GB
· USB 3.2 Gen 1 x 2 · HDMI Port x 2
· Audio Out 3.5mm) x 1 · Audio In 3.5mm) x 1
1GbE RJ 45 x 1
41.84 x 150 x 150
0.36
· FCC Class B · CE Class B · UKCA · BSMI Class B · EAC · VCCI · RCM · KC
· Line voltage: 100V to 240V AC · Frequency: 50 / 60Hz
· Operating Temperature:
Chassis: 4°F to 104°F 20°C to 40°C Adapter: 32°F to 104°F 0°C to 40°C
· Storage Temperature: 4°F to 140°F 20°C to 60°C · Relative Humidity: 5% to 95% RH

Notes:
Model specifications are subject to change without notice. Refer to Synology website for the latest information.

1.6 Spare Parts
Refer to Spare Parts if you need to replace system fans or power supply units.

Model Name

Picture

Description

6

FAN 40 10_1 Adapter 36W Set

System Fan 40 40 10 mm
Adapter 36W Wall Mounted Level VI

7

Chapter 2 Hardware Components Installation
2.1 Recommended Tools
This section lists the required and optional tools used in the installation procedures. Phillips #2 screwdriver Phillips #0 screwdriver (for chassis only) A VESA-compliant monitor (optional)
Notes:
If an automatic screwdriver is used, set its torque reading to 4.0 (+/ 0.3 kgf-cm.
2.2 Precautions
Before installing or removing any components in your Synology VisualStation, review all safety information.
8

Caution:
Leaving stray or loose screws inside your Synology VisualStation may severely
damage its components. Avoid dropping any metallic objects into the VisualStation,
such as paper clips and hairpins.
Do not pull a cable by its connector or its pull tab when disconnecting it. Certain
cables have connectors with locking tabs or thumb-screws that must be released before disconnecting the cable. When disconnecting a cable, keep it evenly aligned to avoid bending the connector pins. When connecting a cable, make sure that the ports and the connectors are correctly oriented and aligned. Make sure that your Synology VisualStation is working correctly before installing
optional hardware components. If your Synology VisualStation is not working correctly, see the “Troubleshooting” chapter to do basic troubleshooting. If the problem cannot be solved, see the section “Getting information, help, and service” for more
information.
Always carefully handle system components (such as system boards) by the edges or the frame. Do not touch solder joints, pins, or exposed circuitry. Do not place parts and other components (such as system boards) on the top cover of
the Synology VisualStation or other metal surfaces. Only specific Synology VisualStation support the hot-swapping of components and are designed to operate safely while it is turned on.
Before working inside your Synology VisualStation
Power off the Synology VisualStation, including all attached peripherals.
Disconnect the Synology VisualStation from the electrical outlet and disconnect the
peripherals.
After working inside your Synology VisualStation
Reconnect the peripherals and connect the Synology VisualStation to an electrical outlet. Power on the attached peripherals and then power on the Synology VisualStation.
Preventing electrostatic discharge
Static electricity discharge from a finger or other conductors might lead to system halt, loss of data, or other damages to system boards or other static- sensitive components. This type of damage may also reduce the life expectancy of the Synology VisualStation. Prevent exposure to static electricity by doing the following:
9

Avoid hand contact by transporting and storing hardware components in static- safe containers. Keep electrostatic-sensitive hardware components in their containers until they arrive at static-free workstations. Place hardware components on a grounded surface or touch them before removing them from their containers. Avoid touching joints, pins, leads, or circuitry. Always be properly grounded when touching a static-sensitive hardware component or assembly. When handling a hardware component, carefully hold it by the edges or the frame. Use an electrostatic-discharge wrist strap or other ground systems. The Synology VisualStation should be placed on an anti-static mat ESD mat). The Synology VisualStation will provide standby power when it is connected to AC power even if it is powered off. Damage can be done to the VisualStation if a conductor is accidentally touched and parts are short- circuited under this condition. Before removing the top rear cover, make sure the AC power supply is disconnected.
2.3 Safety Instructions
Keep away from direct sunlight and chemicals. Ensure a stable environment with no abrupt changes in temperature or humidity.
Place the unit right side up at all times.
Keep the unit away from liquids.
Before cleaning, unplug the power cord(s) and use a damp cloth to wipe the surface. Do not use chemical aerosol cleaners.
To prevent the unit from falling over, do not place it on carts or any unstable surfaces.
The power cord(s) must be plugged into the correct power supply voltage. Ensure that the AC voltage provided is correct and stable.
Warning, electric shock hazard. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.
10

There is a risk of explosion if the battery is replaced with an incorrect type.
Dispose of used batteries appropriately.
Power cord(s) must be plugged into a socket-outlet with earthing connection.
Keep your body parts away from a moving fan.
System reliability guidelines
To guarantee adequate system cooling and reliability, follow the system reliability guidelines listed below.
Leave adequate space around the Synology VisualStation to ensure that its cooling system works well. Leave approximately 50 mm 2 inches) of open space around the front and rear of
the Synology VisualStation. Do not place objects in front of the fans. For proper cooling and airflow, install the Synology VisualStation cover before you power it on.
Operating a Synology VisualStation without its cover might damage Synology VisualStation components.
If your Synology VisualStation has air ducts or air baffles, do not remove them while the
Synology VisualStation is running. Operating the Synology VisualStation without the air ducts or air baffles might cause your system to overheat. Opening or removing the Synology VisualStation top cover while the system is powered on may expose you to a risk of electric shock.
If you must power on the Synology VisualStation without its top cover, ensure that no one is near the Synology VisualStation and that no tools or other objects have been left inside it. Do
not operate the system without Synology VisualStation cover for a duration exceeding five minutes.
2.4 Hardware Setup
Turn the VS600HD upside-down and use an s10 screw to lock the mounting plate to the
bottom of the device.
11

With the groove facing outwards, attach the monitor mounting adapter to the back of the screen using an s11 screw.
The monitor mounting adapter is compatible with both MIS D 75 and MIS D 100 type VESA compliant surfaces.
12

