EVERGREEN IAN 373292_2104 OIL PUMP 12V UOP 12 C1 Instruction Manual

: June 4, 2024
: Evergreen

IAN 373292_2104 OIL PUMP 12V UOP 12 C1
Instruction Manual

IAN 373292_2104 OIL PUMP 12V UOP 12 C1

OIL PUMP 12V UOP 12 C1
Operation and safety notes
Translation of the original instructions

www.lidl-service.com
IAN 373292_2104

Operation and safety notes EVERGREEN IAN 373292_2104 OIL PUMP fig
2

List of pictograms used
CE mark indicates conformity with relevant EU directives applicable to this product.
UKCA mark indicates conformity with relevant Great Britain regulations applicable for this product.
(The UKCA mark logo is valid in Great Britain only .)
OIL PUMP 12 V UOP 12 C1

Introduction

We congratulate you on the purchase of your new product. You have chosen a high-quality product. The instructions for use are part of the product . They contain important information concerning safety, use, and disposal. Before using the product, please familiarise yourself with all of the safety information and instructions for use. Only use the product as described and for the specified applications. If you pass the product on to anyone else, please ensure that you also pass on all the documentation with it.

Intended use

This appliance is intended to pump out engine oil, diesel, and heating oil. It is intended for private use only. The appliance shall not be used for pumping out flammable liquids like gasoline and petroleum, or transmission oil. Pumping out water, chemicals, alkalis, foods, paints, and varnishes is also not allowed.
The appliance is not suitable for continuous operation. It can be continuously operated for a maximum of 30 minutes.
Any other use not mentioned in these instructions may cause damage to the appliance or generate a serious risk of injury.
The user is solely responsible for damage or accidents to other people or their property, which may occur while using the appliance.
The manufacturer accepts no liability for damages caused by improper use.
The appliance is not intended for commercial use.

Scope of delivery

After unpacking the appliance, check if it is complete and if all parts are in good condition.
Remove all packing materials before use.

Oil pump with a battery connection cable
Suction hose
Drain hose
2 hose clamps
Operating manual

Description of parts

Appliance

On/off switch
Pump casing
Battery connecting cable
Positive pole clamp (+) (red)
Negative pole clamp (‒) (black)
Drain hose connector (OUT)
Protective caps
Suction hose connector (IN)

Accessories

Suction hose (Ø 6 mm)
Hose clamp
Drain hose (Ø 12 mm)

Technical data

Model number	UOP 12 C1
Input voltage	12 V ****(direct current)
Power input	60 W
Max . running time tmax	30 min
Max . temperature ϑmax	60 °C
Protection class	III/ ****
IP rating	IPX4

*Output (pump capacity):**
diesel fuel/heating oil……………approx. 1 .5 l/min
engine oil (60 °C)…………………..approx. 0 .2 l/min
Max . discharged head……………..0 .7 m
Max . permissible pressure……………………0 .3 MPa / 3 bar
Weight (incl . accessories)…………………..approx. 890 g
Sound pressure level…………….approx. 70 dB(A)

The capacity may diverge from given data, depending on the temperature and type of oil.

Safety symbols

CAUTION: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
EXCLAMATION MARK:
Indicates a hazardous situation that, if not avoided, could result in property damage.
Please read all safety information and instructions .
Failure to comply with the safety information and instructions may result in, fire and /or severe injuries .
Wear eye protection.
Wear hand protection.
Wear breathing protection.
Pumping direction
Protection class III
Direct current

Safety information

BEFORE USING THE PRODUCT, PLEASE FAMILIARISE YOURSELF WITH ALL OF THE SAFETY INFORMATION AND INSTRUCTIONS FOR USE! WHEN PASSING THIS PRODUCT ON TO OTHERS, PLEASE ALSO INCLUDE ALL THE DOCUMENTS!
In the case of damage resulting from non-compliance with these operating instructions, the guarantee claim becomes invalid!
No liability is accepted for consequential damage! In the case of material damage or personal injury caused by incorrect handling or non-compliance with the safety instructions, no liability is accepted!

WARNING!
DANGER OF DEATH AND ACCIDENTS FOR TODDLERS AND CHILDREN!
Never leave children unsupervised with the packaging material. The packaging material represents the danger of suffocation. Children frequently underestimate the dangers. Please keep children away from the product at all times.

