HelloBaby HB30 2.4GHz Digital Wireless Video Baby Monitor User Manual

HelloBaby HB30 2.4GHz Digital Wireless Video Baby Monitor

PRODUCT INFORMATION

Model : HB30

The pictures are for reference only, please subject to practicality.

www.hellobaby.net.c
service@hellobaby.net.cn

Thank you for purchasing the HB30 Baby Monitor. With our baby monitor, you can see and hear your baby sleeping or playing in their room anytime. Please retain your original dated sales receipt for your records. For warranty service of your product, you will need to provide a copy of your dated sales receipt to confirm warranty status. Registration is not required for warranty coverage.

Please make sure the following included in your package

• Parent unit x 1
• Camera unit x 1
• User manual x 1
• Wall-mounting kit x 1
• Power Adapter x 2

SAFETY INSTRUCTIONS

• CAUTION :
  Keep the device away from children.

• Strangulation Hazard:
  Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3ft (0.9m) away). Never use extension cords with AC Adapters. Only use the AC Adapters provided.

• Choking hazard:
  This product contains small parts, please be careful when unpacking and assembling the product.

• Read and keep to instructions:
  All the safety and operating instructions should be read before the video baby monitor is operated. This product cannot replace responsible adult supervision.

• Water and moisture :
  This product is designed for indoor use only. The unit should not be exposed to rain, moisture, dripping, or splashing. No objects filled with liquid should be placed on top of, or beside the product, such as a glass or vase. This item should not be used near water.

• DO NOT:
  Use the appliance if the cord or plug is damaged. If your baby monitor is not operating properly or has suffered any damage, contact the “Videotimes” service center to request inspection and repair of the appliance to avoid any possible risk.

• DO NOT:
  Do not attempt to repair or adjust any of the electrical or mechanical functions of the unit. Otherwise, the guarantee will be made void.

• Ventilation:
  This baby monitor should not be used on a bed, sofa, rug, or similar surface that may block the ventilation openings, or be placed in an enclosed area such as a bookcase or drawer that may impede airflow.

• Keep away from sources of heat :
  This unit should not be exposed to direct heat sources such as a candle, radiator, heat register, stove, or other appliance that emits heat. The unit should not be left in direct sunlight.

• Power source:
  This unit should only be used with the AC power adapters included in this package (rated 5V 1A).

• Damage requiring service :
  This unit should be serviced by qualified personnel only when:

  • Objects have fallen or liquid has been spilled into the product;
  • The units have been exposed to rain;
  • The units do not appear to operate normally or exhibit a distinct change in performance
  • The units have been dropped or the enclosure damaged;

WARRANTY TERMS
We offer a one-year warranty from the original purchase date against defects in workmanship and materials. If you have warranty or support issues, please contact our after-sales service via email.

INSTALLATION GUIDELINES

• To use your parent unit and camera unit together, you have to establish a radio link between them, and the range will be affected by environmental conditions.
• Any large metal object, like a refrigerator, a mirror, a filling cabinet, metallic doors, or reinforced concrete between the baby and parent unit may block the radio signal.
• The signal strength may also be reduced by other solid structures, like walls, or by radio or electrical equipment, such as TVs, computers, cordless or mobile phones, fluorescent lights ,or dimmer switches.
• Use of other 2.4GHz products, such as wireless networks (Wi-Fi routers), Bluetooth systems, or microwave ovens, may cause interference with this product, so keep the baby monitor away at least 5ft (1.5m) from such products, or turn them off if they cause interferences.

PLACEMENT OF THE BABY MONITOR
The camera can be placed on the desktop or mounted on the wall. Don’t place the baby monitor on soft quiltsor blankets or in the corners of cupboards, shelves, etc; Keep the baby monitor away from heat sources such as radiators, chimneys, cookers, and direct sunlight; Keep the baby unit away from TV sets, microwave oven and radios. If interference occurs, move the camera to elsewhere;

• Place the camera within 6 feet (2 meters) of the area being monitored for optimum performance.

GETTING STARTED

TURN ON THE BABY UNIT:

1. Insert the DC plug of the power adapter into the DC jack on the side of the Baby Unit;
2. Insert the other end of the power adapter into a suitable electrical outlet;
3. Once the adapter is connected, the power LED will light up;

TURN ON THE PARENT UNIT:

1. Insert the DC plug of the power adapter into the DC jack on the side of the parent Unit;
2. Insert the other end of the power adapter into a suitable electrical outlet;
3. Press and hold the power key for 3 seconds on the front of the parent unit;
4. One the parent unit is on, the power LED will light up and the image will display on the LCD;

INFRARED NIGHT VISION (AUTOMATIC)
The infrared night vision function allows the camera to pick up images in dark or low-light conditions. In this mode, only black and white images will be displayed on the monitor, the optimum image lies in where the baby unit is 6ft (2m) away from the object. The camera is in night vision mode, the icon will be displayed on the top of the screen.

