iRobot Roomba j9+ Self-Emptying Robot Vacuum User Guide

Getting Started

Roomba j9+ Self-Emptying Robot Vacuum

Get ready
To start, you’ll need your robot, charging station, and power cord. Set other accessories aside for later. Position the charging station
Place charging station near an outlet in an area with good Wi-Fi coverage. Keep the area around the charging station free of clutter. Plug in the charging station
Plug the power cord into the charging station, then into the wall. Wrap the cord back so it won’t get in the way of the robot as it comes and goes.

Read enclosed safety information guide first before using your robot. Wake up Roomba®
Place your robot on the charging station by lining up the metal charging contacts. After a few minutes, a sound will let you know it’s awake.

https://link.irobot.com/YArx

Download the iRobot Home App
Scan the code with the camera on your mobile device (or find the iRobot Home App in your app store).
Complete setup in the app to allow your robot to identify and avoid obstacles in real time.  Find more ways to connect
If you need further assistance, visit homesupport.irobot.com/s/j9plusownersguide

Safety Information

Important Safety Information

This owner’s guide includes information for Regulatory Model(s): RVE-Y2, ADG-N1, Battery Model(s): ABL-F, ABL-D2Ax, ABL-D2Bx (x = 1 or 2)

SAVE THESE INSTRUCTIONS
WARNING: When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS
WARNING: To reduce the risk of injury or damage, read and follow the safety precautions when setting up, using, and maintaining your robot.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

| This is the safety alert symbol. It is used to alert you to potential physical injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
---|---
| Risk of electric shock
| Risk of fire
| Caution
| Class II equipment
| For indoor use only
| Class III equipment
| Rated power output, d.c.
| Rated power input, d.c.
| Rated power input, a.c.
| Read operator’s manual
| Keep out of reach of children
| General symbol for recycling
| Separate Supply Unit

WARNING: Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
NOTICE: Indicates a hazardous situation that, if not avoided, could result in property damage.

GENERAL

WARNING

• This product comes with a region approved power supply cord and is designed to be plugged into a standard household AC power outlet only. Do not use any other power supply cord or power strip. For replacement cords, please contact Customer Care to ensure proper selection of country specific power supply cord.

• Do not disassemble or open the dirt disposal unless instructed to do so.
  There are no user serviceable parts inside. Refer servicing to qualified service personnel.

• Risk of electric shock, use indoors in dry location only.

• Do not handle this product with wet hands.

• Do not use unauthorized chargers. Use of an unauthorized charger could cause the battery to generate heat, smoke, catch fire, or explode.

• This product is not a toy. Small children and pets should be supervised when the product is operating.

• Do not sit or stand on this product.

• Store and operate this product in room temperature environments only.

• If the room to be cleaned contains a balcony, a physical barrier should be used to prevent robot access to the balcony and ensure safe operation.

• Clean cliff sensors for buildup.

• If the room to be cleaned contains equipment, such as a stove, fan, space heater, or humidifier, remove the equipment before operation.
  There is a risk of injury, accident or malfunction if the robot comes in contact and pushes the equipment.

• This robot is intended for dry floor use only. Do not use this device to pick up spills. Do not allow your robot or charging station to become wet.

CAUTION

• Do not operate the robot in areas with exposed electrical outlets in the floor.
• Do not use this device to pick up sharp objects, glass, or anything that is burning or smoking.
• Be aware that the robot moves on its own. Take care when walking in the area that the robot is operating in to avoid stepping on it or tripping over it.
• If the device passes over a power cord and drags it, there is a chance an object could be pulled off a table or shelf. Before using this device, pick up objects like clothing, loose papers, pull cords for blinds or curtains, power cords, and any fragile objects.  Extinguish candles. Shut off space heaters.
• Perform the required maintenance per the Owner’s Guide to ensure safe operation of the robot and charging station.

