NLBFOU 18 Inch Flooring and Siding Cutter Instruction Manual

NLBFOU 18 Inch Flooring and Siding Cutter

SAFETY RULES FOR THE FLOORING CUTTER

WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY! USING THIS MACHINE WITH RESPECT AND CAUTION WILL CONSIDERABLY LESSEN THE POSSIBILITY OF PERSONAL INJURY.

1. READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE OPERATING THE NLBFOU FLOORING CUTTERS.
2. If you are not thoroughly familiar with the operation of NLBFOU flooring Cutter, obtain advice from a qualified instructor or call.
3. Stay alert. Do not operate while under the influence of drugs, alcohol, or medication.
4. Always wear safety approved eye protection with side shields.
5. Keep work area free of debris.
6. Keep children and unauthorized persons away from the NLBFOU flooring Cutter and work area.
7. Make sure tool is secure. Operate only on a firm substrate or solid stand.
8. Use the right tool. Do not force the NLBFOU flooring Cutter or use it for a job for which it was not designed; use only on approved materials.
9. Keep the blade sharp. A dull blade will not perform properly.
10. Always keep hands away from blade while operating or carrying the cutter.
11. Do not alter or misuse this tool. The NLBFOU flooring Cutter is precision built; modifications not specified in this manual may result in a dangerous and unsafe environment.
12. Maintain the NLBFOU flooring Cutter with care. Keep Blade sharp and clean. Follow instructions for changing accessories.
13. Use only recommended accessories. The use of improper accessories may be hazardous and cause injuries.
14. Never leave the NLBFOU flooring Cutter unattended. Secure the handle with the lock chain when not in use.

 Please confirm the purchase model before installation.

Installation of the cutter

Step 1

Align the machine head with the panel

Step 2

Install main engine screws, do not tighten .

Notice:

L-shaped wrench 4mm

If you found spare screws, they are all for special situations like lost the screw accidently, the staff break the screws accidently etc.
Don’t worry about whether the installation is incomplete, as long as you install all the scews based on the actual installation quantity.

Step 3

Loosen handle screw, insert handle, tighten hand screw.
L-shaped wrench 4mm

Step 4

Press the handle down, loosen main engine lock, make the blade up.

 If you found spare screws, they are all for special situations like lost the screw accidently, the staff break the screws accidently etc.
Don’t worry about whether the installation is incomplete, as long as you install all the scews based on the actual installation quantity.

Step 5

Install panel screws, tighten them.

Notice:

L-shaped wrench 2.5mm

Model|

Actual panel screws
need to install

---|---
KC240| 3pcs
KC340| 4pcs
KC460| 5pcs
KC660| 7pcs

Step 6

Tighten main engine screws.
Use L-shaped wrench 4mm

Straight Cutting

Insert material between the cutting blade and the base, flush it with the guide bar as shown and hold the material then push handle down to complete a cut.

Warning: Maintain control of the handle. Do not allow handle to slam back after making a cut.

Angle Cutting

Insert material between the cutting blade and the base, material aligned at corresponding angles, then push the handle down to complete a cut.

Warning: Maintain control of the handle. Do not allow handle to slam back after making a cut.

Changing the Blade

Use the L-shaped wrench 4mm to remove the screws, then hold the bald by each end and carefully move the blade out of blade holder.

Note: The flat side of the blade facing the table.

Warning: Do not put your fingers against the sharp edge of the blade at any time.

Carry

First secure the handle with the lock when not in use and carry the cutter as shown. Small wheels make moving easily.

Product parameters

Maximum cutting thickness

|

14mm

Longitudinal cutting throat diameter| 138mm| 210mm| 317mm| 458mm
Blade size| 9in| 13in| 18in| 26in

Packing list

Main en gin e————————————1 PC
Pane l———————————————-1 PC
Hand I e——————————————–1 PC
User man u a 1————————————-1 PC
Spare parts packing—————————- 1 SET

Customer Support

Installation Video KC240/340
Installation Video KC460/660
Email:nl@nlbfou.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>