The two types of adapters are shown below: Install the MIS D 100 mounting adapter as shown in the diagram below by screwing the s11 screws into the indicated positions.
13

Use s10 screws to install the VS600HD to the mounting plate. Connect the HDMI, LAN cable, mouse/keyboard, and power cables to the VS600HD. When
done, press the power button to turn the device on.
14

Once the installation is complete, you can start configuring your Synology VisualStation.
15

Chapter 3 Initial System Setup
After hardware setup is complete, please check your Surveillance Station software before signing into the Synology VisualStation.
3.1 Check your Surveillance Station Software
Before connecting VS600HD to your Synology NAS/NVR product, please ensure that Surveillance Station version 9.1.2 or above is installed on your Synology NAS/NVR product in order to utilize all new features. Sign in to your Synology NAS/NVR. Go to Package Center. Find and update Surveillance Station. The version number is displayed.
3.2 Connect VS600HD to your Synology NAS/NVR
Once the VS600HD is connected to the network and booted up, you can proceed to connect it to your Synology NAS/NVR product. Sign in with an administrator’s account to get full access to all
16

features and functions available in Surveillance Station.
3.3 Learn More
Your VS600HD is now ready for action. For more information or online resources about your VS600HD, please visit Synology’s official website, which contains step-by-step tutorials and
frequently asked questions.
17

Chapter 4 System Maintenance
4.1 Replace the Malfunctioning Fan
If the cooling fan located inside the Synology VisualStation malfunctions, please follow the steps below to replace the malfunctioning fan.
Caution:
We recommend that you wear work gloves and operate with care to avoid injury during
the process.
To remove the malfunctioning fan
Shut down your Synology VisualStation. Disconnect all cables from your Synology VisualStation to prevent possible damage.
Remove the four rubber pads at the bottom of the device.
18

Use a Phillips #0 screwdriver to remove the four screws under the rubber pads. As shown in the figure below, there is a groove on the edge of the back cover. Use a flathead
screwdriver to pry open the back cover at the groove.
19

Do the same at the other side of the back cover. Carefully detach the back cover from the device along the seam. Open the back cover in the direction as indicated in the figure below.
20

Open the back cover completely and place to the side as indicated in the figure below.
Notes:
When you remove the case, sensitive internal components are exposed. Avoid touching anything other than the fan. Unplug the fan connector.
Use a Phillips #2 screwdriver to remove the four screws securing the fan to the back cover, then remove the malfunctioning fan.
21

To install a new fan
Install the replacement fan. The fan must be installed in the direction specified in the figure below.
22

Use the four screws to secure the fan to the back cover. Plug in the fan connector.
23

Re-install the back cover in the direction as shown below. As shown in the figure below, first install side a of the back cover, then press downwards on
side b.
Gently press down on the back cover on all four sides. You should hear a click when it is securely installed.
24

Screw the four screws back into place. Reinstall the four rubber pads.
25

Chapter 5 Troubleshooting
CAUTION
You should only perform troubleshooting and repairs as authorized or directed by the Synology Technical Support team.
Notes:
This chapter describes possible issues that may occur. Not every issue will occur on your Synology VisualStation. Please refer to the corresponding sections for troubleshooting steps specific to the issue that has occurred.
5.1 Troubleshooting Checklist
Before doing any troubleshooting or repair tasks, use the following checklist to ind possible
causes for hardware issues on your Synology VisualStation.
Remove all USB drives before powering on the Synology VisualStation. Is the Synology VisualStation connected to a functional AC power outlet? Is the Synology VisualStation turned on? Is the POWER LED light on? Is the STATUS LED light on?
Verify that all cables are not loose or incorrectly connected.
Are you operating the latest version of VisualStation?
5.2 Common Issues Resolution
The following issues are discussed in this section: Unable to connect to the network
Unable to recognize external USB devices Unable to finish powering on (power LED is blinking continuously)
No power after pressing the power button
26

Unable to connect to the network
Restart the system and confirm that the network status and configuration are correct. Check whether the network cable is loose or damaged, and replace it with a working network
cable. Connect the network cable to another port on the switch or hub. Connect the network cable directly to a PC to confirm whether the Synology VisualStation can
be connected to normally. Check the interior and exterior of the network port for dust or damage.
Check the interior of the network port for damaged or skewed pins.
If, after following the above troubleshooting steps and the issue is still unresolved, contact Synology Technical Support for further assistance.
Unable to recognize external USB devices
Do a visual inspection and check whether the USB port is rusted, which may cause a bad connection.
Check that the external USB device is compatible with your Synology VisualStation. Do a visual inspection and check whether there is foreign matter inside the port. Check that the power supply for the external USB device is plugged in and provides power. Swap the inoperative USB device with one that has been confirmed to work properly. If, after following the above troubleshooting steps and the issue is still unresolved, contact
Synology Technical Support for further assistance.
27

Unable to finish powering on (power LED is blinking continuously)
Statically discharge yourself. Make sure your Synology VisualStation is powered off. Remove all attached external devices and power up the system .
Check the status of the power button LED light. For more information on LED definitions, please see “System modes and LED indicators”.
Notes: Being able to ping the unit doesn’t mean anything of note other than that the LAN ports are functional. To properly do the above testing, ensure that the power LED goes
static and does not continue blinking.
No power after pressing the power button
Do the following basic environmental check: Confirm that the power cord(s) is functioning normally and that it is not damaged. Confirm that the power cord(s) is properly plugged at both the power socket and the
Synology VisualStation.
Confirm that the AC power supply meets the voltage requirements 110V – 220V . If a UPS is connected to the Synology VisualStation, disconnect it temporarily, and use AC power
instead.
Remove all external I/O devices (such as external hard disks/USB/LAN . Retain only the power
supply and confirm that the Synology VisualStation can power on properly.
If the Synology VisualStation is still unable to power on after doing the environmental check,
follow the steps below and do an internal check of your Synology VisualStation. Remove the power cord(s) and remove the top cover.
Confirm that the LED cables are properly plugged in. Confirm that PSU connectors are properly plugged in. Check that there is no dust buildup on internal components; if there are, it needs to be
cleaned. Reconnect the power cord(s) and try to power on the Synology VisualStation again.
If, after following the above troubleshooting steps and the issue remains unresolved, contact
Synology Technical Support for further assistance.
5.3 Before You Contact Synology Technical Support
28

