MONOGRAM ZIC363IPVLH 36 Premium Integrated Bottom-Freezer Refrigerator User Manual

: June 15, 2024
: MONOGRAM

Table of Contents

MONOGRAM ZIC363IPVLH 36 Premium Integrated Bottom-Freezer Refrigerator
Product Information
Product Usage Instructions
Bracket D1 Installation
Bracket G1 (Right) Installation
Bracket G1 (Left) Installation:

MONOGRAM ZIC363IPVLH 36 Premium Integrated Bottom-Freezer Refrigerator

Product Information

Specifications:

Model: Unknown
Rev. 0 6-23 GEA

Product Usage Instructions

Bracket A1 Installation:

Place the provided template on the back of the panel.
Align the top dashed line of the template with the top edge of the panel.
Align the right dashed line of the template with the right edge of the panel.
Drill two pilot holes as indicated on the template.
Remove the template and install the bracket, ensuring it is centered on the screws. Do not tighten the screws yet.
Drill a pilot hole in the center of the empty slot in the bracket and install a screw.

*PILOT HOLES TO BE 5/64″ AND NOT EXCEED 1/2″ DEEP.

PRINT TEMPLATE ON 8.5″ X 11″ (21.59 CM X 27.94 CM) PAPER ONLY.
PRINT ACTUAL SIZE (100% SCALE). DO NOT SCALE TO FIT.
NO MARGINS OR HEADERS/FOOTERS.
VERIFY LINE MEASURES 6″ (15.24 CM) LONG BEFORE DRILLING PILOT HOLES.

Bracket D1 Installation

Place the provided template on the back of the panel.
Align the top dashed line of the template with the top edge of the panel.
Align the left dashed line of the template with the left edge of the panel.
Drill two pilot holes as indicated on the template.
Remove the template and install the bracket, ensuring it is centered on the screws. Do not tighten the screws yet.
Drill a pilot hole in the center of the empty slot in the bracket and install a screw.

PILOT HOLES TO BE 5/64″ AND NOT EXCEED 1/2″ DEEP.

Bracket G1 (Right) Installation

Measure the distance from the top edge to the bottom edge of the panel and mark the center along the right edge of the panel.
Place the provided template on the back of the panel.
Point the top edge of the template towards the top edge of the panel.
Align the centerline of the template with the center of the panel.
Align the right dashed line of the template with the right edge of the panel.
Drill pilot holes as indicated on the template.
Remove the template and install the bracket after mounting the panel to the door.

PILOT HOLES TO BE 5/64″ AND NOT EXCEED 1/2″ DEEP.

PRINT TEMPLATE ON 8.5″ X 11″ (21.59 CM X 27.94 CM) PAPER ONLY.
PRINT ACTUAL SIZE (100% SCALE). DO NOT SCALE TO FIT.
NO MARGINS OR HEADERS/FOOTERS.
VERIFY LINE MEASURES 6″ (15.24 CM) LONG BEFORE DRILLING PILOT HOLES.

Bracket G1 (Left) Installation:

Measure the distance from the top edge to the bottom edge of the panel and mark the center along the left edge of the panel.
Place the provided template on the back of the panel.
Point the top edge of the template towards the top edge of the panel.
Align the centerline of the template with the center of the panel.
Align the left dashed line of the template with the left edge of the panel.
Drill pilot holes as indicated on the template.
Remove the template and install the bracket after mounting the panel to the door.

PILOT HOLES TO BE 5/64″ AND NOT EXCEED 1/2″ DEEP.

Bracket B1 Installation

Place the provided template on the back of the panel.
Align the bottom dashed line of the template with the bottom edge of the panel.
Align the right dashed line of the template with the right edge of the panel.
Drill pilot holes as indicated on the template.
Remove the template and install the bracket. Do not tighten the screws yet.

PILOT HOLES TO BE 5/64″ AND NOT EXCEED 1/2″ DEEP.

PRINT TEMPLATE ON 8.5″ X 11″ (21.59 CM X 27.94 CM) PAPER ONLY.
PRINT ACTUAL SIZE (100% SCALE). DO NOT SCALE TO FIT.
NO MARGINS OR HEADERS/FOOTERS.
VERIFY LINE MEASURES 6″ (15.24 CM) LONG BEFORE DRILLING PILOT HOLES.

BRACKET E1:

PLACE TEMPLATE ON PANEL BACK.
ALIGN BOTTOM DASHED LINE TO PANEL BOTTOM EDGE.
ALIGN LEFT DASHED LINE TO PANEL LEFT EDGE.
DRILL PILOT HOLES* IDENTIFIED BELOW.
REMOVE TEMPLATE AND INSTALL BRACKET. DO NOT TIGHTEN SCREWS.

PILOT HOLES TO BE 5/64″ AND NOT EXCEED 1/2″ DEEP.

