SoftHeat 27210301-T-SL Twin Micro-Fleece Heated Blanket User Manual

SoftHeat 27210301-T-SL Twin Micro-Fleece Heated Blanket

Set up Procedure for Blanket and Mattress Pad

1. Place the blanket or mattress pad on the bed with the “Use and Care” instruction label facing up.

2. Blanket: Place the power supply under the bed on the floor. Blanket connectors should hang off the edge of the mattress. Do not tuck cords between the mattress and the box springs.
   Mattress Pad: Be sure to locate the corners properly. On the mattress pad there should be about 4” of the top fabric hanging over the mattress edge so that the label and connector(s) are located on the vertical surface. This will allow the warming product to fit the mattress properly and keep the connectors away from your head, hands, and arms.

3. Place the controllers near the head of the bed. Queen or King Sizes include an additional power supply and controller as each side operates independently.

4. Blanket : Attach blanket connector cords from the controllers to the connectors at the bottom of the blanket. Do not tuck cords between the mattress and box springs.
   Mattress Pad: Attach pad connector cords from the controllers to the connectors at the head of the mattress pad. Do not tuck cords between the mattress and box springs.

5. Plug in the power supply cord. Use a properly rated UL-listed power strip extension cord if needed.

6. Choose the most comfortable heat setting. The higher the number is set, the higher the amount of heat.

7. Push the button to turn on. Your blanket or mattress pad will then go into “prewarm” mode and will continue to prewarm until it reaches your dial setting.
   Your warming product will then continue to heat at your dial setting all night.

Set up Procedure for Warming Throw

1. Make sure the side of the throw with the “use and care” instruction label faces up.
2. Attach the connector cord from the controller to the bottom of the throw.
3. Make sure that the cords or parts of the heating wire grid are not pinched or tucked-in anywhere.
4. Plug in the power supply cord. Use a properly-rated UL listed power-strip extension cord if needed.
5. Refer to diagram 7 and 8 on how to operate the controller.

Important Information for Warming Throw

This product is not a heated pad. It will not feel warm to your hand’s touch. This warming product is guaranteed to keep you warm. You must sleep on it to experience the warmth.

1.  When ON and operating properly, the controller will be slightly warm to the touch. The higher the dial is set, the warmer it will be. This is completely normal and safe.
2. The power supply or transformer will be warm to the touch when in use and slightly warm when warming product is off. This is normal.
3. This warming product is for home use only—it is not intended for hotel or other institution use.

Care Instructions

• WASHING INSTRUCTIONS NEVER DRY CLEAN OR USE BLEACH ON YOUR WARMING BLANKET, MATTRESS PAD OR THROW!

• MACHINE WASHING
  Disconnect all cord(s). NEVER submerge cords, power supply, or control unit. Place the textile portion in the washing machine and fill it with warm water. Add a small amount of detergent and then let soak for 5 minutes. Agitate on the delicate or gentle cycle for two minutes. Spin on normal speed. Fill the tub for a cool rinse. Agitate for one minute and spin dry. NEVER put your warming product through a wringer.

• HAND WASHING
  Washing your warming product by hand is the best way to make it last. To do this, disconnect all cord(s). Wash your textile separately by hand in a tub of lukewarm (100°F) water using a small amount of mild laundry soap or detergent. Soak the warming product for 5 minutes. Next, gently work the warming product up and down for five more minutes. NEVER rub or scrub. Rinse thoroughly in cool water until all traces of soap or detergent are gone. Squeeze excess water out by hand.
  NEVER twist your warming product.

• DRYING INSTRUCTIONS
  NEVER USE COMMERCIAL DRYERS AT THE LAUNDROMAT – THEY MAY BE EXTRA HOT AND COULD DAMAGE THE WIRING. NEVER PLUG IN YOUR WARMING PRODUCT WHILE DAMP. DO NOT IRON YOUR BLANKET, THROW, OR MATTRESS PAD.

• MACHINE DRY
  To machine dry, put your warming product into a dryer on low heat and allow to tumble until dry. Ensure that your warming product has enough room to tumble freely.

• LINE DRY
  You can line dry your warming product simply by draping the warming product over two parallel clotheslines or a shower rod with the head and foot ends down. Do not reconnect warming products until they are completely dry.

• STORAGE
  Store as you would any other warming product, folded in a dry place.

Important SAFETY Instructions – DO NOT DESTROY

Safetywarningsfor allwarming products asprescribed by UL To operate this warming product properly and safely, there are some critical safety precautions you need to follow. As with all electrical appliances, there is an inherent danger of overheating, fire or personal injury if the product is not used correctly.
Please carefully read what follows before using the warming product.
Never use this warming product with:

• Infants or very small children;
• People with disabilities;
• Anyone who is immobile or cannot operate the controls properly;
• Anyone who is insensitive to heat (e.g. a person with poor circulation);
• Anyone who cannot or will not understand these directions.