Before you contact Synology Technical Support, follow the below instructions to try to solve the
issue: Use the troubleshooting information in this manual.
Follow the instructions in the “Troubleshooting checklist”. Check for the updated information, new device drivers, and hints and tips on the Synology Knowledge Center. If possible, be at your product when you contact Synology Technical Support and have the following information available: Product Model Name Serial numbers of your Synology products Description of the problem Exact wording of any error messages Hardware and software configuration information
5.4 Contacting Synology Technical Support
During the warranty period, you can get help and information through the Synology Technical Support. Trained service personnel are available to assist you in determining a hardware problem and deciding what action is necessary to fix the problem. The warranty does not cover the following:
Replacement or use of parts not manufactured for or by Synology or non- warranted Synology parts Identification of software problem sources Installation and maintenance of application programs If it is determined that replacement services are necessary, please contact the local reseller or distributor where you purchased the product for further assistance. Synology does not provide direct replacement services outside North America.)
Notes:
For more information about on Synology’s warranty policies, please refer to this article.
5.5 Getting Information, Help, and Service
Synology publishes a wide range of supporting documentation.
29

In Knowledge Base, you will find useful Help and FAQ articles, as well as video tutorials, breaking up processes into handy steps. Also, you can find User’s Guides, Solution Guides, brochures, and White Papers. Experienced users and administrators will find answers and guidance in Developer Guides. Got a problem and unable to find the solution in our official documentation? Search hundreds of answers by users and support staff in Synology Community or reach Synology Technical Support through the web form, email, or telephone.
30

SYNOLOGY, INC. END USER LICENSE AGREEMENT
IMPORTANT­READ CAREFULLY: THIS END USER LICENSE AGREEMENT (“EULA”) IS A LEGAL AGREEMENT BETWEEN YOU (EITHER AN INDIVIDUAL OR A LEGAL ENTITY) AND SYNOLOGY, INC. (“SYNOLOGY”) FOR THE SYNOLOGY SOFTWARE INSTALLED ONTO THE SYNOLOGY PRODUCT PURCHASED BY YOU (THE “PRODUCT”), OR LEGALLY DOWNLOADED FROM WWW.SYNOLOGY.COM, OR ANY OTHER CHANNEL PROVIDED BY SYNOLOGY ( “SOFTWARE”).
YOU AGREE TO BE BOUND BY THE TERMS OF THIS EULA BY USING THE PRODUCTS CONTAINING THE SOFTWARE, INSTALLING THE SOFTWARE ONTO THE PRODUCTS OR DEVICE CONNECTED TO THE PRODUCTS. IF YOU DO NOT AGREE TO THE TERMS OF THIS EULA, DO NOT USETHE PRODUCTS CONTAINING THE SOFTWAREOR DOWNLOAD THE SOFTWARE FROM WWW.SYNOLOGY.COM, OR ANY OTHER CHANNEL PROVIDED BY SYNOLOGY.INSTEAD, YOU MAY RETURN THE PRODUCT TO THE RESELLER WHERE YOU PURCHASED IT FOR A REFUND IN ACCORDANCE WITH THE RESELLER’S APPLICABLE RETURN POLICY.
Section 1. Limited Software License. Subject to the terms and conditions of this EULA, Synology grants you a limited, nonexclusive, non-transferable, personal license to install, run and use one copy of the Software loaded on the Product or on your device connected to the Product solely relating to your authorized use of the Product.
Section 2. Documentation. You may make and use a reasonable number of copies of any documentation provided with the Software; provided that such copies will only be used for internal business purposes and are not to be republished or redistributed (either in hard copy or electronic form) to any third party.
Section 3. Backup. You may make a reasonable number of copies of the Software for backup and archival purposes only.
Section 4. Updates. Any software provided to you by Synology or made available on the Synology website at www.synology.com (“Website”) or any other channel provided by Synology that updates or supplements the original Software is governed by this EULA unless separate license terms are provided with such updates or supplements, in which case, such separate terms will govern.
Section 5. License Limitations. The license set forth in Sections 1, 2 and 3 applies only to the extent that you have ordered and paid for the Product and states the entirety of your rights with respect to the Software. Synology reserves all rights not expressly granted to you in this EULA. Without limiting the foregoing, you shall not authorize or permit any third party to: (a) use the Software for any purpose other than that in connection with the Product; (b) license, distribute, lease, rent, lend, transfer, assign or otherwise dispose of the Software; (c) reverse engineer, decompile, disassemble or attempt to discover the source code of or any trade secrets related to the Software, except and only to the extent that such conduct is expressly permitted by applicable law notwithstanding this limitation; (d) adapt, modify, alter, translate or create any derivative works of the Software; (e) remove, alter or obscure any copyright notice or other proprietary rights notice on the Software or Product; or (f) circumvent or attempt to circumvent any methods employed by Synology to control access to the components, features or functions of the Product or Software. Subject to the limitations specified in this Section 5, you are not prohibited from providing any services hosted by Synology NAS server to any third party for commercial purpose.
Section 6. Open Source. The Software may contain components licensed to Synology under the GNU General Public License (“GPL Components”), currently available at http://www.gnu.org/licenses/gpl.html. The terms of the GPL will control solely with respect to the GPL Components to the extent that this EULA conflicts with the requirements of the GPL with respect to your use of the GPL Components, and, in such event, you agree to be bound by the GPL with respect to your use of such components.
Section 7. Audit. Synology will have the right to audit your compliance with the terms of this EULA. You agree to grant Synology a right to access to your facilities, equipment, books, records and documents and to otherwise reasonably cooperate with Synology in order to facilitate any such audit by Synology or its agent authorized by Synology.
Section 8. Ownership. The Software is a valuable property of Synology and its licensors, protected by copyright and other intellectual property laws and treaties. Synology or its licensors own all rights, titles and interests in and to the Software, including but not limited to copyright and any other intellectual property rights.
Section 9. Limited Warranty. Synology provides a limited warrant that the Software will substantially conform to Synology’s published specifications for the Software, if any, or otherwise set forth on the Website, for a period required by your local law. Synology will use commercially reasonable efforts to, in Synology’s sole discretion, either correct any such nonconformity in the Software or replace any Software that fails to comply with the foregoing warranty, provided that you give Synology written notice of such noncompliance within the warranty period. The foregoing warranty does not apply to any noncompliance resulting from any: (w) use, reproduction, distribution or disclosure not in accordance with this EULA; (x) any customization, modification or other alteration of the Software by anyone other than Synology; (y) combination of the Software with any product, services or other items provided by anyone other than Synology; or (z) your failure to comply with this EULA.
Section 10. Support. During the period specified in the Section 9, Synology will make available to you the support services.