NOTICE

• Do not place anything on top of your robot or charging station.
• The failure to maintain cleanliness of charger contacts could result in loss of ability for the robot to charge the battery.
• Before running your robot on carpets or rugs, ensure that the carpets or rugs are compatible with vacuums using bars or brushes. Using your robot on a carpet or rug that is not compatible could result in damage to your carpet or rug. Contact your carpet or rug manufacturer with questions on compatibility.

BATTERY

WARNING

• Do not open, crush, heat above 176°F: 80°C, or incinerate. Follow the Owner’s Guide instructions for proper use, maintenance, handling, and disposal.
• Do not short-circuit the battery by allowing metal objects to contact battery terminals or immerse in liquid. Do not subject batteries to mechanical shock.
• Lithium ion batteries and products that contain lithium ion batteries are subject to stringent transportation regulations. If you need to ship this product (with the battery included) for service, travel or any other reason, you must see the Troubleshooting section of your manual or contact customer care for shipping instructions.
• Periodically inspect the battery pack for any sign of damage or leakage.
  Do not charge damaged or leaking battery packs, do not allow the liquid to come in contact with skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medicaladvice. Place the battery in a sealed plastic bag and recycle or dispose of safely according to local environmental regulations, or return it to your local authorized iRobot Service Center for disposal.

CAUTION

• Battery usage by children should be supervised. Seek medical advice immediately if a cell or a battery has been swallowed.
  NOTICE

• The battery pack must be removed from the robot before recycling or disposal.

• For best results, only use the iRobot Lithium Ion Battery that comes with the robot.

• Do not use non-rechargeable batteries. Use only the rechargeable battery supplied with the product. For replacement, purchase identical iRobot battery or contact iRobot Customer Care for alternative battery options.

• Always charge and remove the battery from your robot and accessories before long-term storage.

** This symbol on the battery indicates that the battery must not be disposed of with unsorted common municipal waste. As the end-user, it is your responsibility to dispose of the end-of-life battery in your appliance in an environmentally sensitive manner as follows: (1) returning it to the distributor/dealer from whom you purchased the product; or (2) depositing it in a designated collection point The seperate collection and recycling of end- of-life batteries at the time of disposal will help to conserve natural resources and to ensure that it is recycled in a manner that protects human health and the environment. For more information, please contact your local recycling office or the dealer from whom you originally purchased the product. Failure to properly dispose
of end-of-life batteries may result in the negative potential effects on the environment and human health due to the substances in the batteries and accumulators.
Note:** For battery recycling go to call2recycle.org; or call 1-800-822-8837

AUTOMATIC DIRT DISPOSAL

WARNING

• Do not use if the cord or plug is damaged. If appliance is not working as it should, has been dropped, damaged, left outdoors or dropped into water, return it to a service centre.
• Always disconnect your robot from the dirt disposal before cleaning or maintaining it.
• Do not use the dirt disposal as a step.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair and anything that may reduce air flow.
• To properly maintain your dirt disposal, do not place foreign objects inside and ensure that it is clear of debris.
• In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
• Do not allow liquids to get on or into the dirt disposal.
• Do not pour any liquids into the device and do not immerse in water.
• Do not use outdoors or on wet surfaces.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Use only as described in this manual.
• To reduce the risk of electric shock, unplug your dirt disposal before cleaning.
• Keep the dirt disposal and power cord away from heated surfaces.

NOTICE

• Product may not be used with any type of power converter. Use of power converters will immediately void the warranty.
• If you live in an area prone to electrical storms, it is recommended that you use additional surge protection. Your dirt disposal may be protected with a surge protector in the event of severe electrical storms.
• Do not use without dust bag and/or filters in place.

About Your Roomba® Robot Vacuum

About your Clean Base™ Automatic Dirt Disposal

For more information, visit global.irobot.com

Using Your Roomba® Robot Vacuum

Positioning the CleanBase™ Automatic Dirt Disposal Note: Do not place your CleanBase in direct sunlight. Ensure that the area around the dock is free of clutter to improve docking performance.
WARNING: To prevent the risk of your robot falling downstairs, ensure that the Charging Station is placed at least 1.2 metres (4 feet) away from stairs.