Safety Essentials: Setting Up

• NEVER trap or pinch any of the electrical cords in any way. Make sure the cords are NEVER rested between the mattress and box springs.
• The heated area of the warming product should always lie flat on top of the mattress to prevent overheating.
• If the plug does not fit into your outlet, contact a qualified electrician.
• Be sure that the warming product power supply is used only on 120V, 60 HZ current supply.
• Make sure the cord from the controller to the warming product is connected and locked tightly.
• NEVER use your warming product with an airbed, a pull-out sofa or mechanically adjusted bed.
• You may use this warming product with any sheets, mattress pads or other blankets but NEVER in combination with any other electric blankets or electric mattress pads.
• The warming product should never be folded, balled up or bunched in any way when in use. May result in overheating and/or permanent wrinkling of the fabric.
• NEVER use pins in and around the warming product.
• Cats, dogs and other pets should always be kept away from the product, as a sharp claw may result in damage to the heating element.
• Keep the controls away from drafty areas that may become damp or wet, such as an open window.

Safety Essentials: Care and Maintenance

• Always turn off the electric current when the warming product is not in use, either by turning off the controller or unplugging the power supply from the wall outlet.
• Wrapping of the cord around the controls may damage the cord. Loop loosely when storing.
• NEVER iron your warming product.
• NEVER use dry cleaning fluid on this warming product cleaning solvents may damage the wiring insulation.
  If you should observe this warming product operating improperly, discontinue use immediately and call the Perfect Fit Customer Service Department at 800-299-1378 or email to custserv@perfectfitindustries.com.

Troubleshooting

• Q: The lamp on my controller does not light up.
  A: Assure that all the wire connections are tight and that the power supplyv cord is connected to an “energized” socket (try a lamp to verify that the outlet is working properly).

• Q: The controller lamp is lit but the warming product does not heat up.
  A: Test the warming product by folding it over on itself and turning the dial setting to HI. Ensure that the controller lamp is lit. After approximately five minutes, carefully feel between the layers. Never leave the warming product turned on and folded up for more than a few minutes.

• Q: I feel some warmth but not a lot. How warm should this warming product get?
  A: This warming product will provide enough warmth to keep you quite comfortable even in an extremely cold room with only a light blanket on top. You should spend several nights experimenting with the heat settings until you find your personal comfort level. This warming product is not like a heating pad (this amount of heat would be too hot to use all night long). In normal operation, warming products do not feel hot to the touch.

• Q: Can I use a bedspread or comforter over my electric warming product?
  A: You normally will not need more warmth than this warming product will provide. However, you may use any bedding you wish with this warming product except another electric mattress pad, electric blanket or a heating pad (overheating may occur).

• Q: My warming product works fine but then seems to shut off.
  A: The 10-hour automatic shutoff feature may have activated. Simply push the ON button again and your warming product will heat for an additional ten hours or until you turn it off. If ten hours have not elapsed, check that all your connections are tight and the wall outlet is not turned off.

• Q: How much money will this warming product save me on my heating bill?
  A: Your savings will depend upon how many degrees you turn your furnace thermostat down while sleeping. You should save at least 1% of your heating bill for every 1 degree you set your thermostat back at night.

• Q: Does this product have enough electromagnetic field to worry about?
  A: This warming product uses direct current (from the power supply), not alternating current. While some scientists think AC electricity may cause certain health problems, DC electricity has never been known to pose any health problems.

• Q: What is low voltage?
  A: Our warming products use between 14 and 18 volts depending upon the model. Other electric warming products in North America use 120 volts. It would be extremely unlikely, and indeed almost impossible, to receive an electrical shock from this low-voltage warming product.

• Q: Can I sit or lie on my electric warming product?
  A: Just sitting or lying on the warming product will not harm it. Jumping on it or other similar abuse may damage it.

• Q: Why are my power supply and controller warm?
  A: Heat is produced when the 120VAC from your wall outlet is transformed into a nonhazardous low-voltage current. This warmth is completely normal and is nothing to be concerned about. The power consumed is approximately 1 watt (much less than a typical night light).

• Q: My power supply sparked at the wall outlet when I plugged it in.
  A: Yes, many electrical appliances will sometimes “snap” due to the inrush of electricity when first plugged in. This is completely normal and nothing to be concerned about.

FCC

FCC Notification: This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna;
• Increase the separation between the equipment and receiver;
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected;
• consult the dealer or an experienced radio/TV technician for help.

By the rules and regulations of the FCC, changes or modifications to this equipment, not expressly approved in writing by Perfect Fit Industries, Inc. could void the user’s authority to operate this equipment.