Following the expiration of the applicable period, support for Software may be available from Synology upon written request.
Section 11. Disclaimer of Warranties. EXCEPT AS EXPRESSLY SET FORTH ABOVE, THE SOFTWARE IS PROVIDED “AS IS” AND WITH ALL FAULTS. SYNOLOGY AND ITS SUPPLIERS HEREBY DISCLAIM ALL OTHER WARRANTIES, EXPRESS, IMPLIED OR STATUTORY, ARISING BY LAW OR OTHERWISE, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR USE, TITLE AND NONINFRINGEMENT, WITH REGARD TO THE SOFTWARE. WITHOUT LIMITING THE FOREGOING, SYNOLOGY DOES NOT WARRANT THAT THE SOFTWARE WILL BE FREE OF BUGS, ERRORS, VIRUSES OR OTHER DEFECTS.
Section 12. Disclaimer of Certain Damages. IN NO EVENT WILL SYNOLOGY OR ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL OR SIMILAR DAMAGES OR LIABILITIES WHATSOEVER (INCLUDING, BUT NOT LIMITED TO LOSS OF DATA, INFORMATION, REVENUE, PROFIT OR BUSINESS) ARISING OUT OF OR RELATING TO THE USE OF OR INABILITY TO USE THE SOFTWARE OR OTHERWISE UNDER OR IN CONNECTION WITH THIS EULA OR THE SOFTWARE, WHETHER BASED ON CONTRACT, TORT (INCLUDING NEGLIGENCE), STRICT LIABILITY OR OTHER THEORY EVEN IF SYNOLOGY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Section 13. Limitation of Liability. SYNOLOGY’S AND ITS SUPPLIERS’ LIABILITY ARISING OUT OF OR RELATING TO THE USE OF OR INABILITY TO USE THE SOFTWARE OR OTHERWISE UNDER OR IN CONNECTION WITH THIS EULA OR THE SOFTWARE IS LIMITED TO THE AMOUNT ACTUALLY PAID BY YOU FOR THE PRODUCT REGARDLESS OF THE AMOUNT OF DAMAGES YOU MAY INCUR AND WHETHER BASED ON CONTRACT, TORT (INCLUDING NEGLIGENCE), STRICT LIABILITY OR OTHER THEORY. The foregoing disclaimer of warranties, disclaimer of certain damages and limitation of liability will apply to the maximum extent permitted by applicable law. The laws of some states/jurisdictions do not allow the exclusion of implied warranties or the exclusion or limitation of certain damages. To the extent that those laws apply to this EULA, the exclusions and limitations set forth above may not apply to you.
Section 14. Export Restrictions. You acknowledge that the Software is subject to U.S. export restrictions. You agree to comply with all applicable laws and regulations that apply to the Software, including without limitation the U.S. Export Administration Regulations.
Section 15. Termination. Without prejudice to any other rights, Synology may terminate this EULA if you do not abide by the terms and conditions contained herein. In such event, you must cease use of the Software and destroy all copies of the Software and all of its component parts.
Section 16. Assignment. You may not transfer or assign your rights under this EULA to any third party, except for that preinstalled in the Products. Any such transfer or assignment in violation of the foregoing restriction will be void.
Section 17. Applicable Law. Unless expressly prohibited by local law, this EULA is governed by and construed in accordance with the laws of the country, in accordance with which Synology Inc. was organized without regard to any conflict of law principles to the contrary.
Section 18. Dispute Resolution. Any dispute, controversy or claim arising out of or relating to this EULA will be resolved exclusively and finally by arbitration conducted by three neutral arbitrators in accordance with the procedures of the Arbitration Law and related enforcement rules of the country in which Synology Inc. was organized. In such cases, the arbitration will be limited solely to the dispute between you and Synology. The arbitration, or any portion of it, will not be consolidated with any other arbitration and will not be conducted on a class-wide or class action basis. The arbitration shall take place in Taipei and the arbitration proceedings shall be conducted in English or, if both parties so agree, in Mandarin Chinese. The arbitration award shall be final and binding on the parties and may be enforced in any court having jurisdiction. You understand that, in the absence of this provision, you would have had a right to litigate any such dispute, controversy or claim in a court, including the right to litigate claims on a class-wide or class-action basis, and you expressly and knowingly waive those rights and agree to resolve any disputes through binding arbitration in accordance with the provisions of this Section 18. Nothing in this Section shall be deemed to prohibit or restrict Synology from seeking injunctive relief or seeking such other rights and remedies as it may have at law or equity for any actual or threatened breach of any provision of this EULA relating to Synology’s intellectual property rights.
Section 19. Attorneys’ Fees. In any arbitration, mediation, or other legal action or proceeding to enforce rights or remedies under this EULA, the prevailing party will be entitled to recover, in addition to any other relief to which it may be entitled, costs and reasonable attorneys’ fees.
Section 20. Severability. If any provision of this EULA is held by a court of competent jurisdiction to be invalid, illegal, or unenforceable, the remainder of this EULA will remain in full force and effect.
Section 21. Entire Agreement. This EULA sets forth the entire agreement of Synology and you with respect to the Software and the subject matter hereof and supersedes all prior and contemporaneous understandings and agreements whether written or oral. No amendment, modification or waiver of any of the provisions of this EULA will be valid unless set forth in a written instrument signed by the party to be bound thereby.
Powered by TCPDF (www.tcpdf.org)

