LOMTAP LPUS010 Backdrop Support System And 65W 5500K Softbox Umbrellas Light Kit User Manual

LOMTAP LPUS010 Backdrop Support System And 65W 5500K Softbox Umbrellas

Light Kit

SAFETY PRECAUTIONS

1. Become thoroughly familiar with this product before use. Run through at least one practice assembly and breakdown before you schedule a shoot.
2. Never leave the lighting unsupervised when in use. Keep children or incompetent persons away from lighting equipment.
3. lf the power cords show signs of wear or damage. they should be replaced or repaired by a qualified electrician before use.
4. Wait until the bulbs are completely cool before touching or removing them.
5. Never use it in a wet environment. Never let the product touch the water.
6. Never touch the product when your hands are wet.
7. Never move the appliance by pulling the cord. Make sure the cords do not come in contact with bulbs. Do not wind the cord around the appliance.
8. Place stands/tripods on a flat surface to prevent toppling.
9. Do not touch the metal parts near the bulbs while in use, these parts may become very hot.
10. Do not let the umbrella touch the light bulb when in use. Light bulbs will get hot and can ruin the softbox or start a fire.
11. Remember to turn off the power switch before replacing the lamp.

HOW TO REMOVE POLYESTER CREASES

• Firstly, place the polyester fabric on the flat and hard stuff, and spread it flat.
• Tips: Usually, this processing method is for the hydrophilic polyester fabric.
• Secondly, find a wet towel and wipe the fabric gently.
• Note: Do not make the towel too wet, wipe the winkles several times with the towel.
• Thirdly, find something that sizes almost like the polyester fabric, such as a bed sheet, and press it on the fabric.
• Tips: You can put all hydrophilic polyester fabrics together to save time and effort. It might need to press one day or half a day.
• Note: It is not recommended that you wash the fabric, the colour will not be as bright as before after washing. Do not iron the polyester fabric, it may scorch.

5 2m light stand(A) 2 33inch white umbrella(B) 2 60cm octagonal single box(C)
2 single light head(D) 5 65W bulb(E) 1 33inch black silver umbrella(F)
2 33inch black gold umbrella(F) 1 2X3m background G+J) 3 1.6X3m fabric backdrop (H)
6 clamps(l) 1 carry bag(K) 160cm 5 in 1 reflector (L) 1 bracket barM) 1 reel(N)
1 60cm octagonal single box) 1 sandbag(P)

PRODUCT LIST

Installation Instruction

Reflecting umbrella installation steps

1. Extend the stand to a suitable height.
2. Lose the lock and raise the pole.
3. Install the light head on the light stand holder.
4. Install the bulb on the lamp holder.
5. Place the umbrella between the lamp holders.
6. Finish

Installation Instruction
Light stand and soft box’s installation steps:

1. Extend the stand to a suitable height.
2. Lose the lock and raise the pole.
3. Lose the second lock and raise the pole.
4. Install the softbox on the light stand holder.
5. Open the softbox, and push the attachment with the interface to the end.
6. Install the bulb on the lamp holder.
7. Put the soft cloth outside of the box
8. Finish

Installation Instruction
Cantilever mounting steps:

1. Extend the stand to a suitable height.
2. Lose the lock and raise the pole.
3. Lose the second lock and raise the pole.
4. Put the wheel on the stand.
5. Release the wheel button.
6. Choose the right hole and put the bar into the wheel.
7. Release the wheel and adjust the length of the bar.
8. Fasten the softbox on the bar.

2X3m background installation steps

1. Extend the stand to a suitable height
2. Lose the lock and raise the pole
3. Lose the second lock and raise the pole
4. Press the button and align orientation, then connect each other
5. Unscrew the knob of the stand
6. put the pole with holes to the top of the stand
7. Fasten the knob
8. Use the clamp to fix the backdrop at the crossbar
9. Finish

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>