SimpliFire SF-FM43-WH Floating Mantel Wall Mount Linear Electric Instruction Manual
- June 15, 2024
- SimpliFire
Table of Contents
SimpliFire SF-FM43-WH Floating Mantel Wall Mount Linear Electric
kit component
Preparation
Remove the mantel and hardware from the packaging.
Refinishing (Optional)
Mantel is finished in white. If refinishing is desired, the following steps are recommended prior to assembling the mantel:
- Properly cover any areas of workspace that you do not want to be painted.
- Lightly scuff the existing finish with 320 grit sandpa-per.
- remove dust using lint-free cloth.
- For best results, apply a base coat of spray paint primer to evenly cover the mantel.
- Wait the recommended amount of time per the paint and primer instructions, then apply a spray paint top coat in the color of choice to evenly cover the mantel.
- Apply additional top coats until desired coverage is achieved
Tools and Supplies Needed
Magnetic Phillips screwdriver
NOTICE:
- Follow all recommended guidelines for the materials you are using.
- Do not spray paint near the appliance.
- Do not spray paint while the appliance is operating.
- Always wear appropriate gloves, eye protection, clothing, and a respirator or mask when painting.
- The room or area you are spraying must be well ventilated and must be properly masked to prevent overspray from covering woodwork, floors or funishings.
Mantel Options
There are three available mantels.
SF-FM43-WH Installation
- Slide the bottom mantel section onto the appliance and connect the bottom mantel wire connection to the appliance wire connector protruding from the bottom of the appliance (the cover plate on the bottom of the appliance may need to be removed to access the wire connector). See Figures 1 and 2.
- Fasten the bottom mantel section to the appliance with two M5*35 Phillips screws. See Figure 5.
- Before installing the top mantel, bend the mounting tabs slightly into a more open position to allow for clearance while installing the mantel. See Figure 3.
- Slide the top mantel section onto the appliance See Figure 4.
- Once the top mantel is in place, bend the mounting tabs at a 90° angle so it is flush against the inner surface of the appliance.
- Secure the top mantel to the appliance using two (2) M5X12 thumb screws with rubber washers. See Figure 5.
SF-FM50-WH and SF-FM60-WH Installation
- Slide the bottom mantel section onto the appliance and connect the bottom mantel wire connection to the appliance wire connector protruding from the bottom of the appliance (the cover plate on the bottom of the appliance may need to be removed to access the wire connector). See Figure 6.
- Fasten the bottom mantel section to the appliance with two M5*35 Phillips screws. See Figure 10.
- Attach the side panel wire connector to the connector on the bottom mantel section. Slide the side panels into the recess between the bottom mantel section and the wall. Take care not to pinch the wire between the side panel and the wall. See Figure 7.
- Before installing the top mantel, bend the mounting tabs slightly into a more open position to allow for clearance while installing the mantel. See Figure 8.
- Slide the top mantel section onto the appliance. See Figure 9.
- Once the top mantel is in place, bend the the mounting tabs at a 90° angle so it is flush against the inner surface of the appliance.
- Secure the top mantel to the appliance using two (2) M5X12 thumb screws with rubber washers. See Figure 10.
- Secure the side panels using two (2) provided M5*35 screws.
SimpliFire, a brand of Hearth & Home Technologies 7571 215th Street West, Lakeville, MN 55044 www.hearthnhome.com
NOTICE! DO NOT discard this manual. Important service and maintenance instructions are included. Once the appliance is mounted to the wall and the preferred electrical connection ha been installed, the mantel can be installed.
Scan for easy 3D instructions
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>