PRODUCT OVERVIEW

ICONS OVERVIEW:

PARENT UNIT OVERVIEW:

BABY UNIT OVERVIEW:

KEY OPERATION

POWER SAVE/SCREEN OFF
Short press the power key to turn on / off the screen.

VOLUME ADJUSTMENT
Press the key to increase the volume; Press the key to decrease the volume;

BRIGHTNESS ADJUSTMENT
Press the key to decrease the brightness; Press the key to increase the brightness;

CAMERA VIEW / SCAN
Press the Scan key to view/scan the camera; During scan mode, the scan icon will be displayed on the top of the screen. Each camera’s video will stay on the LCD for around 10 seconds and then turn to the next camera alternately;

DIGITAL ZOOM & PAN / TILT
Press and hold the key for around 2 seconds to operate Zoom in/out: The Zoom mode, press the key to Pan left; press the key to Pan right; press the key to tilt up; press the key to tilt down; During digital zoom mode, the zoom icon will be displayed on the top of screen.

Warm reminder : If you want to adjust the volume/Brightness, you have to exit the Zoom mode before you operate it.

MENU OPERATION

PAIRING THE CAMERA AND PARENT UNITS
The baby unit is pre-registered to your parent unit. You do not need to register it again unless the baby unit loses connection with the parent unit. To re-register your baby unit or register a new baby unit, follow the steps below:

Note : The camera icon with “ ” means it is well registered. You should select and pair with the camera icon without the ” ” sign.

ADD CAMERA

1. Press the MENU key then the menu will pop up;
2. Press the key until the camera icon is selected by the red box;
3. Press the @ key to enter into sub-menu, then press the key to select your desired camera;
4. Press the key to enter into the sub-menu; Press the key to select then press the OK key;
5. When the icon is displayed on the LCD screen, press the PAIR button on the back of the Amera;
6. Once paired, the Successful pairing icon shows on the LCD screen; 7. If fails. repeat the above steps.

DELETING A CAMERA

1. Press the MENU key and the menu will pop up;
2. Press the key until the camera icon is selected by the red box;
3. Press the key to enter into sub-menu; then press the key to select your desired camera;
4. Press the key to enter the sub-menu; Press the key to select then press the OK key;
5. Press the key to select .
6. Press the key to confirm;
7. Press the key to Exit.

ALARM SETTING
You can use the alarm to remind yourself to feed your baby / change your diaper/sleep, etc.

1. Press the button and the menu bar will pop up.
2. Press the key until the alarm icon is selected by the red box.
3. Press the key to enter into sub-menu, Press the key to select the alarm time you need;
4. Press the  key to confirm;
5. Press the key to Exit.
   • Note 1 : The minimum unit is 0.5 hours. The maximum setting is 5 hours (7 levels).
   • Note 2: Once the alarm is turned on, an alarm icon will display on top of the screen.
   • Note 3 : The alarm default setting is OFF.
   • Note 4 : When the alarm is ringing, press any key on the parent unit to turn the alarm off.
   • Note 5 : If you don’t turn off the alarm, the alarm will ring for 1 minute. After three minutes the alarm will ring again for 1 minute. The alarm will ring three times in total, after this the alarm goes off.

VOX SETTING

This mode allows you to control the sound activation of your baby unit. If there is no sound around the baby unit within 30 seconds, it will stop audio transmission and turn off the screen of the parent unit. When the baby unit detects any sounds louder than the sensitivity level, it will start transmitting the signal to the parent unit again and turn on the screen of the parent unit. To change the VOX level, please follow the below instructions.

1. Press the MENU ( ) key then the menu will pop up;
2. Press the key until the VOX icon is selected by the red box.
3. Press the key to enter into sub-menu, then press the key to select the desired level;
4. Press the key to confirm;
5. Press the key to Exit.
   • Note : is a Low sensitivity level, the baby has to make a lot of sounds before the VOX function will be activated;
   • Note : mis middle sensitivity level;
   • Note : is a High sensitivity level, the baby doesn’t have to make a lot of sound before the VOX function will be activated;

LANGUAGE SETTING

1. Press the MENU key and the menu will pop up.
2. Press the keys until the language icon is selected by the red box;
3. Press ) the key to enter into sub-menu, then press key to select the language you need;
4. Press the key to confirm;
5. Press the key to Exit.

