DIVDOU 904 Keyless Entry Door Lock Instruction Manual

OPERATION MANUAL
KEYLESS DEADBOLT LOCK

Details

Parameters

Model:
904/905/906/907
Material:
Aluminum Alloy+PC+Silicagel
Available thickness:
35mm ~ 50mm
Unlock way:
Password/Key| Power supply:
4*AA alkaline batterys
Emergency Supply:
USB(Type-C Interface)
Working voltage: 6V
Alarm voltage: 4.8V
Code capacity:
Master code:10sets
User code:40sets
One-time code:10sets
---|---

Parts list

Installation

1. According to the template, hole in the door and door frame.

2. According to the demand, adjust the size of the deadbolt.

3. Put the deadbolt into the hole digged on the door.
   Fix it on the door with two self-tapping screws.

4. Turn the follower and keep the latch bolt out.

5. Turn and keep the spindle in a vertical. Please make sure the latch bolt is fully retracted (in the unlocked position) before installation

6. Insert the Exterior Assembly into the door hole. Route the cable below the latch.

7. Wear the cable into the square hole of the mounting plate.

8. Fix the mounting plate on the door with two pan head screws.

9. Turn the knob left or right base on the position of the latch bolt .

10. If the latch bolt is on the left, rotating knob to the left as shown .

11. Connect the cable and ensure connection is tight. .

12. Fix the Interior Assembly on the mounting plate with three screws .

13. Install 4 pcs AA alkaline battery

14. Install the battery box.

15. Turn the knob to test lock and unlock. Check the completion.

16. Twist the back knob manually to extend the lock bolt and keep it extended. Refer to the following settings to set the locking direction.

Set up

After the installation is completed, it is necessary to correct the locking direction of the door lock through the “Self-test Function” of the device:

1. Keep the door open, twist the back knob manually to extend the lock bolt and keep it extended.
2. Press the key   , and the device will automatically adjust the locking direction.
3. After the adjustment is completed, the lock bolt will automatically retract and become the unlocked state, otherwise perform the above operation again.
4.  If the device enters the user, it needs to verify the master code or ingerprint before performing the “Self-test Function” .

Note:

1. The master code is “ 123456 ” under factory default conditions. After adding master, the default code becomes invalid.
2. If there is no master, the default code has administrator privileges.
3. Users can set a 6-8-digit code.
4. Users can prevent the code from being exposed to strangers by entering random numbers before and after the code, and the number of digits does not exceed 40.
5. The “ ” key has function of locking and returning , and the “ ” key has the function of unlocking and conirming. Users can also unlock and lock by verifying ingerprint.
6. If you enter the wrong code or ingerprint 5 times in a row, the system will be locked for 3 minutes.
   This state can be released after the time is up or the power is cut off.

Instructions(press “ ” or timeout to exit)
Add master code or ingerprint:

1. Press .
2. Verify the master code + “ ” conirm or verify the master ingerprint.
3. Enter the master code + “ ” twice in a row or enter ingerprint 5 times.
4. 10 master codes or ingerprint can be added, and the location number range is 001-010.
5.  The location number of the irst master code or ingerprint added is 001 and so on.

Add user code or ingerprint:

1. Press .
2. Verify the master code + “ ” conirm or verify the master ingerprint.
3. Enter the user code + “ ” twice in a row or enter ingerprint 5 times.
4. 40 user codes or ingerprint can be added, and the location number range is 011-040
5. The location number of the irst user code or ingerprint added is 011 and so on.

Add a one-time code:

1.  Press “ .
2. Verify the master code + “ ” conirm or verify the master ingerprint.
3. Enter the one-time code + “ ” twice in a row.
4.  The one-time code can only open the lock once, and the code will be automatically invalidated and deleted after use.
5. 10 one-time codes can be added.

Delete user code (There are three ways):

1. Press .

2. Verify the master code + “ ” conirm or verify the master ingerprint.

3. Enter the unneeded code or ingerprint + “ ” .

4. Enter the location number of the unneeded code or ingerprint + “ ” .
   (For example, 002 represents the second master code, 012 represents the second user code)

5. ‘Enter “0000” + “ ” to delete all user codes or ingerprint except the master code or ingerprint.

6. Master code or ingerprint need to be kept at least one.

7.  The newly added code and ingerprint will be illed to the front position.

Vacation mode:

1. Press .
2. Verify the master code + “ ” conirm or verify the master ingerprint.
3. When vacation mode is enabled, no user code or ingerprint other than the master will be able to open the door until the mode is disabled.

Silent mode:

1. Press “ .
2. Verify the master code + “ ” conirm or verify the master ingerprint.
3. Enable and disable silent mode.

Delayed auto-lock function:

1. Press .
2. Verify the master code + “ ” conirm or verify the master ingerprint.
3. Enter the delay auto-lock time + “ ” .
4. The time can be set for 5-30 seconds / input “0” + ” ” to disable the delay automatic locking function.

Self-test Function:

1. Keep the door open, twist the back knob manually to extend the lock tongue and keep it extended.
2. Press the , and the device will automatically adjust the opening direction.
3. Verify the master code + “ ” conirm or verify the master ingerprint.
4. After the adjustment is completed, the lock tongue will automatically retract and become the unlocked state, otherwise perform the above operation again.
5. When the device cannot be used normally, it can be adjusted to the normal state through the

“Self-test Function” .
Restore to factory default settings:
Method 1:

1. Press and hold the reset button 5 seconds through the “ Reset-PIN ” until a long beep is heard.
2. Release the reset button.
3. The factory default settings are restored successfully.

Method 2:

1. Press  .
2. Verify the master code + “ ” conirm or verify the master ingerprint.
3.  The factory default settings are restored successfully.

Functions

1. Add mastercode: Default Settings 123456
   ● 10 master codes or fingerprin t can be added, and the location number range is 001-010.
   ● The location number of the first master code or fingerprint added is 001 and soon.

2. Addusercode: Default Settings No
   ●  40 user codes or fingerprint can be added, and the location number range is 011-040.
   ● The location number of the first user code or fingerprint added is 011 and so on.

3. Addaone-time code Default Settings No
   ●  The one-time code can only open the lock once
   ●  10 one-time codes can be added.

4. Delete user code: Default Settings /
   ●  Enter the unneeded code or fingerprint + “ ” confirm.
   ● Enter the location number of the unneeded code or fingerprint + “ ”” confirm.
   ● Enter “0000” + “ ” key to delete all user codes or fingerprint except the master.

5. Vacation mode: Default Settings Off
   ●  No user code or fingerprint other than the master will be able to open the door until the mode is disabled

6. Silent mode: Default Settings off
   ●  Enable and disable silent mode.

7. Empty

8. Delayed auto-lock: Default Settings Off
   ● Enter the delay auto-lock time + “ ” confirm.
   ● The time can be set for 5-30 seconds
   ● input “0” + “ ” key to disable the delay automatic locking function

9. Self-test Function: Default Settings \
   ● After the installation is completed, it is necessary to correct the locking direction of the door lock through the “Self-test Function” of the device.
   ● When the device cannot be used normally, it can be adjusted to the normal state through the “Self-test Function”
   0. Restore to factory default settings Default Settings Above
   ● Press and hold the reset button 5 seconds through the“ Reset-PIN ”.
   ● Press + Verify the master code or fingerprint + “ ” confirm.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>