SYNOLOGY, INC. LIMITED PRODUCT WARRANTY
THIS LIMITED WARRANTY (“WARRANTY”) APPLIES TO THE PRODUCTS (AS DEFINED BELOW) OF SYNOLOGY, INC. AND ITS AFFILIATES, INCLUDING SYNOLOGY AMERICA CORP, (COLLECTIVELY, “SYNOLOGY”). YOU ACCEPT AND AGREE TO BE BOUND BY THE TERMS OF THIS WARRANTY BY OPENING THE PACKAGE CONTAINING AND/OR USING THE PRODUCT. PLEASE BE ADVISED THAT THIS LIMITED WARRANTY DOES NOT APPLY TO THE SOFTWARE CONTAINED IN THE PRODUCTS WHICH SHALL BE SUBJECT TO ITS END USER LICENSE AGREEMENT, AND THAT SYNOLOGY RESERVES THE RIGHT TO MAKE ADJUSTMENTS AND/OR MODIFICATION TO THIS PRODUCT WARRANTY FROM TIME TO TIME WITHOUT PROVIDING PRIOR NOTICE TO YOU. IF YOU DO NOT AGREE TO THE TERMS OF THIS WARRANTY, DO NOT USE THE PRODUCT. INSTEAD, YOU MAY RETURN THE PRODUCT TO THE RESELLER WHERE YOU PURCHASED IT FOR A REFUND IN ACCORDANCE WITH THE RESELLER’S APPLICABLE RETURN POLICY.
PLEASE NOTE THAT SYNOLOGY’S WARRANTY SUPPORTS ARE NOT AVAILABLE IN EVERY COUNTRY, AND THAT SYNOLOGY MAY REFUSE TO PROVIDE THIS LIMITED WARRANTY SUPPORTS TO YOU IF YOU REQUEST SUCH SUPPORTS NOT AT THE COUNTRY AT WHICH THE PRODUCT WAS ORIGINALLY PURCHASED. THE COUNTRY AT WHICH THE PRODUCT WAS ORIGINALLY PURCHASED SHALL BE DETERMINED BASED ON THE SYNOLOGY’S INTERNAL RECORDS.
Local Consumer Protection Laws. For consumers who are covered by applicable local consumer protection laws and regulations, the rights conferred hereby are in addition to all rights and remedies as set forth in such consumer protection laws and regulations.
Section 1. Products
(a) “Products” refer to New Products or Refurbished Products.
(b) “New Product” means the Synology-branded hardware product and Synology- branded accessories contained in the original packaging Customer bought from an authorized Synology distributor or reseller. You may see our “New Product” at Product Support Status.
(c) “Refurbished Product” means all Synology products which have been refurbished by Synology’s affiliate or an authorized Synology distributor or reseller, not including those sold as “as is” or with “no warranty” by anyone.
(d) “Spare Part” means any parts, accessories, components, and other equipment that are installed or incorporated in or attached to the Product.
(e) Other definition: “Customer” means the original person or entity purchasing the Product from Synology or an authorized Synology distributor or reseller; “Online Store” means an online shop operated by Synology or Synology’s affiliate; “Software” means the Synology proprietary software that accompanies the Product when purchased by Customer, is downloaded by Customer from the Web Site, or is pre-installed on the Product by Synology, and includes any firmware, associated media, images, animations, video, audio, text, and applets incorporated into the software or Product and any updates or upgrades to such software.
Section 2. Warranty Period
(a) “Warranty Period”: The warranty period commences on the purchase date is shown on the purchase receipt or invoice to be presented by Customer and ending at the day after the end of the Warranty Period for each New Product. You may obtain information on the Warranty Period for each New Product at Product Support Status. For Spare Part, Warranty Period under normal use is one year (five years for system drives) from the date the Product was purchased. For Refurbished Products or repaired parts, the Warranty Period is the remainder of the Warranty Period of the Product they are replacing, or ninety (90) days from the date the Product was replaced or repaired, whichever is longer. The above Warranty Periods do not apply where Products are marked as sold as “as is” or with “no warranty”. In the event that a valid receipt of purchase of our Product or Product invoice is not presented, or is apparently erroneous or falsified, the Warranty Period for the presented Product shall commence from the manufacturing date in accordance with Synology’s internal records.
(b) “Extended Warranty Period”: For Customer purchasing EW201/EW202 or Extended Warranty Plus optional services for New Products specified in Section 1 (b), the Warranty Period will be extended by two years. For EW201/EW202, you may see the applicable Product models and available regions at EW201/EW202 Extended Warranty. For Extended Warranty Plus, you may see the applicable Product models and available regions at Extended Warranty Plus. Customer can only choose either of the optional services.
(c) “Immediate termination of Warranty Period”: For Synology drive products, the Warranty Period will terminate immediately upon the occurrence of either of the following situations: (a) for solid-state drive, its lifespan wear-out indicator equals or exceeds the limit specified in the “product specifications” of the drive attached with the purchased Product; (b) for all drive products, its temperature record equals or exceeds the operating temperature limit of the drive, which is specified in the “product specifications” attached to the purchased Product.