BRACKET C1:

PLACE TEMPLATE ON PANEL BACK.
ALIGN TOP DASHED LINE TO PANEL TOP EDGE.
ALIGN RIGHT DASHED LINE TO PANEL RIGHT EDGE.
DRILL PILOT HOLES* IDENTIFIED BELOW.
REMOVE TEMPLATE AND INSTALL BRACKET. DO NOT TIGHTEN SCREWS.

PILOT HOLES TO BE 5/64″ AND NOT EXCEED 1/2″ DEEP.

PRINT TEMPLATE ON 8.5″ X 11″ (21.59 CM X 27.94 CM) PAPER ONLY.
PRINT ACTUAL SIZE (100% SCALE). DO NOT SCALE TO FIT.
NO MARGINS OR HEADERS/FOOTERS.
VERIFY LINE MEASURES 6″ (15.24 CM) LONG BEFORE DRILLING PILOT HOLES.

BRACKET F1:

PLACE TEMPLATE ON PANEL BACK.
ALIGN TOP DASHED LINE TO PANEL TOP EDGE.
ALIGN LEFT DASHED LINE TO PANEL LEFT EDGE.
DRILL PILOT HOLES* IDENTIFIED BELOW.
REMOVE TEMPLATE AND INSTALL BRACKET. DO NOT TIGHTEN SCREWS.

PILOT HOLES TO BE 5/64″ AND NOT EXCEED 1/2″ DEEP.

BRACKET A1:

PLACE TEMPLATE ON PANEL BACK.
ALIGN TOP DASHED LINE TO PANEL TOP EDGE.
ALIGN RIGHT DASHED LINE TO PANEL RIGHT EDGE.
DRILL PILOT HOLES* IDENTIFIED BELOW.
REMOVE TEMPLATE AND INSTALL BRACKET. DO NOT TIGHTEN SCREWS.

PILOT HOLES TO BE 5/64″ AND NOT EXCEED 1/2″ DEEP.

PRINT TEMPLATE ON 8.5″ X 11″ (21.59 CM X 27.94 CM) PAPER ONLY.
PRINT ACTUAL SIZE (100% SCALE). DO NOT SCALE TO FIT.
NO MARGINS OR HEADERS/FOOTERS.
VERIFY LINE MEASURES 6″ (15.24 CM) LONG BEFORE DRILLING PILOT HOLES.

BRACKET D1:

PLACE TEMPLATE ON PANEL BACK.
ALIGN TOP DASHED LINE TO PANEL TOP EDGE.
ALIGN LEFT DASHED LINE TO PANEL LEFT EDGE.
DRILL PILOT HOLES* IDENTIFIED BELOW.
REMOVE TEMPLATE AND INSTALL BRACKET. DO NOT TIGHTEN SCREWS.

PILOT HOLES TO BE 5/64″ AND NOT EXCEED 1/2″ DEEP.

BRACKET B1:

PLACE TEMPLATE ON PANEL BACK.
ALIGN BOTTOM DASHED LINE TO PANEL BOTTOM EDGE.
ALIGN RIGHT DASHED LINE TO PANEL RIGHT EDGE.
DRILL TWO PILOT HOLES* IDENTIFIED BELOW.
REMOVE TEMPLATE AND INSTALL BRACKET, CENTERED ON SCREWS. DO NOT TIGHTEN SCREWS.
DRILL PILOT HOLE* IN CENTER OF EMPTY SLOT IN BRACKET AND INSTALL SCREW.

PILOT HOLES TO BE 5/64″ AND NOT EXCEED 1/2″ DEEP.

PRINT TEMPLATE ON 8.5″ X 11″ (21.59 CM X 27.94 CM) PAPER ONLY.
PRINT ACTUAL SIZE (100% SCALE). DO NOT SCALE TO FIT.
NO MARGINS OR HEADERS/FOOTERS.
VERIFY LINE MEASURES 6″ (15.24 CM) LONG BEFORE DRILLING PILOT HOLES.

BRACKET E1:

PLACE TEMPLATE ON PANEL BACK.
ALIGN BOTTOM DASHED LINE TO PANEL BOTTOM EDGE.
ALIGN LEFT DASHED LINE TO PANEL LEFT EDGE.
DRILL TWO PILOT HOLES* IDENTIFIED BELOW.
REMOVE TEMPLATE AND INSTALL BRACKET, CENTERED ON SCREWS. DO NOT TIGHTEN SCREWS.
DRILL PILOT HOLE* IN CENTER OF EMPTY SLOT IN BRACKET AND INSTALL SCREW.

PILOT HOLES TO BE 5/64″ AND NOT EXCEED 1/2″ DEEP.

FAQ

Q: What size should the pilot holes be?
A: The pilot holes should be 5/64 in size and not exceed 1/2 inch in depth.
Q: What paper size should I use for printing the templates?
A: Print the templates on 8.5 x 11 (21.59 cm x 27.94 cm) paper only.
Q: How should I print the templates?
A: Print the templates at actual size (100% scale) without scaling to fit. Ensure there are no margins or headers/footers. Verify that the line measures 6 inches (15.24 cm) long before drilling pilot holes.