FRANKE 792-10-12 Cooker Hood Instruction Manual

FRANKE 792-10-12 Cooker Hood

Product Information

• Specifications
  • Model Number: 991.0695.253/D000000009083/180656/2023-02-17
  • Electrical Connection: 230 V ~ with grounding
  • Lighting: LED 4 x 2 W
• Installation
  • The cooker hood is intended for free-hanging installation. It comes with a motorized damper, LED lamps, and a metal mesh filter.
• Electrical Installation
  • Before starting the installation, make sure the electrical connection is properly done. Connect the cooker hood to a 230 V ~ power source with proper grounding.
• Measurements
  • Refer to Fig. 1 for the installation measurements:
  • Maximum Connection Output for Control Cable: 900 W at 230 V
  • Lighting: LED 4 x 2 W
• Fixing Parts
  • All necessary fixing parts, screws for mounting, etc., are supplied with the cooker hood.
• Installation Instructions
  • Mark out the ceiling before installation. Use Fig. 3 as a guide.
  • Protect the stove top with a piece of cardboard from the packaging (Fig. 4).
  • Place the cooker hood on the stove top, ensuring it is flat and the filter is resting on the surface.
  • Use a plumb line to mark the centre of the cooker hood on the ceiling.
  • Locate the centre of the drill template (supplied) against the marking on the ceiling, ensuring the cooker hood ends up in the intended position.
  • Turn the drill template so that the arrow points in the same direction as the front of the cooker hood.
  • Check that the duct connection and electrical connection can still be made once power is installed in the ceiling.
  • Adjust the frame height according to your requirements.
  • Install chimney drums onto the frame using screws (Fig. 6A).
  • Adjust the length of the hose/duct for connection to the outlet air duct (Fig. 5B).
• FAQ
  • Q: What is the electrical connection requirement for this cooker hood?
  • A: The cooker hood requires a 230 V ~ electrical connection with grounding.
  • Q: What is the maximum connection output for the control cable?
  • A: The maximum connection output for the control cable is 900 W at 230 V.
  • Q: How many LED lamps are included in this cooker hood?
  • A: This cooker hood comes with 4 LED lamps, each with a power of 2 W.

SAFETY INSTRUCTIONS

• Please read this installation and user guide carefully before installing and using the product, paying special attention to the safety instructions.
• Save these instructions for later use or for the party who may take over the product after you.
• Disconnect the product from the power supply before cleaning or maintenance.
• Diversion of exhaust air must be carried out per instructions issued by the appropriate authority.
• Exhaust air may not be directed into flues that are used for fumes from items such as gas, wood or oil-burning stoves or fireplaces.
• The distance between the stove/ gas hob and the product must be at least 65 cm. Adjust accordingly if the gas hobs manufacturer recommends a higher mounting height.
• For safety reasons, installation and replacement of cables or other types of connectors should only be carried out by a qualified professional.
• Flambéing underneath the product is not permitted.
• If the product is to be used at the same time as products that use energy sources other than electricity, i.e., gas hobs, gas, wood or oil-burning stoves or fireplaces, etc, the room must have an adequate supply of air.
• The product may be used by children from 8 years of age and persons with mental, sensory or physical impairment, or a lack of experience and knowledge, provided they are given information about how the product is to be used.
• Children should not be allowed to play with the product. Children must not undertake cleaning or maintenance of the product unsupervised.
• Accessible parts of the product may become hot when food is being prepared.
• A fire is more likely to spread if the product is not cleaned as frequently as indicated.

INSTALLATION

The cooker hood is intended for free-hanging installation. The cooker hood has a motorised damper, LED lamps and a metal mesh filter. Installation, use, care, maintenance, etc., are described in these instructions

TECHNICAL INFORMATION

INSTALLATION
Fixing parts, screws for mounting, etc. are supplied with the cooker hood.
Electrical installation

• The cooker hood is supplied with an electrical cable and earthed plug for connection to an earthed wall socket as well as a control cable for connection to an external unit or units.
• Once the control cable is connected, the relay contact is closed when the damper is open (-12). The control cable can be left disconnected if this feature is not required (-10).
• When installing with an extended upper chimney section, take this into account when positioning sockets.
• The junction box or wall socket must be accessible after installation is complete.

Installation Components

Marking out the ceiling before installation Attention!

• For max. total height, distance between the bottom of the cooker hood and the top of the chimney, see dimensions drawing Fig. 1.
• When installing with an extended upper chimney section, see dimensions for this.
• Protect the stove top with a piece of cardboard from the packaging, Fig. 4. Place the cooker hood on the stovetop. Make sure it\ is flat with the filter resting on the surface.

Attention!

• To avoid the risk of head injury, do not allow any part of the product to protrude beyond the front of the stovetop.
• Use a plumb line to mark the centre of the cooker hood on the ceiling. Locate the centre of the drill template supplied, A Fig. 4, against the marking in the ceiling so that the cooker hood ends up in the intended position.

Attention!

• Turn the drill template so that the arrow points in the same direction as the front of the cooker hood.
• Mark out the template screw holes, A, and the connection to the outlet air duct. Drill holes in the centre of all the marked screw holes.
• Check which of the fastening alternatives apply and adapt the holes to fit screws/plugs or nuts, bolts and washers. If the supplied plugs are to be used, drill 6 mm holes. Insert wall plugs D into the holes.
• Check that the screws and plugs used are intended for the ceiling material. Cut out holes for connecting outlet air. Insert and tighten screws C into the pre-drilled holes for the keyhole attachments until they protrude a few mm,Fig. 6.
• Check that the duct connection and electrical connection can still be made once power is installed in the ceiling.

