CAMBRIDGE AUDIO SX-60 Stand Mount Speakers Instruction Manual

CAMBRIDGE AUDIO SX-60 Stand Mount Speakers

Product Information

What’s included with the SX-60’s?

The SX-60 Standmount Speakers package includes:

1. 2 x SX-60 speakers
2. Installation guide
3. 8 x rubber pads
4. 2 x foam bungs

Front Panel
The front panel of the SX-60 Standmount Speakers consists of:

1. 1 (25mm) Silk Dome Tweeter
2. 6.5 (165mm) Doped Paper Cone Bass/Mid Driver
3. Front Bass Port

Rear Panel
The rear panel of the SX-60 Standmount Speakers features:

1. +/- Speaker Connection Terminals

Product Usage Instructions

Installation Instructions

1. Using high-quality speaker cable, connect the SX-60 standmount speakers to the speaker terminals on your amplifier. Ensure that you pay close attention to match the polarity of each connection.
2. For optimal results, it is recommended to use speaker stands to mount your SX-60 speakers. Alternatively, the speakers can be placed on a shelf. In either case, leave at least a 5cm space behind the rear of each speaker.
3. If placing the speakers on a desk or close to a wall, you may benefit from using the included foam bass tuning bungs. These can be placed into the front port of each speaker to reduce low-frequency output.
4. Position the speakers and the listening position at an equal distance. However, feel free to experiment until you find the best solution for your space.

Technical Specifications

• Sensitivity (SPL): 89dB
• Frequency Response: 41Hz – 22kHz
• Impedance: 8 Ohms
• Drivers: 1 x 6.5 (165mm) doped paper cone, 1 x 1 (25mm) tweeter
• Crossover: 2 Way
• Recommended Amplifier Power: 20 – 100 Watts
• Porting: 1 Front
• Speaker Dimensions (H x W x D): 340 x 200 x 272mm
• Weight: 5.0kg (11lbs)

Frequently Asked Questions

What is meant by speaker sensitivity?
Speaker sensitivity refers to how loud a speaker can produce sound when given a specific amount of power. It is measured in decibels (dB) and indicates the efficiency of the speaker in converting electrical power into sound.

What is a crossover?
A crossover is an electronic circuit that divides the audio signal into different frequency bands. It directs high frequencies to the tweeter and low frequencies to the bass/mid driver, ensuring each driver handles the appropriate range of frequencies for optimal sound reproduction.

What is impedance?
Impedance refers to the resistance of an electrical circuit to the flow of alternating current (AC). In the context of speakers and amplifiers, impedance is measured in Ohms (Ω) and represents the load placed on the amplifier by the speakers. It is important  to match the impedance of the speakers with the amplifier’sspecifications to ensure proper functioning and avoid damage to the equipment.

Troubleshooting
If you encounter any issues with your SX-60 Standmount Speakers, please refer to the troubleshooting section of the user manual or contact our customer support for assistance.

puJSM=ptandmount Speakers

Last updated : December 7, 2022 01:32. Revision #9807

Introduction

Last updated: January 19, 2023 01:56. Revision #9808
Thank you for purchasing these Cambridge Audio SX-60 stand mount loudspeakers. We hope that you enjoy many years of listening pleasure from them. Your loudspeakers can only be as good as the system it is connected to. Please do not compromise on your amplifier or cabling. Naturally we particularly recommend amplification from the Cambridge Audio range, which has been designed to the same exacting standards as our loudspeakers. Your dealer can also supply excellent quality speaker cable to ensure your system realises its full potential.
Thank you for taking the time to read this manual; we do recommend you keep it for future reference.
© Copyright Cambridge Audio Ltd .
For upcoming news on future products, software updates and exclusive offers, make sure you register your product at http://www.cambridgeaudio.com/register

What’s included with the SX-60’s?

Last updated: January 19, 2023 01:56. Revision #9809

1. 2 x SX-60 speakers.
2. Installation guide.
3. 8 x rubber pads.
4. 2 x foam bungs.