Section 3. Limited Warranty and Remedies
3.1 Limited Warranty. Subject to Section 3.2, Synology warrants to the Customer that each Product (a) will be free of material defects in workmanship and (b) under normal use will perform substantially in accordance with Synology’s published specifications for the Product during the Warranty Period. Such limited warranty does not apply to the Software contained in the product or purchased by Customer which shall be subject to the accompanying end user license agreement provided with the Product. Synology provides no warranty for Refurbished Product sold as “as is” or with “no warranty”.
The above Limited Warranty is not transferable and is only for the benefit of Customers who directly purchase Products from Synology’s affiliate, resellers, and Synology-authorized distributors. The warranty set forth herein will terminate upon Customer’s sale or transfer of the Product to a third party.
3.2 Exclusions. The foregoing warranties and warranty obligations do not apply to any Product that (a) has been installed or used in a manner not specified or described in the Product, specifications, or its related documents, or in any way misused, abused, or damaged; (b) has been damaged caused by accident, fire, liquid contact, earthquake, other external factor or product use in improper environment; (c) has been disassembled without authorization from Synology; or (d) with cosmetic damage caused by normal wear and tear or otherwise due to the normal aging of the Product, including but not limited to scratches, dents and broken plastic on ports unless failure has occurred due to a defect in materials or workmanship; (e) serial number has been removed or defaced from Product, resulting in not able to identify; (f) has been damaged or out of order because Customer fails to implement any correction, modification, enhancement, improvement or other update made available to Customer by Synology, or because Customer implements, installs or uses any correction, modification, enhancement, improvement or other update made available by any third party; (g) has been damaged, out-oforder, or incompatible due to installation or use with items not provided by Synology other than the hardware, software or other accessory for which the Product is designed.
Please note that each of the above situations shall be subject to the inspection and verification of the Product’s appearance and functions by Synology. Synology may refuse to provide any warranty services, including but not limited to product repair, technical support, and product replacement as described in Section 3.3 to any Product under any of the above situations.
3.3 Warranty Support and Exclusive Remedy. If Customer gives notice of noncompliance with any of the warranties set forth in Section 3.1 within the applicable Warranty Period in the manner set forth below, then, upon verification of the noncompliance by Synology, Synology will, at Synology’s option: (a) use commercially reasonable efforts to repair the Product, (b) provide technical support, or (c) replace the noncomplying Product or part thereof upon return of the complete Product in accordance with Section 3.4 The foregoing sets forth Synology’s entire liability and Customer’s sole and exclusive remedy for any breach of warranty under Section 3.1 or any other defect or deficiency in the Product. Customer will reasonably assist Synology to diagnose and validate any nonconformity with the Product. Please note that the warranty support does not apply to rescue of the data stored in Synology Product or its backup. Customer shall make a backup copy of the stored data before returning the Product to Synology. Synology may remove all information or data in the Product while it performs the warranty services and shall not be responsible for or liable to any data loss therein. In addition, Customer is required to remove any accessories that are not pre-installed, such as adapter card, memory, hard disk drive or solid-state drive as Synology will not be responsible for any loss of unremoved components that are not pre- installed.
3.4 Return. For warranty claims, the Customer must return the complete Product to Synology in accordance with this Section 3.4. Any returned Product which (a) has been disassembled (except under the direction of Synology); or from which (b) the serial number has been removed or defaced, causing inability to identify, or which (c) was damaged on the way of return because of improper packaging (including but not limited to scratches and deformation), will be refused and returned to Customer at Customer’s expense. Any Product must be returned in the same condition as it was received from Synology to the address designated by Synology, freight pre-paid, in packaging sufficient to protect the contents thereof. International shipping may be required depending on the Customer’s location, and Customer shall be responsible for customs duties, clearance, and all other charges related to the replacement service. Customer is responsible for insurance and risk of loss and/or damage with respect to returned items until they are properly received by Synology.
3.4.1 General Replacement Service. Any Product returned by Customer under Section 3.3 must be made in accordance with Synology’s then-current replacement procedures with the purchase receipt or invoice. You may see more information on the replacement procedure at How do I make a warranty claim for my Synology product?
3.4.2 Extended Warranty Plus Service. (Only applicable to the Customer purchasing Extended Warranty Plus) (a) Standard Direct Replacement service: Regarding Standard Direct Replacement service, the Customer must return the nonconforming Product recognized by Synology to the designated return service center at Customer’s expense first. The replacement will not be shipped until the nonconforming Product is received at Synology’s designated return service center. (b) Advanced Direct Replacement service: Regarding Advanced Direct Replacement service, Synology will ship the replacement Product to the address specified by the Customer before the Customer returns the nonconforming Product. Customer must return the nonconforming Product recognized by Synology to the corresponding return service center at Customer’s expense within twenty-eight (28) calendar days from the date when the application is successful and must provide a credit card authorization to serve as security. The credit card authorization will be

