PENAOVER TW1012 All In One Power Bank Instruction Manual
- June 14, 2024
- PENAOVER
Table of Contents
TW1012 All-in-one power bank
Instruction Manual
Component description
- Mobile power on button
- Type-C in/output interface
- USB-A (1) output interface
- Power indicator
- Pin
- Wireless charging (this function needs to be supported by the mobile phone)
- floodlight
- Built in cable type-C output interface
- Cable for iphone
Charging instructions
Pin input charging
Connect the device with the charging interface suitable for the device and
start charging the mobile power supply. During the charging process The last
character of the digital screen flashes to charge the equipment; All
characters on the digital screen are always on, and the charging is completed.
USB / type-C input charging
USB / type-C input charging uses the built-in USB charging cable or type-C
charging cable to access the input interface. At this time, it starts to
charge the mobile phone Source charging: during charging, the last character
of the digital screen flashes to charge the equipment; All words of digital
screen Fu Changliang, charging completed.
Mobile power discharge
When using mobile power to charge other electronic devices such as mobile
phones, iPads, Bluetooth headsets, etc, The digital screen is always on to
display the corresponding power, which belongs to normal discharge; The last
character of the digital screen flashes (low power) During 5%) discharge
(under voltage), it indicates that the mobile power supply is about to run out
of power.
Power button description
Click the power button to display the current power, and double-click the
button to turn off the power indication.
Wireless charging instructions
If the mobile phone supports the wireless charging function, the mobile phone
can be directly placed at the wireless charging position of the charging
treasure Charging (startup voltage: 5.0 ± 0.25V, wireless output power: 5W /
7.5w/1 w/15w max)
Power indicator
The mobile power supply is equipped with a digital screen to facilitate your control of the remaining power and other functions of the mobile power supply,100% of the power indicates that the mobile power supply is sufficient. If 0% is displayed, the mobile power supply needs to be charged.
Specification Parameters
Model: | TVV1012 ( PENAOVER ) |
---|---|
Name: | All-in-one power bank |
Cell: | Polymer cell |
Battery capacity: | 10000mAh (37Wh/3.7V) |
Wireless Charging Power: | 5W/7.5W/10W/15W |
USB Output: | 5V 3A, 9V 2.2A, 12V 1.67A, 5V 4.5A, 4.5V **** |
5A
Type-C Cable Output:| 5V 3A, 9V 2.2A, 12V 1.67A, 5V 4.5A,
4.5V 5A
Lightning Cable Output:| 5V 3A
Type-C Input/ Output:| 5V 3A, 9V 2.2A, 12V 1.67A
Type-C+USB+Cable Output:| 5V 3A
Input interface:| Type-C/ Pin
Output interface:| Lightning/Type-C comes with cable, USB-A
Material:| ABS+PC
Product size:| 84.884.825.8MM
Weight:| 255g
Execution standard:| GB/T 35590-2017
Power protection
Short circuit protection
If the power output is short circuited, the power supply shall be able to
protect automatically, and the power supply shall be able to resume operation
after troubleshooting.
Overvoltage protection
The mobile power supply has overcharge and discharge protection.
The product output is provided with overvoltage protection, and the output
voltage shall not exceed 5.6V
The input voltage range is 4.6V-5.6V, and the input has OVP and undervoltage
protection functions.
Overcharge protection
Use DC 5V/2A constant current and constant voltage source to connect the
mobile power input terminal, charge to 100% power After (saturation state),
continue to load the mobile power supply for 8 hours, and the mobile power
supply should not explode, fire, smoke or leak.
Over discharge protection
The output terminal of mobile power supply shall be connected to 30 Q load
for 24 hours, and the mobile power supply shall not explode, fire or smoke Or
leakage. After troubleshooting, the power supply shall be able to resume
operation.
Common Problems and precautions
| common problem| Possible causes
---|---|---
1| What if the power supply can’t be charged?| 1. Confirm whether the
indicator screen is on
2. Confirm whether the data cable and plugare not in contact OK, replace it
again and try again
3. Confirm the remaining power and use up the remaining power Recharging
2| When the power supply is charged to 99%Stopped charging| It is necessary to
activate the cell for the first use, and use it for 2-3 times See if it can be
filled
3| After receiving the goods, the remaining power is only displayed 70% of|
The Coulomb of digital display needs to be recycled 2-3 The true power of the
power supply will be displayed accurately after
times Please recycle it for 2-3 times before estimating
Matters needing attention
Warn
Failure to follow safety instructions may result in fire, electric shock, ring
damage or other injuries; high-quality power banks are used Lithium polymer
battery, please use it with confidence.
Do not disassemble or pierce the power bank by yourself; do not expose the
power bank to fire, high temperature or water;It is recommended to use a
regular brand power adapter to charge it.
If you find that the mobile power supply is bulging or other bad phenomena or
the charged device is bulging, please stop using the power supply;
This product is only suitable for safe use in areas with an altitude of 2000m
and below, and is only suitable for safe use in non-tropical climate
conditions.
CAUTION: Replacing a battery with the wrong type can result in an
explosion hazard, be sure to dispose of the used battery according to the
instructions.
Suggestions for scrapping power supply:
The power supply contains dangerous and useless materials, which need to be
recycled (destroyed) by qualified institutions,
Contact your local office to ensure that the power supply is properly scrapped
in accordance with the approved regulations.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that maycause undesired operation.
Changes or modifications not expressly approved by the party responsible
forcompliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a class Bdigital device,pursuant to Part 15 of the FCC Rules. These limits
are designed to providereasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequence energy and,if
not installed and used in accordance with the instructions,may cause harmful
interference to radio communications.However,there is no guarantee that
interference will not occur in a particular installation.if this equipmemt
does cause harmful interference to radio or television reception,which can be
determined by turning the equipment off and on,the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an autlet on a circuit different from that to which thereceiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The devicecan be used in portable exposure condition without restriction.