This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Check the appliance, battery cables, and battery terminals for damage before each use. Use only original accessories. Do not operate damaged or altered appliances.
CAUTION! The danger of electric shock! Do not attempt to repair the appliance yourself. In case of malfunction, repairs are to be conducted by qualified personnel only.
Make sure that the appliance is properly installed. Always fasten the hoses with hose clamps to prevent potential spills.
The appliance should only be supplied with a SELV (Safety Extra Low Voltage) corresponding to the marking on the appliance.
When operating vehicle batteries, always follow the advice of the manufacturer of the battery and of the vehicle.
Wear personal protective equipment such as safety goggles, hand gloves, and a dust mask. We recommend the use of acid and alkali-resistant hand gloves. The use of personal protective equipment reduces the risk of injury.
Be attentive and use common sense during operation. Never leave the appliance unattended during use. A moment of inattention may result in serious injury or damage to the appliance and/or vehicle.
Fuels and lubricants can be hazardous to health. Avoid direct skin contact and inhalation of fumes.
CAUTION! The danger of burns! Take special care when working with vehicle batteries .
Battery acid may leak causing serious injuries. If the battery acid gets into contact with the skin or eyes, flush it with water and consult your physician .
Make sure that the vehicle is not parked on sloped ground, otherwise, it might not be possible to pump out all oil. Make sure that the parking brake is engaged.
Grasp the terminals only by the insulated handles. Pay attention to the correct polarity. Connect the positive pole terminal to the positive pole of the vehicle battery and the negative terminal to the negative pole (see “Getting started”).
Do not short-circuit the terminals and/or connecting cables .
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
CAUTION! Risk of fire!
Do not operate the appliance when the engine is switched on or is hot. Do not start the vehicle engine during the pumping process. Never use the appliance for longer than 30 minutes in continuous operation in order to prevent overheating.
CAUTION! Risk of fire! Do not pump oil at a temperature higher than 60 °C.
CAUTION! Risk of fire and explosion! Do not operate the vehicle battery in the proximity of open flames or gases. Do not smoke when operating the vehicle battery Ensure good ventilation in the work area.
CAUTION! Risk of fire!
Do not use the appliance to pump out flammable liquids (like gasoline and petroleum, transmission oil), water, aqueous solutions, other chemicals, alkalis, foods, paints and
varnishes.
Do not operate the appliance dry. The appliance can become damaged due to insufficient lubrication.
Collect the pumped-out oil only in approved oil containers. Do not pump different types of oil into the same container.
Disconnect the appliance from the battery terminals immediately after operation.
Using the appliance for extended periods of time can completely discharge the vehicle battery.
Do not carry the appliance by the connecting cables or the hoses. Keep the connecting cables and hoses away from hot parts of the vehicle or sharp edges.
Store the appliance and the used oil in a dry place and out of reach of children.
Dispose of used oil and soaked rags properly (see “Disposal”).
In order to protect the environment, do not let oils drain into the ground or household drains.
Never use a damaged appliance! Disconnect the appliance from the vehicle and contact your retailer if it is damaged.
Never use accessories that are not recommended by the manufacturer. They could pose a safety risk to the user and might damage the appliance.
Only use original parts and accessories.
This product has been classified as IPX4 and is protected against splashing water from any direction. Do not immerse in water.

CAUTION! Do not immerse the electrical parts of the appliance in water or other liquids. Never hold the appliance under running water.
To prevent damage, let the appliance cool for at least 10 minutes after every 30 minutes of continuous operation.

Getting started

Attaching the hoses

Remove the protective caps 7] (fig . A).
Straighten the suction hose 9] and the drain hose 11].
Put the hose clamp 10] to the end of the suction hose (Ø 6 mm) 9]. Plug the suction hose end onto the suction hose connector 8]. Fasten the hose clamp 10] (Tool: Slotted screwdriver).
Put the hose clamp 10] to the end of the drain hose (Ø 12 mm) 11]. Plug the end of the drain hose onto the drain hose connector 6]. Fasten the hose clamp 10] (Tool: Slotted screwdriver).
Pay attention to the pumping direction on the appliance.

Make sure that the hoses 9], 11] are straightened to avoid damage.

Operation

Start the vehicle and run it for 5–10 minutes to warm up the oil (60 °C is the maximum oil temperature). This reduces the viscosity of the oil and enables it to pump it out more efficiently.
Do not pump the oil when the car engine is running.
Gently insert the suction hose (Ø 6 mm) 9] into the bottom of the oil pan (e .g . by the oil level test opening).
Insert the drain hose (Ø 12 mm) 11] into a container (e .g . oil collecting tray).
Set the on/off switch 1] to the “O” (off) position.
Connect the positive pole clamp (red) 4] to the positive pole (+) of the vehicle battery.
Connect the negative pole clamp (black) 5] to the negative pole (‒) of the vehicle battery.
Turning on: Set the on/off switch 1] to the “I” position. The pumping begins after a short suction period.
Turning off: Set the on/off switch 1] to “O” . Turn the appliance off as soon as oil extraction is over or after 30 minutes of continuous operation.
After each use, pump through some fresh oil to clean the appliance.
Remove the negative pole clamp (black) 5] from the negative pole (‒) of the vehicle battery.
Remove the positive pole clamp (red) 4] from the positive pole (+) of the vehicle battery .
To prevent damage, let the appliance cool for at least 10 minutes after every 30 minutes of continuous operation.
Change the oil filter and refill it with new oil according to the vehicle instructions.
Used oil needs to be disposed of in a way according to “Disposal”.

Cleaning and maintenance

WARNING! During cleaning or operation, do not immerse the electrical parts of the appliance in water or other liquids. Never hold the appliance under running water.
Cleaning

After each use, pump through some fresh oil to clean the appliance.
Clean both clamps 4], 5] with a dry cloth after each use. Make sure there is no adhering battery fluid left on the appliance.
Keep the casing 2] and accessories clean . Do not use abrasive, aggressive, or chemical cleaning agents to clean the surface of the appliance.
In case of oil spillage, clean it with a soft cloth or a paper towel.