canceled after Synology has received the nonconforming Product returned by the Customer. If the Customer has not returned the nonconforming Product within twenty-eight (28) calendar days, Synology is entitled to collect the security in full from the Customer’s credit card and to disable all services related to the serial numbers of the nonconforming Product and the replacement. In addition, Synology reserves the rights to refuse to provide any relevant technical support in the future. The aforementioned measures shall not affect Synology’s legal rights arising therefrom.
3.5 Replacement of New Product or Refurbished Product by Synology. If Synology elects to replace any Product under this Warranty set forth in Section 3.1, then Synology will ship a replacement Product at Synology’s expense via the shipping method selected by Synology after receipt of the nonconforming Product returned in accordance with Section 3.4 and validation by Synology that the Product does not conform to the warranty. Before the shipment of the Refurbished Product to the Customers, they have been verified to strictly comply with Synology’s quality standard. Please note that part of the Refurbished Products would be with certain stain, scratches, or other minor wear and tear. In some countries, Synology may at its own discretion apply the Synology Replacement Service to certain Products, through which Synology will ship a replacement Product to Customer before its receipt of the nonconforming Product returned by Customer (“Synology Replacement Service”).
3.6 Disclaimer of Warranties. THE WARRANTIES, OBLIGATIONS, AND LIABILITIES OF SYNOLOGY AND THE REMEDIES OF CUSTOMER SET FORTH IN THIS WARRANTY ARE EXCLUSIVE AND IN SUBSTITUTION FOR, AND CUSTOMER HEREBY WAIVES, RELEASES AND DISCLAIMS, ALL OTHER WARRANTIES, OBLIGATIONS AND LIABILITIES OF SYNOLOGY AND ALL OTHER RIGHTS, CLAIMS AND REMEDIES OF CUSTOMER AGAINST SYNOLOGY, EXPRESS OR IMPLIED, ARISING BY LAW OR OTHERWISE, WITH RESPECT TO THE PRODUCT, ACCOMPANYING DOCUMENTATION OR SOFTWARE AND ANY OTHER GOODS OR SERVICES DELIVERED UNDER THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO ANY: (A) IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE; (B) IMPLIED WARRANTY ARISING FROM COURSE OF PERFORMANCE, COURSE OF DEALING, OR USAGE OF TRADE; (C) CLAIM OF INFRINGEMENT OR MISAPPROPRIATION; OR (D) CLAIM IN TORT (WHETHER BASED ON NEGLIGENCE, STRICT LIABILITY, PRODUCT LIABILITY OR OTHER THEORY). SYNOLOGY MAKES NO GUARANTEE AND SPECIFICALLY DISCLAIMS ANY WARRANTY THAT THE DATA OR INFORMATION STORED ON ANY SYNOLOGY PRODUCT WILL BE SECURE AND WITHOUT RISK OF DATA LOSS. SYNOLOGY RECOMMENDS THAT CUSTOMER TAKES APPROPRIATE MEASURES TO BACK UP THE DATA STORED ON THE PRODUCT. SOME STATES/JURISDICTIONS DO NOT ALLOW LIMITATIONS ON IMPLIED WARRANTIES, SO THE ABOVE LIMITATION MAY NOT APPLY TO CUSTOMER.
3.7 Extended Warranty Plus Limitations. (a) The Customer must complete the purchase of the Extended Warranty Plus Service within ninety (90) days following the original purchase date of the new Product. (b) As Synology provides the Extended Warranty Plus Service only in certain areas, the Customer must select the area to activate the Service during the purchase process. If the Customer requests Extended Warranty Plus Service from an area other than the selected area, Synology, at its sole discretion, may not provide Extended Warranty Plus Service; (c) Exceptions to coverage: The Extended Warranty Plus Service does not apply to overseas departments, overseas territories, overseas autonomous regions, and islands other than the main island of the countries and regions.
Section 4. Limitations of Liability
4.1 Force Majeure. Synology will not be liable for, or be considered to be in breach of or default under this Warranty on account of, any delay or failure to perform as required by this Warranty as a result of any cause or condition beyond its reasonable control (including, without limitation, any act or failure to act by Customer).
4.2 Disclaimer of Certain Damages. IN NO EVENT WILL SYNOLOGY OR ITS SUPPLIERS BE LIABLE FOR THE COST OF COVER OR FOR ANY INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL OR SIMILAR DAMAGES OR LIABILITIES WHATSOEVER (INCLUDING, BUT NOT LIMITED TO LOSS OF DATA, INFORMATION, REVENUE, PROFIT OR BUSINESS) ARISING OUT OF OR RELATING TO THE USE OR INABILITY TO USE THE PRODUCT, ANY ACCOMPANYING DOCUMENTATION OR SOFTWARE AND ANY OTHER GOODS OR SERVICES PROVIDED UNDER THIS WARRANTY, WHETHER BASED ON CONTRACT, TORT (INCLUDING NEGLIGENCE), STRICT LIABILITY OR OTHER THEORY EVEN IF SYNOLOGY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
4.3 Limitation of Liability. SYNOLOGY’S AND ITS SUPPLIERS’ LIABILITY ARISING OUT OF OR RELATING TO THE USE OR INABILITY TO USE THE PRODUCT, ANY ACCOMPANYING DOCUMENTATION OR SOFTWARE AND ANY OTHER GOODS OR SERVICES PROVIDED UNDER THIS WARRANTY IS LIMITED TO THE AMOUNT ACTUALLY PAID BY CUSTOMER FOR THE PRODUCT REGARDLESS OF THE AMOUNT OF DAMAGES CUSTOMER MAY INCUR AND WHETHER BASED ON CONTRACT, TORT (INCLUDING NEGLIGENCE), STRICT LIABILITY OR OTHER THEORY. The foregoing disclaimer of certain damages and limitation of liability will apply to the maximum extent permitted by applicable law. The laws of some states/jurisdictions do not allow exclusion or limitation of certain damages. To the extent that those laws apply to the Product, the exclusions and limitations set forth above may not apply to Customer.
Section 5. Miscellaneous
5.1 Proprietary Rights. The Product and any accompanying Software and documentation provided with the Product include