Download the iRobot Home App and Connect to Wifi

• Follow the step-by-step instructions to set up your Roomba.
• Set up Precision Vision Navigation™ to avoid obstacles in real time.
• Set an automatic cleaning schedule and customize cleaning preferences.
• Create smart maps to tell your robot where and when to clean.

About Your Automatic Dirt Disposal
While cleaning, your robot will automatically return to the dirt disposal to empty its bin and recharge as needed.
The dirt disposal’s LED indicator will turn solid red when a new bag is needed.
If a clog is detected, the dirt disposal will trigger additional attempts to automatically clear the clog.
Note: If you place your robot on the dirt disposal by hand, it will not empty automatically. In this case, use the iRobot Home App or hold the button down for 2-5 seconds.

White Spiral: charging
Red Spiral: charging, low battery
A solid white light will indicate the battery charge percentage of your robot

• Place the robot on the charging station to activate the battery.
  Note: Your robot comes with a partial charge, but we recommend that you charge the robot for 3 hours prior to starting the first cleaning job. When your robot is fully charged, the light ring indicator will intermittently pulse white at the rear.

• The robot uses a small amount of power whenever it is on the charging station.
  You can put the robot in a further-reduced power state when not in use. To put your robot into reduced power standby mode, remove the dust bin and tap the clean button 5 times. To exit reduced power standby mode, place your robot on the charging station and tap the clean button. For more details on this
  Reduced Power Standby Mode, refer to the FAQ page on our website.

• For long-term storage, turn off the robot by removing it from the charging station and holding down the clean button for 3 seconds with one wheel off the ground. Store the robot in a cool, dry place.
  Cleaning

• Your robot will automatically explore and clean your home. It will return to the charging station at the end of a cleaning job and whenever it needs to recharge.
  Remove excess clutter from floors before cleaning. Use your robot frequently to maintain well-conditioned floors.

• To end a job and send the robot back to its charging station, hold the clean button down for 2-5 seconds. A blue light ring pattern will indicate that the robot is seeking the charging station.

• When your robot detects an especially dirty area, it will engage Dirt Detect™ mode, moving in a forward/backward motion to clean the area more thoroughly. The light ring indicator will flash blue. When the robot senses its bin needs to be emptied, the light ring indicator will illuminate in a red sweeping motion toward the rear.

Care and Maintenance

To keep your robot running at peak performance, perform the procedures on the following pages.
There are additional instructional videos in the iRobot Home App. If you notice the robot picking up less debris from your floor, empty the bin, clean the filter, and clean the brushes.
Care and Maintenance Instructions for Your Robot

2 months
Full Bin Sensor| Clean every 2 weeks| –
Front Caster Wheel| Clean every 2 weeks| Every 12 months
Edge-Sweeping Brush and Multi- Surface Brushes| Clean once a month (twice a month if you have a pet)| Every 12 months
Sensors and Charging Contacts| Clean once a month| –
Camera Window| Clean and inspect once a month| After 30 washes

Note: iRobot manufactures various replacement parts and assemblies.
If you think you need a replacement part, please contact iRobot Customer Care for more information.

• Replacement frequency may vary. Parts should be replaced if visible wear appears.

Emptying the Bin

1. Press bin release button to remove bin.
2. Open bin door to empty bin.
3. Place bin back in the robot.

Cleaning the Filter

1. Remove the bin. Remove the filter by grasping both ends and pulling out.
2. Remove debris by tapping the filter against your trash container.
3. Reinsert filter with ridged grips facing out. Place bin back in the robot.

Important: The robot will not run if the filter is not installed correctly. Replace the filter every two months.

Cleaning the Full Bin Sensors

1. Remove and empty the bin.
2. Wipe the inner sensors with a clean, dry cloth.
3. Wipe the bin door with a clean, dry cloth.

