MULANNIC HM6 Indoor Outdoor Thermometer Hygrometer Instruction Manual

HM6
Wireless Indoor/Outdoor
Humidity & Temperature Monitor
INSTRUCTION MANUAL

HM6 Indoor Outdoor Thermometer Hygrometer

Email: mulannic@outlook.com
Please read the user manual carefully and keep for future reference.

Specifications

1. Product Model: HM6
2. Product Size: 767315mm
3. Temperature Display unit: °C/°F
4. Temp Range: -50°C~70°C (-58°F~158°F)
5. Temp Accuracy: +1°C (+1.8°F)
6. Humidity Range: 1% ~ 99%
7. Humidity Accuracy: 40%=70%: 3%; <30% or >70%: +5%
8. Comfort Display:
9. Charging: 5V2A, TYPE C interface
10. Receiver Battery Capacity: 300mAh
11. Transmitter Power Supply: 2*AAA batteries (included)
12. Charging Time & Runtime: Each full charge (60 minutes) can be used for 4-6 months
13. Refresh Rate: 2.5 seconds
14. Placement: Tabletop Stand / Magnetic Back / Hanging Hole
15. Waterproof Transmitter: Can be drenched with rain, splashed with water, and prevented from dust
16. Connection Distance Range: Measured 60-90 meters

Receiver Function Description:

Please turn on the receiver switch first. When the screen enters the search pairing status, turn on the transmitter and load the battery, it will automatically search for the connection without your operation.
Press the On/off key to turn on the device and enter the search state Open the battery cover of transmitter and load the batteryAutomatically search for signals to connect ON/OFF °C/°F:

1. Short press once to turn on/off the receiver;
2. Long press for 2s to switch °C/°F.

ALL TIME/24 HRS:

Short press: (24HRS(MAX)—24HRS(MIN)—ALL TIME-(MAX)—ALL TIME-(MIN)) . Press and hold for 2s: Clear the maximum and minimum values / repair

1. Short press to display the temperature and humidity of 24HRS MAX, 24HRS MIN, ALL TIME MAX and ALL TIME MIN in sequence, each display time is 10s, if there is no operation for 10s, the temperature and humidity values in the current state will be restored.
2. If it’s on the page of ALL TIME / 24 HRS — long press for 2s to clear the maximum and minimum value.

Backlight (touch):
Short touch once to turn on the backlight (the backlight lasts for 10s, and automatically turns off after 10s).
RESET:
When the product is crashed/ abnormal displayed/inoperable, you can use a sharp object such as a card needle to stick into the “RESET” hole to restore the product to factory settings.
Temperature and humidity change prompt:
When the current humidity or temperature tends to be stable, the icon appears.
When the current temperature or humidity continues to rise, the icon appears.
When the current temperature or humidity continues to fall, the icon appears.
Emoji display:
When the humidity is below 40%, the icon appears.
When the humidity is between 40% and 70%, the icon appears.
When the humidity is higher than 70%, the icon appears.
Low battery indication:
The battery icon is fully displayed when the battery is fully charged.
When the battery voltage is lower than 3.3V, the battery icon becomes a flashing empty frame to prompt consumers to charge. When the battery voltage is lower than 3V, it automatically shuts down.
Charging:
TYPE C interface, the battery icon rolls during charging. When fully charged, the battery icon no longer rolls and the full frame is displayed.
Signal icon:

1. After the device turns on, the signal icon flashes for three minutes, meaning that the device is pairing.
2. Within three minutes, if there is a successful pairing of devices, the signal icon will stop flashing.
3. If no device is successfully paired within three minutes, the signal icon will disappear. If you want to try pairing again, please long press the MAX/MIN key for 2s(not in the 24HRS or ALL TIME page) to enter the paring state.

Transmitter Function Description:

Signal Indicator:
It flashes once after the device is powered on (about 1s).
When the XT button is pressed briefly to transmit the signal, it flashes once (about 1s);
When the reset is completed, it flashes once (about 1s);
When the signal is automatically transmitted every 30s, it flashes once (about 1s).
XT button:
The signal transmitting key. When the receiver is pairing, short press within 5s to pair with the receiver, and the signal indicator will flash for about 1s.(When the receiver is pairing, the power on the transmitter can automatically pair with the receiver.)
RESET:
The reset key. When the product is crashed, does not send any signal, cannot be operated, etc., short press the key once to reset. When the reset is completed, the signal indicator flashes once for about 1s. (Please do not use reset in non-emergency situations. If you have to use it, please repair it. Switch on the receiver, when the screen enters the search pairing state, open the transmitter and load the battery, it will automatically search for the connection without your operation.)
Low battery prompt:
When the battery is fully charged, the battery icon is displayed in a full frame. When the battery level is lower than 2.7V, the battery icon becomes an empty frame flashing to prompt consumers to change the battery; when the battery level is lower than 2.4V, it automatically shuts down.

Cautions:

1. Please turn on the receiver switch first. When the screen enters the search pairing state, turn on the transmitter and load the battery, it will automatically search for the connection without your operation.
2. When using this product for the first time, it is recommended that the product be fully charged before use.
3. When the icon appears during use, please use the supplied adapter and data cable to charge the product in time. It takes about 60 minutes to fully charge the battery of this product after it is completely discharged.
4. Daily maintenance: use a soft tissue or cloth to clean the product, and keep the product clean and dry.
5. The transmitter is surrounded by a waterproof process, so it can be drenched in rain, splashed with water, and prevented from dust. But the bottom is a vent, so you need to hang it, don’t place it upside down or flat, to prevent rain from seeping in through the vent to destroy the transmitter.

FAQ:

Q1: The outdoor transmitter sensor does not work.

A1: Please repeat the operation: Turn on the receiver switch first. When the screen enters the search pairing state, turn on the transmitter and load the battery, it will automatically search for the connection.

Q2: The display screen does not work.

A2: Please charge the receiver, or replace two AAA batteries for the transmitter.

Q3: Inaccurate display of temperature/humidity, indoor and outdoor.

A3: When the display of temperature and humidity is not accurate, the product has entered the state of pairing and searching for a signal, however, due to the geographical location of each user, the weather environment changes in a variety of ways, and the feedback of data does not reach a stable value. It takes about 15-30 minutes to stabilize the signal transmission depending on different scenarios.

MADE IN CHINA
CAN ICES-3(B) / NMB-3(B)
MADE IN CHINA
Model:HM6
Manufacturer:Dongguan Baiqi Electronic Technology Co.,Ltd.
Jinyi Industrial Park,No.3 Yinsong Road,Qingxi Town,Dongguan City,
Guangdong Province

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>