TECHNICAL DATA

Frequency|

2403.S-2475.SMHz

---|---

Power Adaptor

| Parent Unit: Input: 100-240VAC 50/60Hz

Output: SV DC lA

Camera Unit: Input: 100-240VACS0/60Hz

Output: SV DC IA

Operating Range

| Up to 800ft (245m) outdoor line of sight

Up to 165ft (SOm) indoor

Display| 2.4″ TFTLCD
Battery (Parent Unit)| Li-ion 3.7V 950mAh (3.SlSWh)
Battery Life| Up to 6 hours
Camera unitandparent

unit RF power I for CE)

| less than 20dBm

Operation environment

| Operation Temperature: +32f~+104F(0°( ~40°() Battery Charging Temperature: +SOF–+104F(10°(~40°()
Relative Humidity: 15%-85%

TROUBLESHOOTING

No reception on the monitor

| • The power adapters may not be properly connected;

• Confirm the camera and monitor are ON;

• Camera may be far away fromthe monitor;

• Camera and monitor may not be properly paired; follow PAIRING instructions;

---|---

Interference or poor reception

| •  Move the monitor close to the camera;

•  The camera or monitor may be placed too close to many metal objects;

•  Other electronic devices may be interfering with the signal;

•  The battery power is runninglow;

Audio feedback (high pitched noise)| • The camera and monitor may be placed too closed;

• The volume on the monitor may be set too high;

Frozen Picture on Screen

| • Repower the baby unit (plug out the adapter, then plug it into the socket again);

• Press the RESET key at the back of parent unit

MAINTENANCE

• Clean your baby monitor with a slightly damp or anti-static cloth.
• Never use cleaning agents or solvents.

DISPOSAL GUIDE FOR BATTERY AND PRODUCT

• Do not attempt to repair or adjust any of the electrical or mechanical functions of the unit;
• Remember to dispose of the product in an environmentally responsible way;
• For proper collection and processing of these products, take them to the collection points designated by local authorities. You can also contact the store where you purchased the product.

Improper or incorrect use of batteries may cause corrosion or battery leakage, which could cause personal injury or damage to property. Use only the types of batteries which are indicated in this manual.

CAUTION: Risk of Fire and Burns. Do Not Open, Crush, Heat Above 45 degrees C, or Incinerate. Follow the Manufacturer’s Instructions.

• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;
• Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas;
• A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
• The battery shall not be exposed to excessive heat such as sunshine, fire, or the like;

FCC & ISDE Statement

This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

This equipment complies with Canada’s radiation exposure limits set forth for an uncontrolled environment

Radiation Exposure Statement for camera
This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

S AR Statement for Monitor

Specific Absorption Rate (SAR) information:
This Monitor meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. ISED RF Exposure Information and Statement The SAR limit of Canada (ISED) is 1.6 W/kg averaging over one gram of tissue.

Device types:
The monitor has also been tested against this SAR limit. This device was tested for typical body-worn operations with the back of the Monitor kept 0mm from the body. To maintain compliance with ISED RF exposure requirements, use accessories that maintain a 0mm separation distance between the user’s body and the back of the Monitor. The use of belt clips, holsters, and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with ISED RF exposure requirements and should be avoided.

Declaration of Conformity (DOC)
Hereby, Videotimes declares that the radio equipment type is in compliance with RED Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available on the website: www.hellobaby.net.cn

Model : HB30
Responsible Party(US): Startline LLC
Add : 22 Hazelwood Drive, Jericho, NY 11753
Tel : 1-516-681-3729
Authorized UK Representative ( UK ): APEX CE SPECIALISTS LIMITED
Add : 89 Princess Street, M14HT, UK  info@apex-ce.com Shenzhen Videotimes Technology Co., Ltd 701, Building 3, No. 1, Zhenhan Road, Gankeng Community, Jihua Street Office, Longgang District, Shenzhen

Risk Group 1

WARNING IR emitted from this product. Do not stare at the operating lamp
Product tested against EN62471

WARNING
Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9 m) away). Do not remove this tag.

MADE IN CHINA

Documents / Resources

| HelloBaby HB30 2.4GHz Digital Wireless Video Baby Monitor [pdf] User Manual
HB30, HB30 2.4GHz Digital Wireless Video Baby Monitor, 2.4GHz Digital Wireless Video Baby Monitor, Digital Wireless Video Baby Monitor, Wireless Video Baby Monitor, Video Baby Monitor, Baby Monitor, Monitor
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>