Washing the Bin
Important: Do not wash the filter. Remove the filter before washing the bin.

1. Release the bin, remove the filter, and open the bin door.
2. Rinse the bin using warm water. Note: Bin is not dishwasher safe.
3. Make sure bin is completely dry. Reinsert filter and place bin back in the robot.

Cleaning the Edge-Sweeping Brush

1. Use a coin or small screwdriver to remove the screw holding the Edge-Sweeping Brush in place.
2. Pull to remove the Edge-Sweeping Brush. Remove any hair or debris, then reinstall the brush.

Cleaning the Front Caster Wheel

1. Pull firmly on the front wheel module to remove it from the robot.
2. Pull firmly on the wheel to remove it from its housing (see illustration below).
3. Remove any debris from inside the wheel cavity.
4. Reinstall all parts when finished. Make sure the wheel clicks back into place.

Important: A front wheel clogged with hair and debris could result in damage to your floor. If the wheel is not spinning freely after you have cleaned it, please contact Customer Care.

Cleaning the Multi-Surface Brushes

1. Pinch the brush frame release tab, lift the tab, and remove any obstructions.

2. Remove the brushes from the robot. Remove the brush caps from the ends of the brushes.
   Remove any hair or debris that has collected beneath the caps. Reinstall the brush caps.

3. Remove any hair or debris from the square and hexagonal pegs on the opposite side of the brushes.

4. Remove the bin from the robot and clear any debris from the vacuum path.

5. Reinstall the brushes in the robot. Match the shape of the brush pegs with the shape of the brush icons in the cleaning head module

Cleaning the Sensors, Camera Window and Charging Contacts

1. Wipe sensors, camera window, and charging contacts with a clean, dry cloth.

Important: Do not spray cleaning solution or water onto the sensors or sensor openings.

Care and Maintenance Instructions for Your Clean Base
To keep your dirt disposal running at peak performance, follow these care procedures:

when prompted by the
LED indicator/app.
Charging Contacts Visual Docking Target| Once every month| –
Blower Cover inside canister| Once every month (remove debris from blower cover)| –

Note: iRobot manufactures various replacement parts and assemblies. If you think you need a replacement part, please contact iRobot Customer Care for more information.

Replacing the Bag

1. Lift up on the canister lid to open.
2. Pull up on the plastic card to remove the bag from the can i ster. Note: This will seal the bag so dust and debris cannot escape.
3. Discard the used bag.
4. Install a new bag, sliding the plastic card into the guide rails.
5. Press down on the lid making sure that it is completely closed.
   Note: To achieve optimal performance with your robot and automatic dirt disposal, clean and/or replace your robot’s filter as needed.

Cleaning the Visual Docking Target and Charging Contacts

Inspect the visual docking target and charging contacts to make sure that they are clear of debris. Wipe with a clean, dry cloth.
Important: Do not spray cleaning solution or water onto the sensors or sensor openings.

Removing Debris from Blower Cover
Inspect blower cover for any lint or debris build-up, and wipe with a clean dry cloth to remove.

Troubleshooting

Troubleshooting Your Robot

• Your robot will tell you something is wrong by playing an audio alert and urning the light ring indicator red. Press the clean button or tap the bumper for details. Check the iRobot Home App for further support.
• After 90 minutes of inactivity off the charging station, the robot will automatically end its cleaning job.
• To factory reset your robot, remove the dust bin and hold the clean button down for seven (7) seconds. A sound will let you know when the factory reset has been completed. Press the clean button down once more to confirm.

Battery Safety & Shipping
For best results, only use the iRobot Lithium Ion Battery that comes with your robot.
WARNING: Lithium ion batteries and products that contain lithium ion batteries are subject to stringent transportation regulations. If you need to ship this product for service, travel or any other reason, you MUST follow the below shipping instructions.

