Warm Y SY-618 Portable Electric Kettle User Manual
- June 15, 2024
- Warm Y
Table of Contents
Warm Y SY-618 Portable Electric Kettle
Thank you for buying our kettle! Please read the instructions carefully before using the kettle! And keep it properly for reference when necessary!
Kettle Description & Parts
Product Name| Type| Capacity| Rated Watts| Rated Voltage| Rated Frequency|
Complied Standard
---|---|---|---|---|---|---
Liquid Heater (Electric Water Heater)
|
SY-616 SY-617 SY-618A
|
380ml
|
300W
|
HOV~
|
50Hz
|
GB 4706.1-2005
GB 4706.19-2008
- Products vary in appearance, the pictures above are for reference only. All products are subject to the actual ones.
- New updates on the products are subject to be shown in the latest manual, without prior notice.
Operating Instructions
Before Use
- Remove the cover, add water and make sure water is within the max level. When water is boiled, empty the kettle and clean the pot with clean water. For a better cleaning, please repeat the whole process.
- Make sure water is below the maximum level of the pot or it may spill out of the kettle when boiled.
- If the kettle is powered on without water in the pot, its service life will be reduced.
- Switch on, the buzzer ticks, the kettle is ready to use when the indicator display lights up for a second and displays.
- Touch the “TOUCH SWITCH’ button: first press, it shows 212°F, second press, it shows 195°F, third press, it shows 175°F, and fourth press, it shows 140°F.
- When the temperature is set, the figure will flash 3 times, and the kettle will start to heat water.
- The temperature rises to the set one, the buzzer will tick 3 times, and the kettle starts automatic insulation (The actual temperature will be displayed), the temperature canbe maintained for 12 hours.
- If continuous heating or reheating is needed, switch on when the kettle cools down.
- The unit is designed for water draining and steam venting The kettle can be covered when heating water. Remove the cover when stewing, or the vent holes on the cover will be obstructed
IMPORTANT SAFEGUARDS
Warning
Please read the following instructions carefully before you use them to avoid
any injuries or damages.
- Never immerse the unit in water or other liquids.
- Keep close eyes when the kettle is used near a child
- The kettle is not intended to be used by persons with mental disabilities or children
- Do not leave the kettle running without close supervision
- Unplug the power cord before cleaning
- Leave the kettle cool before cleaning or storing
- When any part is damaged directly return the kettle to the service center for inspection and maintenance.
- Keep the kettle away from the electric stove or microwave.
- Leave it on a flat surface
- Do not heat other stuff than water
- Do not overfill the kettle or boiled water may spill out.
- Do not switch the kettle on without water inside.
- Make sure the kettle is on a flat surface when water is filled
- Power cord replacement must be conducted by the manufacturer or the service center
- Plug the cord into an outlet. Switch on the kettle. The power indicator lights up. The kettle starts to heat
- When not in use, switch off, and unplug the power cord.
CLEANING & CARE
Always turn the kettle off and remove the plug from the outlet before cleaning!
IMPORTANT SAFEGUARDS
- Switch the kettle off and remove the plug from the outlet before cleaning. Wipe the kettle body with a damp mop.
- When scale is spotted use vinegar to dissolve it. Put 1 teaspoon of vinegar and 2 teaspoons of water into the kettle.
- Switch on the power. Boil the vinegar and water. Leave it cool. Unplug and rinse several times with clean water. The removal of built-up scale from the inner pot will help extend the life of the kettle.
- Empty the kettle after each use and put it in a cool place, keeping away from sunshine.
CIRCUIT DIAGRAM
For reference only, subject to change without prior notice!
Food grade material
| Components | Material | Testing Results |
|---|---|---|
| Stainless Steel Inner Pot NTC Stainless Steel Case | Stainless Steel | |
| 06Cr19Ni10(304) | Compliance with the standard Requirements | |
| Cover | PP(polypropylene) | Compliance with the standard Requirements |
| NTC seal ring | PDMS (Silica gel ) | Compliance with the standard Requirements |
Notice
- The components and materials used for different types of kettles may vary, all are subject to the actual products.
- Please keep the stainless steel parts away from the acid stuff
Environmental Protection Material
The information listed in the table below is based on the requirements of
SJ/T113664 and GB/T 26572. All the information listed in the table is based on
the regulations of SJ/T 11364.
O: means the amount of the hazardous material contained in the associated
part is below the max limit specified in the requirements of GB/T 26572.
Product Name: Warm Y Electric kettle
Components
| Hazardous materials
pb
|
Hg
|
Cd
|
(Cr (VI))
|
(PBB)
|
(PBDE)
Plastic Parts| 0| 0| 0| 0| 0| 0
Circuit Board| X| 0| 0| 0| 0| 0
Heating Unit| 0| 0| 0| 0| 0| 0
Hardware| 0| 0| 0| 0| 0| 0
Power Cord| 0| 0| 0| 0| 0| 0
Temperature Sensor| X| 0| 0| 0| 0| 0
Screw| 0| 0| 0| 0| 0| 0
Packing Material| 0| 0| 0| 0| 0| 0
X: means the amount of the hazardous material contained in the associated part is above the max limit specified in the requirements of GB/T 26572 due to the restriction of the current technology, and should be improved when the new technology is available.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>