Front panel

Last updated: January 19, 2023 01:57. Revision #9810

1. 1” (25mm) Silk Dome Tweeter.
2. 6.5 ”(165mm) Doped Paper Cone Bass/Mid Driver.
3. Front Bass Port.

Rear panel
Last updated: January 19, 2023 01:57. Revision #9811

Installation instructions

Last updated: January 19, 2023 01:57. Revision #9812

1. Firstly, using high quality speaker cable connect the SX-60 standmount speakers to the speaker terminals on your amplifier. Ensure that you pay close attention to match the polarity of each connection.
2. For the best results we would recommend using speaker stands to mount your SX-60 speakers. Alternatively, the speakers can be placed on a shelf, and in either case we would suggest leaving at least a 5cm space behind the rear of each speaker.
3. If placed on a desk, or close to a wall you may benefit from using the included foam bass tuning bungs. These can be placed into the front port of each speaker to reduce the low frequency output.
4. Finally, when positioning, we would suggest that the distance between speakers and the listening position is equal. However, we would encourage experimentation until you find a solution that works for your space.

Technical Specifications

Last updated: January 19, 2023 01:57. Revision #9813

• Sensitivity (SPL)
  89dB

• Frequency Response
  41Hz – 22kHz

• Impedance
  8 Ohms

• Drivers
  1 x 6.5” (165mm) doped paper cone.
  1 x 1” (25mm) tweeter.

• Crossover
  2 Way

• Recommended Amplifier Power
  20 – 100 Watts

• Porting
  1 Front

• Speaker Dimensions (H x W x D)
  340 x 200 x 272mm.

• Weight
  5.0kg (11lbs)

Frequently asked questions

Last updated: January 19, 2023 01:57. Revision #9814

What is meant by speaker sensitivity?

Speaker sensitivity is the level produced by the speaker at one meter, when supplied with one watt of power from an amplifier. It’s a way of describing how well the speaker produces acoustic energy, based on a given input. The level is measured in dB SPL – this shorthand for ‘sound pressure level’ – sound is basically fluctuations in air pressure, so any time you see SPL, this means ‘sound in the real world’. So, let’s say we have a speaker with an 87dB sensitivity, and a speaker with a 90dB sensitivity – the 90dB speaker is going to be considerably louder, as every 3dB added represents a doubling of power.

What is a crossover?

Most speakers will have multiple drivers. A driver is sometimes called a transducer, which is a device that turns one type of energy into another – in this case, electrical energy to sound energy. In a loudspeaker, it is often the case that we might want multiple drivers – one to handle low-end, one to handle the mid-range, and one to handle the treble. This latter driver is often called a tweeter. To get the benefit of this arrangement, we need to split the signal into different frequency components. The circuit that does this is called a crossover.

What is impedance?

You will often see impedance mentioned when researching speakers, and amplifiers. Impedance is basically resistance measured at a given frequency, given as a value in Ohms (Ω), and is incredibly important to consider when setting up an audio system as it determines the ‘load’ placed on an amplifier by the speakers. For example, let’s say we have an amplifier that is rated to deliver 100W into an 8Ω speaker load. If we were to then use speakers with an impedance of 4Ω with the same amplifier, the amp would then need to supply 200W as a halving of the impedance results in a doubling of the required power due to the reduction of the load on the amplifier.

In a situation such as this, if the amp can’t supply the required power for a lower impedance, then it can result in overheating, and damage to the amplifier and speakers.
For this reason, it is important to pay attention to amplifier specifications, and suggested impedance ratings.

Troubleshooting

Last updated: January 19, 2023 01:57. Revision #9815

No sound through one or both channels.

• Check that the amplifier is turned on.
• Ensure that the correct input source is selected on the amplifier.
• Confirm that all connections between the amplifier and loudspeakers are secure.
• Check that the connections between the source equipment and amplifier are secure.
• Check the polarity of the loudspeaker connections.
• Check that the volume control is set correctly on the amplifier.

There is distorted or inconsistent sound.

• Confirm that all connections between the amplifier and loudspeakers are secure.
• Check the polarity of the loudspeaker connections.
• Check that the connections between the source equipment and amplifier are secure.

References

• Register your product | Cambridge Audio US

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>