• Battery MUST be turned off before shipping.
• Turn off the battery by removing the robot from the charging station and holding down the clean button for 3 seconds with one wheel off the ground. All indicators will turn off.
• Package the robot securely for shipping.
• If you need further assistance, contact our Customer Care team or visit global.irobot.com.

Troubleshooting Your Automatic Dirt Disposal
Your dirt disposal will tell you if something is wrong via an LED indicator on the front of the canister and through the iRobot Home App.

2. Make sure that the bag is securely inserted.
3. If problem persists, remove any debris from the port on the bottom of your robot and the dirt disposal.
Blinking red| There is a leak or
a clog in the dock
evacuation path| 1. Make sure that the canister lid is pushed down and firmly sealed.
Hold the clean button on your robot down for 2-5 seconds to manually empty the bin.
2. Remove any debris from the port on the bottom of your robot and dirt disposal.
3. Unplug the dirt disposal from the wall. Place it on its side and inspect the debris evacuation tube for debris. If necessary, remove the tube to clear any debris

This product has been equipped with a thermal protector designed to protect against damage due to overheating. If the protector operates, the motor will stop running. If this happens, unplug the unit, allow it to cool for 30 minutes, clear any obstructions from the evacuation port and evacuation tube, then plug the unit back in.

Regulatory Information

FCC Supplier’s Declaration of Conformity

iRobot Corporation
Roomba Model: RVE-Y2, ADG-N1

Contains FCC ID: 2AATL-6233E-UUB and contains IC: 12425A-6233EUUB
This device complies with part 15 of the FCC Rules and CAN ICES-003(B) / NMB-003(B).
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

• Changes or modifications not expressly approved by iRobot Corporation could void the user’s authority to operate the equipment.

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules as well as CAN ICES-003(B) / NMB-003(B) Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
  However, there is no guarantee that interference to radio communication will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

• Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than the necessary for successful communication.

• FCC Radiation Exposure Statement: This product complies with FCC §2.1091(b) for mobile device RF exposure limits, set forth for an uncontrolled environment and is safe for the intended operation as described in this manual. Per FCC requirements, maintain a distance of more than 8 inches (20 cm) between any person and the host device (Roomba robot).

• ISED Radiation Exposure Statement: This product complies with the Canadian Standard RSS-102 for mobile device RF exposure limits, set forth for an uncontrolled environment and is safe for the intended operation as described in this manual. Per ISED requirements, maintain a distance of more than 8 inches (20 cm) between any person and the robot.

iRobot Corporation, 8 Crosby Drive,
Bedford, MA 01730 USA. http://global.irobot.com
For battery recycling go to call2recycle.org; or call 1-800-822-8837

iRobot Customer Care

USA & Canada
If you have questions or comments about your dirt disposal, please contact iRobot before contacting a retailer.
You can start by visiting global.irobot.com for support tips, frequently asked questions, and information about accessories. This information can also be found in the iRobot HOME App. If you need further assistance, call the US Customer Care team at 877-855-8593.
iRobot USA Customer Care Hours
Monday to Friday, 9AM — 9PM Eastern Time
Saturday and Sunday 9AM — 6PM Eastern Time
Outside USA & Canada
Visit global.irobot.com to:
Learn more about iRobot in your country
Get hints and tips to improve your product performance
Get answers to questions
Contact your local support center

©2023 iRobot Corporation, 8 Crosby Drive, Bedford, MA 01730, USA. All rights reserved.
iRobot is a registered trademark of iRobot Corporation, Roomba Robot Vacuum, Clean
Base and Dirt Detect are trademarks of iRobot Corporation. Wi-Fi and the Wi-Fi logo are
registered trademarks of Wi-Fi Alliance. Apple and App Store are trademarks of Apple Inc.,
registered in the US and other countries. Google Play is a trademark of Google LLC.
12 For more information, visit global.irobot.com

References

• Call2Recycle | Leading the Charge For Battery Recycling
• Global.iRobot.com
• Find Answers | iRobot

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>