Maintenance

Check the hose clamps 10] for a tight fit.
Before each use check the appliance and all its accessories for any visible damage.
Apart from the occasional cleaning, the appliance is maintenance-free.

Storage

When not in use, store the cleaned appliance in a dry, secure location away from children .
The store used oil/diesel in appropriate containers only.

Disposal

The packaging is made entirely of recyclable materials, which you may dispose of at local recycling facilities.
Observe the marking of the packaging materials for waste separation, which are marked with abbreviations (a) and numbers (b) with the following meaning: 1–7: plastics / 20–22: paper and fibreboard / 80–98: composite materials.
The product and packaging materials are recyclable and disposed of it separately for better waste treatment. The Triman logo is valid in France only .
Contact your local refuse disposal authority for more details on how to dispose of your worn-out product.
To help protect the environment, please dispose of the product properly when it has reached the end of its useful life and not in household waste. Information on collection points and their opening hours can be obtained from your local authority. Observe the current regulations for waste oil disposal.

Warranty

The product has been manufactured to strict quality guidelines and meticulously examined before delivery. In the event of product defects, you have legal rights against the retailer of this product . Your legal rights are not limited in any way by our warranty detailed below.
The warranty for this product is 3 years from the date of purchase. The warranty period begins on the date of purchase. Please keep the original sales receipt in a safe location. This document is required as your proof of purchase.
Should this product show any fault in materials or manufacture within 3 years from the date of purchase, we will repair or replace it – at our choice – free of charge to you. This warranty becomes void if the product has been damaged, used, or maintained improperly .
The warranty applies to defects in material or manufacture. This warranty does not cover product parts subject to normal wear, thus possibly considered consumables (e .g . batteries) or for damage to fragile parts, e .g . switches, rechargeable batteries, or glass parts.

Warranty claim procedure

To ensure quick processing of your case, please observe the following instructions:
Please have the till receipt and the item number (IAN 373292_2104) available as proof of purchase.
You will find the item number on the rating plate, an engraving, on the front page of the instructions for use (bottom left), or as a sticker on the rear or bottom of the product.
If functional or other defects occur, please contact the service department listed either by telephone or by e-mail.
You can return a defective product to us free of charge to the service address that will be provided to you. Ensure that you enclose the proof of purchase (till receipt) and information about what the defect is and when it occurred.

Service
Service Great Britain
Tel .:08000569216
E-Mail:owim@lidl.co.uk
Service Ireland
Tel .:1800 200736
Service Northern Ireland
Tel .:0800 0927852
E-Mail:owim@lidl.ie

EC declaration of conformity

IAN: Product Identification: Model Number:
373292_2104 “Ultimate Speed” OIL PUMP 12V HG03271
The object of the declaration described above is in conformity with the relevant Union harmonization legislation:
Directive 2006/42/EC
Directive 2014/30/EU
References to the relevant harmonized standards used or references to the other technical specifications in relation to which conformity is declared:
N° / Parts Directive 2006/42/EC
EN 60335-1:2012/A2:2019
EN 60335-2-41:2003/A2:2010
EN 62233:2008
Directive 2014/30/EU
EN 50498:2010
The object of the declaration described above is in conformity with Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment:
N° / Parts
Directive 2011/65/EU
EN IEC 63000:2018
Name and address of the manufacturer:
OEM GmbH & Co. KG Stiftsbergstrage 1 D-74167 Neckarsulm Germany
This declaration of conformity is issued under the sole responsibility of the manufacturer.
The original declaration of conformity

UK DECLARATION OF CONFORMITY
IAN: Product identification: Model Number:
373292 2104 “Ultimate Speed” OIL PUMP 12V I-1603271
The object of the declaration described above is in conformity with the relevant statutory requirements:
Supply of Machinery (Safety) Regulations 2008
Electromagnetic Compatability Regulations 2016
Restriction to the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012
References to the relevant designated standards used or references to the other technical specifications in relation to which conformity is declared:
N° / Parts
Supply of Machinery (Safety) Regulations 2008
EN 60335-1:2012/A2:2019
EN 60335-2-41:2003/A2:2010
EN 62233:2008
Electromagnetic Compatability Regulations 2016 EN 50498:2010
The object of the declaration described above is in conformity with “The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012”: NV Parts EN IEC 63000:2018
Signed for and on behalf of:
OWIM GmbH & Co. KG Stiftsbergstrage 1 D-74167 Neckarsulm Germany
This declaration of conformity Is Issued under the sole responsibility of the manufacturer.
The original declaration of conformity

For EU market:
OWIM GmbH & Co. KG
Stiftsbergstraße 1
74167 Neckarsulm
GERMANY
Imported for GB market by:
Lidl Great Britain Ltd
Lidl House
14 Kingston Road
Surbiton, KT5 9NU
Model No.: HG03271
Version: 11/2021
IAN 373292_2104