ZETTI Coast Airship Coast Bundle User Guide

Coast Airship Coast Bundle
User Guide

Coast Airship Coast Bundle

USER GUIDE: Coast

Welcome to the Zetti Team!
We want to ensure you get the most of our incredible products so please read the directions carefully. If you have any specific concerns or questions please reach out to our customer support.

• Website: www.zettibrand.com
• Email: hello@zettibrand.com
• Facebook: www.facebook.com/thezettibrand/
•  Instagram: @zettibrand

Also be sure to share your awesome experiences with our products! Tag us on your favorite social platforms or simply email us directly with any of your favorite images, videos, and stories.

INCLUDED COMPONENTS

(Full Hydrofoil)

• Carrying Bag
• Mast
• Fuselage
• Front wing(s)
• Rear wing
• Stainless Steel T-nut
• Torx L-Key driver

INSTRUCTIONS

Assemble Hydrofoil

1. Remove foil components from bag

2. Remove torx keys and mounting hardware Reference table below for correct combinations
   Front wing| 3x| M8x25mm
   ---|---|---
   Rear wing| 2x| M6x25mm
   Mast| 4x| M8x35mm
   T-Nut| 4x| M8x22mm

3. Assemble front and rear wing to fuselage
   ● Add foil covers to protect carbon wings from accidental damage

4. Add Top plate to Mast

5. Add mast assembly to fuselage assembly

6. Mount to board
   ● See instructions for pairing with Airship inflatables
   ● Don’t forget to remove covers before use!

Attach Hydrofoil (Zetta Coast) to Board (Airship)

1. Assemble Hydrofoil mast, base, fuselage and wings according to manufacturer spec

2. Turn inflated board over on clean flat surface

3. Add included M8x22mm screws into each t-nut and rotate 1 full turn

4. Insert T-nut assembly into US Box (2 each) and move to all 4 corners of track

5. Place hydrofoil on top of the carbon plate
   ● Make sure to stabilize the mast with one hand to keep foil upright during this process.

6. Move screws through the slots and into the countersunk recession on the mast base

7. Move to desired location and tighten screws

8. Check tightness of all screws
   ● Go ride!
   ● Adjust mast location as necessary for your weight, riding style, and foil

ASSEMBLY NOTES:

Zetti Airship uses industry standard 9cm track, and is compatible with most brands on the market.
Please ensure the mast plate screw lengths and T-nut threads are the correct size. Failure to do so can cause damage to the board upon installation.

• Some hydrofoils do not have slots and must be attached by these following steps – beginning after step 3 on the previous page:

  1. Carefully place the mast base over the T-nuts
  2. Insert M8 screw through the hole on the mast base and then screw into the t-nut
  3. Repeat for all 4 screws
  4. Move foil base into desired location
  5. Tighten screws

RECOMMENDATIONS

HYDROFOIL CARE:

• To ensure longevity of components it is recommended to use anti-seize thread grease on the screws during assembly

• During each session occasionally check to ensure screws have remained tight

• After each session disassemble the hydrofoil for storage in included carrying case
  ○ Remove Stainless screws from the aluminum mast and fuselage

• Failure to do so may cause the screws to corrode and seize

• This is especially important in salt water environments

• Note: using titanium screws considerably eliminates any possible corrosion

• These can be purchased separately
  ○ Rinse all parts in fresh water and allow to dry before long term storage

SAFETY AND RELEASE OF LIABILITY

Zetti hydrofoil boards, hydrofoils, wings and other products are used in sports that are considered inherently dangerous. Any use of Zetti Brand products releases Zetti Brand, LLC from liability from damage or injury caused by improper  use, pre-existing damage, extreme wear and tear, or adverse weather conditions. Please follow directions and safety recommendations carefully! Inflate board to recommended pressure of 15-20psi and be sure to check that the valve is in  proper working order. Make sure the valve is closed properly before use.
Do not go further from shore than you are willing to swim back. If the board deflates there is no extra flotation compartment.
Use included board leash at all times. It is very easy to become separated from your board without a leash. Under extreme circumstances it may be necessary to disconnect from your board to prevent injury, for example, in large breaking  swell. Please do so carefully, and have a plan to return to shore before release.
It is recommended to always wear a wetsuit and Personal Flotation Device (PFD) or lifejacket while using our products. Please follow local laws and practice in safe locations away from marine traffic.
Minors must have adult supervision at all times while using the product.

WARRANTY

Please review the package upon receipt and inspect for damage or manufacturing defects prior to first use.
If defects are found please reach out to Zetti support immediately and we will work out a warranty replacement. This warranty replacement does not apply if the product was purchased with prior knowledge of defect or is due to materials added or mishandling of product.
We will happily accept returns within 30 days from the date of delivery if the product is in an unused and undamaged condition.
All of our products are guaranteed for 90 days from the date of delivery from manufacturing defects.

Limitations of Warranty

We manufacture our products with the highest quality of components and control. While we take care to make sure the highest quality product is shipped to our customers we cannot cover all damage incurred to the Product, and we must exclude:

• Normal wear and tear
• Damage caused by overpressure
• Impacts, scratches, or damage caused by foreign objects
• Damage caused by collisions
• Overexposure to UV, sun, salt, or humidity
• Improper storage
• Damage caused by waves, shore break, or extreme weather
• Damage caused by non-approved repair; professional or otherwise
• Damage caused by unintended use of the Product; ie: rafting or towing behind boat
• Damage caused by improper mounting outside of recommendations
• Damage or personal injury to the user while using the Product
• Damage or personal injury caused by the user to others when using the Product

Warranty is only valid if product is used for its intended purpose; WinG foil, Surveil, Sup foil, Wake foil, or Kite foil in leisure and does not cover products used for hire or in competition.
Note:
During a crash the board may flip upside down exposing the hydrofoil. As the board rolls back, the hydrofoil may contact the user or puncture the wing canopy or bladder. Do your best to prevent high speed or extreme crashes that can  result in these conditions. This is a common occurrence during foiling and is not covered by warranty.

References

• ZETTI Airship Wingfoil Boards and Hydrofoils – Zetti Brand

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>