PENAOVER S0511 Power Bank Instruction Manual
- June 16, 2024
- PENAOVER
Table of Contents
PENAOVER
S0511
POWER BANK
Instruction Manual
Component description
- Mobile phone magnetic wireless chargin
- Watch magnetic wireless charging
- Fast charge lamp
- Wireless charging fast charging lamp
- Battery Indicator light
- Magnetic stand
- Lanyard thread hole
- Power on/off
Input charging
Type-C/Lightning Input charge
Use the built-in Type-C charging cable or Lightning charging cable to connect
to the input interface, and then start charging the mobile power supply.
During the charging process, the corresponding power indicator flashes to
charge the device. Four power indicators are steady on, charging is complete.
Power bank discharge
Take out the mobile phone,ipad, Bluetooth headset and other electronic
devices, and charge with the mobile power supply, the corresponding power
indicator is steady on, which is normal discharge; The first power flash
discharge (under voltage) indicates that the mobile power is about to run out
of power Power button description
Click the power button to display the current power, and double click
thebutton to turn off the power indication
Mobile phone wireless charging instructions
f the mobile phone supports wireless charging function, the mobile phone can
be charged directly on the mobile phone wireless charging position (start
voltage: 5.0± 0.25V, wireless output power: 5W/7.5W/10W/15W Max)
Watch wireless charge description
If the watch supports wireless charging function, the watch can be charged
directly on the wireless charging position of the mobile power supply watch
(startup voltage: 5.0±0.25V, wireless output power: 2.5W)
Battery light
The mobile power supply is equipped with a power display LED, which is convenienfor you to control the remaining power of the mobile power supply and other functions. If the four lights are steady on, the power supply is sufficient. If the fist light blinks or the power display light is not bright, the mobile power supply needs to be charged.
The battery level is displayed as four white lights.the fast charging lamp is green, the wireless charging lamp is blue, the wireless fast charging lamp is blue, and the green is on. Watch wireless charge white light steady on.
Specification parameters
Brand | PENAOVER |
---|---|
Name | Power Bank |
Model number | S0511 |
Cell | Polymer cell |
Battery capacity | 5000mAh(19.25Wh/3.85V) |
Maximum ouput power | PD2OW |
Type-C Input | 5V 3A,9V 2.2A (±0.1) |
Type-C Output | 5V 3A,9V 2.2A,12V 1.66A |
Lightning Input | 5V 3A |
Input interface | Type-C / Lightning |
Output interface | Type-C |
Wireless Charging Power | 5W/7.5W/10W/15W |
Watch Wireless Charging Power | 2.5W |
Material | ABS+PC |
Product size | 103.8*67.51 5.5mm |
Weight | 141g |
Execution standard | GB/T 35590-2017 |
Power protection
Short circuit protection
If the power output is short circuited, the power supply shall be able
toprotect automatically and the power supply shall be able to resume0operation
after troubleshooting
Overvoltage protection
The mobile power supply has overcharge and discharge protection The product
output is provided with overvoltage protection, and the outputvoltage shall
not exceed 5 6The input voltage range is 4 6.56\V.and the input has OVP
andundervoltage protection functions
Overcharge protection
Use DC 5V/2A constant current and constant voltage source to connect the
mobilepower input terminal, charge to 100% power After (saturation state),
continue to loathe mobile power supply for 8 hours, and the mobile power
supp/y should not explode,fire, smoke of leak
Over discharge protection
The output terminal of mobile power supply shall be connected to 30 Q load fo
r 24hours and the mobile power supp/y shall not explode, fire or smoke Or
leakage
Aftertroubleshooting, the power supply shall be able to resume operation
Common problems and precautions
Common problem | Possible causes |
---|
what if the power supply
can’t be charged?| 1 Confirm whetherthe indicator screen is on
2 Confirm whether the data cable and piug arenot in contact OK replace it
again and try again
3 Confirm the remaining power and use up theremaining power Recharging
The power bank supply is
not fully charged| It is necessary to activate the cell for thefrst use and
use it for 2-3 imes See f itcan be filed
Matters needing attention
iPhone Charging Instructions
The iPhone may heat up a bit while charging. To extend battery life, if the
battery overheats, the software may limit charging when it reaches 80%. When
the temperature drops, the iPhone charges again. Try moving your iPhone and
power bank to a cooler location.
Warn
Failure to follow safety instructions may result in fire, electric shock, ring
damage or other njuries.high-quality power banks are used Lithium polymer
battery, please use it with confidence
Do not disassemble or pierce the power bank by yourself; do not expose the
power bank to firehigh temperature or water,It is recommended to use a regular
brand power adapter to charge it
If you find that the mobile power supply is bulging or other bad phenomena or
the charged deviceis bulging. please stop using the power supply, fhis product
is only suitable for safe use in areas with an altitude of 2000m and below,and
only suitable for safe use in non-tropical climate conditions
CAUTION Replacing a battery with the wrong type can result in an
explosion hazard be sure to dispose of the used battery according to the
instructions
Suggestions for scrapping power supply:
The power supply contains dangerous and useless materials, which need to be
recycled(destroyed) by qualified institutions, Contact your local office to
ensure that the power supply is properly scrapped in accordancewith the
approved regulations
Packing list:
- Power Bank x1
- Manual X1
- BlisteringX1
- Type-C to Type-C
- Charging Cable x1
- Lanyard box x1
- SIM card ejector x1
- Type-C to Lightning
- Charging Cable x1
DIV decorative lanyard charging cable:
-
Remove the cable from the female end and thread the cable through the lanyard hole
-
After threading the lanyard hole of the device, pick out the cable end with the included card needle. And put into nut head.
-
Take out the male end of the lashing cable, align it with the female end of the nut, and tighten it counterclockwise.
-
If you need to remove the decorative lanyard cable, unscrew the female screw cap and take out the decorative cable.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1)This device may not cause harmful
interference. (2)This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note:This equipment has been tested and found to comply with the limits for a
class B digital device,pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequence energy and,if
not installed and used in accordance with the instructions,may cause harmful
interference to radio communications.However,there is no guarantee that
interference will not occur in a particular installation.if this equipmemt
does cause harmful interference to radio or television reception,which can be
determined by turning the equipment off and on,the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an autlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.