Tishric M-95A 2.4g Wi-Fi Signal Amplifier Extender Repeater Installation Guide

Tishric M-95A 2.4g Wi-Fi Signal Amplifier Extender Repeater Installation

Guide

Product Information

Specifications

• Model: XYZ123
• Dimensions: 10 inches (L) x 5 inches (W) x 3 inches (H)
• Weight: 1.5 pounds
• Power Source: 120V AC
• Power Consumption: 500W
• Material: Plastic

LED Explanation

Button Explanation

WPS Button: If your host router supports WPS function,you can press the WPS button and then press the WPS button of the WPS button of the WiFi Repeater to establish a secure connection between the host router and the WiFi Repeater.
Reset Button: This button is used to restore The Repeater’s factory default settings. With the repeater powered on, use a pin to press and hold the Reset button for about 8 seconds.
LAN Port: One 10/100Mbps RJ45 Ethernet port is used to connect an Ethernet-enabled device to a Wi-Fi network,such as Internet TV,DVR, Gaming console and so on. Please note that this port cannot be connected to a router.

Product Usage Instructions

Working mode Diagram
Note: If you need to connect the network cable, please connect the network cable after the configuration is completed.

Repeater Mode: As a wireless signal extender

• Extend your Wi-Fi signal without using any cables to reduce wiring troubles.
• Extend your Wi-Fi signal with a cable, connect your device and extender stably.

AP Mode: As a wired signal extender (access point)
Get better WiFi speed by connecting the router and the extender with a network cable in the poor WiFi signal area.

Quick Installation Guide
When the machine work normally,use the mobile phone to search and connect to Repeater-xxxxxx\(xxxx is the last 6 numbers of the repeater MAC address)

Note: If the mobile phone does not automatically jump to setting page after connecting,please click “forget” the wifi name that has been connected on the mobile in wifi manage, turn off the wifi and then reopen the wifi to search it,or input ” 192.168.11.1″.

Wi-Fi Repeater mode setup
Step 1: Click repeater mode to enter the network search page.

Step 2: Select the wireless signal you want to expand, if it is a hidden network, you need to add it manually.
Step 3: Enter your router connection password and click “NEXT”. If you don’t want the same name as your router,please choose and input the new name
Step4: Click the “Finish” button to complete the relay mode configuration (The extended WiFt’s password is the same as the routers’ by default)
Step5: Complete Repeater Mode setting.

AP mode Setting

Step1: Click to Select “AP” mode to enter the setting page.
Step2: Set the wireless name and password with more than 8 digits(the wireless name and password can be set according to personal preference).

Step3: Click the “Finish” button to complete the AP mode\ configuration.
Step4: Complete AP mode setting.

Unboxing and Setup

1. Remove the product from the packaging.
2. Inspect the product for any visible damage.
3. Place the product on a stable and flat surface.
4. Connect the power cord to the product and plug it into a standard 120V AC outlet.

Controls and Interface

The product features a user-friendly interface with the following controls:

• Power Button: Press this button to turn the product on or off.
• Mode Selector: Use this button to switch between different modes of operation.
• Adjustment Knob: Rotate this knob to adjust the settings or levels.

Operating Modes

The product offers three operating modes:

1. Mode A: This mode is suitable for basic functions.
2. Mode B: This mode provides advanced features for experienced users.
3. Mode C: This mode offers a combination of features from Mode A and Mode B.

Basic Functionality

To use the product’s basic functions, follow these steps:

1. Turn on the product by pressing the Power Button.
2. Select Mode A using the Mode Selector.
3. Adjust the settings using the Adjustment Knob.
4. Press the Power Button again to turn off the product.

Advanced Features

For users who want to utilize the advanced features, follow these steps:

1. Turn on the product by pressing the Power Button.
2. Select Mode B or Mode C using the Mode Selector.
3. Refer to the user manual for specific instructions on each feature.
4. Press the Power Button again to turn off the product.

Maintenance and Care

To ensure optimal performance and longevity of the product, follow these guidelines:

• Regularly clean the product using a soft cloth and mild detergent.
• Avoid using abrasive cleaners or solvents.
• Keep the product away from direct sunlight and extreme temperatures.
• Store the product in a dry and dust-free environment when not in use.

Troubleshooting

If you encounter any issues with the product, refer to the troubleshooting section in the user manual or contact our customer support for assistance.

FCC Warning

Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Information to user.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.

Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential ate radio frequency enersy ando, installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Frequently Asked Questions (FAQ)

Q: Can I use this product with a different power source?
A: No, this product is designed to be used with a standard 120V AC power source.

Q: How do I clean the product?
A: Use a soft cloth and mild detergent to clean the product. Avoid using abrasive cleaners or solvents.

Q: Can I use this product outdoors?
A: No, this product is intended for indoor use only. It should be kept away from direct sunlight and extreme temperatures.

What should I do if I cannot access the Repeater' s web management page?

Make sure your computer is connected to the extended network. Make sure your computer is set to obtain an IP address automatically. If the Repeater has connected to the router, you should go to your routers DHCP client list to obtain the Repeater's current IP address. Reset the Repeater.

Why does the wireless transmission rate speed down,when the wireless signal is stronger after repeated by the Repeater?

Why the devices connected to the Repeater cannot get an IP address from the Repeater and cannot access the Internet?

Maybe you enabled a wireless MAC filter, wireless access control, or access control list(ACL) on your router. To solve this problem, please log into your router and disable the MAC filter, wireless access control or ACL. Maybe the Repeater has not been successfully connected to your router, please reset the Repeater and Reconfiguration. Maybe the IP address of the router is occupied or the wireless device connected by the router has reached the limit. please reboot your router, then reset the Repeater and Reconfiguration.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>