proprietary and intellectual property rights of Synology and its third party suppliers and licensors. Synology retains and reserves all right, title, and interest in the intellectual property rights of the Product, and no title to or ownership of any intellectual property rights in or to the Product, any accompanying Software or documentation and any other goods provided under this Warranty is transferred to Customer under this Warranty. Customer will (a) comply with the terms and conditions of the Synology end user license agreement accompanying any Software furnished by Synology or an authorized Synology distributor or reseller; and (b) not attempt to reverse engineer any Product or component thereof or accompanying Software or otherwise misappropriate, circumvent or violate any of Synology’s intellectual property rights.
5.2 Assignment. Customer will not assign any of its rights under this Warranty directly, by operation of law or otherwise, without the prior written consent of Synology.
5.3 No Additional Terms. Except as expressly permitted by this Warranty, neither party will be bound by, and each party specifically objects to, any term, condition or other provision that conflicts with the provisions of this Warranty that is made by the other party in any purchase order, receipt, acceptance, confirmation, correspondence or otherwise, unless each party specifically agrees to such provision in writing. Further, if this Warranty conflicts with any terms or conditions of any other agreement entered into by the parties with respect to the Product, this Warranty will prevail unless the other agreement specifically references the sections of this Warranty that it supersedes.
5.4 Applicable Law. Unless explicitly prohibited by local law, this Warranty is governed by the laws of the State of Washington, U.S.A. for the Customers residing within the United States; and by the laws of the Republic of China (Taiwan) for Customers not residing within the United States, without regard to any conflict of law principles to the contrary. The 1980 U.N. Convention on Contracts for the International Sale of Goods or any successor thereto does not apply.
5.5 Dispute Resolution. Any dispute, controversy or claim arising out of or relating to this Warranty, the Product or services provided by Synology with respect to the Product or the relationship between Customers residing within the United States and Synology will be resolved exclusively and finally by arbitration under the current commercial rules of the American Arbitration Association, except as otherwise provided below. The arbitration will be conducted before a single arbitrator, and will be limited solely to the dispute between Customer and Synology. The arbitration, or any portion of it, will not be consolidated with any other arbitration and will not be conducted on a class-wide or class action basis. The arbitration shall be held in King County, Washington, U.S.A. by submission of documents, by telephone, online or in person as determined by the arbitrator at the request of the parties. The prevailing party in any arbitration or legal action occurring within the United States or otherwise shall receive all costs and reasonable attorneys’ fees, including any arbitration fee paid by the prevailing party. Any decision rendered in such arbitration proceedings will be final and binding on the parties, and judgment may be entered thereon in any court of competent jurisdiction. Customer understands that, in the absence of this provision, Customer would have had a right to litigate any such dispute, controversy or claim in a court, including the right to litigate claims on a class-wide or class-action basis, and Customer expressly and knowingly waives those rights and agrees to resolve any disputes through binding arbitration in accordance with the provisions of this Section 5.5. For Customers not residing within the United States, any dispute, controversy or claim described in this section shall be finally resolved by arbitration conducted by three neutral arbitrators in accordance with the procedures of the R.O.C. Arbitration Law and related enforcement rules. The arbitration shall take place in Taipei, Taiwan, R.O.C., and the arbitration proceedings shall be conducted in English or, if both parties so agree, in Mandarin Chinese. The arbitration award shall be final and binding on the parties and may be enforced in any court having jurisdiction. Nothing in this Section shall be deemed to prohibit or restrict Synology from seeking injunctive relief or seeking such other rights and remedies as it may have at law or equity for any actual or threatened breach of any provision of this Warranty relating to Synology’s intellectual property rights.
5.6 Attorneys’ Fees. In any arbitration, mediation, or other legal action or proceeding to enforce rights or remedies under this Warranty, the prevailing party will be entitled to recover, in addition to any other relief to which it may be entitled, costs and reasonable attorneys’ fees.
5.7 Export Restrictions. You acknowledge that the Product may be subject to U.S. export restrictions. You will comply with all applicable laws and regulations that apply to the Product, including without limitation the U.S. Export Administration Regulations.
5.8 Severability. If any provision of this Warranty is held by a court of competent jurisdiction to be invalid, illegal, or unenforceable, the remainder of this Warranty will remain in full force and effect.
5.9 Entire Agreement. This Warranty constitutes the entire agreement, and supersedes any and all prior agreements, between Synology and Customer related to the subject matter hereof. No amendment, modification or waiver of any of the provisions of this Warranty will be valid unless set forth in a written instrument signed by the party to be bound thereby.
5.10 Extended Warranty Plus Service Payment and Termination. (a) Upon verifying the purchase order by Synology, the Customer shall immediately pay all charges and tax. Synology reserves the right to refuse to provide the Extended Warranty Plus Service to Customer who are ineligible or who are under statutory age. (b) The Customer who has not used the Extended Warranty Plus Service within thirty (30) days after the purchase of the Product can submit a request to terminate through a technical support ticket within thirty (30) days from the purchase.
Powered by TCPDF (www.tcpdf.org)

FCC Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

B

VCCI B

Declaration Letter of REACH & RoHS Compliance
About REACH In June 2007, the European Union Regulation (EC) 1907/2006 concerning the Registration, Evaluation, Authorization and Restriction of Chemicals (REACH) was first released. Under this Regulation, manufacturers are required to gather information on the properties of their chemical substances, which will allow their safe handling, and to register the information to European Chemicals Agency (ECHA). The aim is to improve the protection of human health and the environment through the better and earlier identification of the intrinsic properties of chemical substances.
About RoHS RoHS Directive (EU Directive 2002/95/EC ) was issued in 2002, restricted the use of the six chemicals lead, cadmium, mercury, and hexavalent chromium, as well as flame retardants polybrominated biphenyls (PBBs) and polybrominated dipheny ethers (PBDEs). Under this directive, manufacturers are required to replace these chemicals in their products with less hazardous alternatives.
Then RoHS 2.0 (Directive 2011/65/EU) has replaced Directive 2002/95/EC since January 3, 2013. In 2015, EU commission publishes Directive (EU) 2015/863 to amend Annex II to EU RoHS 2 (Directive 2011/65/EU) to add 4 phthalates (DEHP, BBP, DBP and DIBP) onto the list of restricted substances from 22 July 2019.
REACH and RoHS Compliance Synology meets all requirements of the REACH Regulation and is compliant to all implemented RoHS type regulations worldwide. To the best of Synology’s knowledge, all Synology products in production (including finished

products, spare parts, and packaging materials) are in compliance with the requirements of the Regulation and/or Directives. Synology continues to monitor, influence, and develop our processes to comply with any proposed changes to the Regulation and/or Directives.

References

• The GNU General Public License v3.0 - GNU Project - Free Software Foundation
• TCPDF
• Synology Community
• Knowledge Center
• How do I make a warranty claim for my Synology product? - Synology Knowledge Center
• How do I reset my Synology NAS? (For DSM 6.2.4 or above) - Synology Knowledge Center
• What is SSD Estimated Endurance, and how does it affect the warranty of my Synology SSD? - Synology Knowledge Center
• Synology Knowledge Center
• Synology Knowledge Center
• Navigate Desktop | Surveillance Station - Synology Knowledge Center
• Knowledge Center

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>