Warranty

All Safe and Warm™ products carry a five-year, limited warranty. The Limited Warranty is valid only for, and not transferable from, the original purchaser or gift recipient. No Limited Warranty service is available without proof of purchase or valid gift receipt from an authorized dealer.

Perfect Fit Industries (“PFI”), at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available, a replacement may be made with a similar product of equal or greater value. This is your exclusive warranty. This warranty is valid for the original retail purchaser from the date of the initial retail purchase and is not transferable. Proof of purchase is required to obtain warranty performance. Keep the original sales receipt. Dealers, service centers, or retail stores selling Safe and Warm™ products do not have the right to alter, modify, or in any way change the terms and conditions of this warranty. This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than an authorized service center. Further, the warranty does not cover acts of God, or nature, such as fire, flood, hurricanes, and tornadoes.  Perfect Fit shall not be liable for any incidental or consequential damages caused by the breach of any express or implied warranty. Except to the extent prohibited by applicable law, any implied warranty of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty. Some states, provinces or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state. Under no circumstances will PFI be liable for incidental consequential or punitive damage whether or not the product is found to be covered by this limited warranty.

HOW TO OBTAIN LIMITED WARRANTY SERVICE
If you need Limited Warranty service for your warming product, phone us toll free at 1-800-299-1378 between 8am and 5pm ET, or visit our website www. perfectfitindustries.com/support. Please have your warming product model number, your control model number and sales/gift receipt handy. All Safe and Warm™ products are warranted for five years. Do not return your warming product without a return goods authorization number as it will not be accepted and will be returned at your expense.

NOTE: YOUR WARMING WARMING PRODUCT IS ENGINEERED TO PROVIDE YOU WITH GENTLE, RELAXING ALL-NIGHT WARMTH. IT IS NOT INTENDED TO BE A SUBSTITUTE FOR THE INTENSE PAIN-RELIEVING HEAT OF A HEATING PAD. IT WILL NOT FEEL HOT TO THE TOUCH AS A HEATING PAD DOES.
Before returning this warming product to the retailer, if you need assistance with the set-up or operation, call us first. We can help! Call toll-free at 1-800-299-1378 Monday through Friday 8-5 Eastern Time or write to us at custserv@perfectfitindustries.com.

FAQs

What material is used in the SoftHeat 27210301-T-SL?

The SoftHeat 27210301-T-SL is made with a soft micro-fleece fabric, providing both warmth and comfort.

Can the SoftHeat 27210301-T-SL be machine washed?

Yes, the SoftHeat 27210301-T-SL is machine washable, making it easy to maintain and keep clean.

Is the SoftHeat 27210301-T-SL safe to use overnight?

The SoftHeat 27210301-T-SL is designed with safety features like automatic shut-off and overheat protection, making it safe for overnight use.

Does the SoftHeat 27210301-T-SL have multiple heat settings?

Yes, the SoftHeat 27210301-T-SL comes with multiple heat settings, allowing users to adjust the temperature to their comfort level.

What is the size of the SoftHeat 27210301-T-SL Twin Micro-Fleece Heated Blanket?

The SoftHeat 27210301-T-SL is a twin-sized heated blanket, designed to fit a standard twin bed comfortably.

Is the SoftHeat 27210301-T-SL suitable for children?

While the SoftHeat 27210301-T-SL is generally safe, it's important to supervise children when using any heated blanket.

Does the SoftHeat 27210301-T-SL have a warranty?

The SoftHeat 27210301-T-SL typically comes with a manufacturer's warranty, though the length and terms of the warranty may vary.

How energy-efficient is the SoftHeat 27210301-T-SL Twin Micro-Fleece Heated Blanket?

The SoftHeat 27210301-T-SL is designed to be energy-efficient, using less electricity compared to other heated blankets.

What is the power consumption of the SoftHeat 27210301-T-SL?

The SoftHeat 27210301-T-SL is energy-efficient, but the exact power consumption will depend on the heat setting and usage duration.

Does the SoftHeat 27210301-T-SL have an automatic timer?

Yes, the SoftHeat 27210301-T-SL includes an automatic timer that can be set to turn off the blanket after a certain period.

How long does it take for the SoftHeat 27210301-T-SL to heat up?

The SoftHeat 27210301-T-SL heats up relatively quickly, though the exact time can vary based on the selected heat setting.

Can the SoftHeat 27210301-T-SL be used on other bed sizes?

The SoftHeat 27210301-T-SL is specifically designed for twin beds, so it may not fit other bed sizes as effectively.

Download this pdf manual:SoftHeat 27210301-T-SL Twin Micro-Fleece Heated Blanket User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>