Assembly

Adjusting frame height

• Adjust frame height to ceiling height and cooker hood installation height. Measure the total ceiling height. Deduct cooker height, installation height and the chassis dimensions; see dimensions drawing Fig. 1
  • Frame measurement =
  • Total ceiling height – cooker height – installation height – chassis height.
• When adjusting the height of the frame, remove the screws, (8 pcs) Fig. 5A. Adjust the height of the frame and lock it by screwing in the screws again. It may be necessary to move the screws to other hole positions.
• Adjusting the length of the hose/duct for connection to the outlet air duct Fig. 5B
• Measured the frame’s adjusted length. Deduct the connection box dimensions; see the measurements drawing, Fig. 1.
  • Length of hose/duct =
  • Frame measurement – 235 mm.

Installing chimney drums

• Place the adjusted frame on the floor or on a table that is protected with a piece of cardboard from the packaging. Slide the two drums onto the frame.
• Fasten the outer drum to the frame using screws E, Fig. 6A.

Ceiling installation

• Lift up the frame and slot the key holes over the four screws D Fig. 6, installed in the ceiling/extension section.
• Position the frame and tighten the screws.
• Lock in place using the fifth screw, H Fig. 6.

Attention!

• Turn the frame so that the arrow is on the same side as the front of the cooker hood.

Frame installation

• Remove grease filter Fig. 15. Adapt the length of the connection hose/ duct according to frame height, the ceiling connection and the height of the connection box (235 mm).
• Fit the connection hose/duct to the cooker hood’s outlet air collar.
• Slide the hose/duct, the electrical connection cable and the cooker hood into the frame and fasten the chassis using screws F, Fig. 7A.
• Reinstall the grease filter.
• Connect the hose/duct to the outlet air duct in the ceiling, Fig. 7B.

Connection to exhaust flue

• Connect the cooker hood with a pipe or tubing Ø 160 mm. If the connection is Ø 125 mm, a reducing coupling sleeve must be used.

Attention!

• When using a connecting tubing, the tubing must be stretched and assembled to fit directly next to the connection, Fig. 8.

Installing the upper chimney drum

• Pull the chimney drum into position and attach it using screws E, Fig. 9.

Removal of protective plastic

• Cut the protective plastic in the joint between the upper and lower drum using a sharp knife or razor blade, Fig. 9. Remove the plastic from the chimney.
• Remove all protective plastic from the filter and any other parts of the product.

ADJUSTING THE AIRFLOW

SETTING THE DAMPER

• The airflow is adjusted with the aid of the damper.
• The damper can be accessed for adjustment by removing the filter.

Measurement outlet

• The measurement pressure Pm is measured in the measurement outlet, Fig. 10A. With the aid of the measurement pressure Pm and the position of the damper, the volume of air can be read off in the adjustment diagram, where F1-F6 are forced ventilation and G1-G6 are basic ventilation.
• If the volume of air has to be altered, read off a new damper setting from the diagram and then adjust the position of the damper according to the following description.

Adjusting forced ventilation

Open the damper hatch, Fig. 11B.
Attention!
Handle the damper with care!

Remove the forcing hatch, Fig. 12C, by lifting it from the locking tags, Fig. 12D.

Attention!

• Handle the forcing hatch with care, making sure it is not bent.
• Move the hatch to the desired position.
• Markings for the position of the forcing hatch, F1–F6, correspond to the values in the ‘Forced ventilation’ diagram, see Fig. 17 page 48.
• Press the forcing hatch into the lock, ensuring that it is properly secured.
• Measure the pressure Pm and check that the desired forcing flow is achieved. (See diagram, Fig. 17 page 48.)

Adjusting basic ventilation

• Adjust the basic ventilation with the damper hatch closed. Undo the screws, Fig. 13E.
• Move the damper hatch, Fig. 13F, to the desired position.

Attention! Handle the damper carefully.

• The markings for the position of the damper hatch, G1–G6, correspond to the values in the ‘Basic ventilation’ diagram, see Fig. 18 page 49.
• Lock the damper hatch in place with the screws, Fig. 13E.
• Measure the pressure Pm and check that the desired basic flow is achieved. (See diagram, Fig. 18)

INSTRUCTIONS FOR USE

FUNCTION SWITCH

• A. Lighting.
• B. Damper function. Press once to open the damper. The indicator lamp comes on when the damper is open.
• C. Indicator lamp
  • The damper closes automatically after 60 minutes or by pressing button B once more.
  • It is a good idea to open the damper a short while before and after cooking, to avoid the spread of odours in the room.

CARE AND MAINTENANCE

Attention!
To ensure operation, quality and safety after servicing and maintenance, use only original parts.
Cleaning
The cooker hood should be cleaned with a damp cloth and washing-up liquid. With normal usage, the filters must be cleaned at least every other month. Clean more often after intensive use.

Remove the grease filters by opening the snap retainer, Fig. 15 Handle the filters carefully, taking care not to bend them. Soak the filter in a solution of warm water and washing-up liquid. The filter can also be washed in a dishwasher. Refit the grease filters after cleaning, making sure they snap firmly into place. The inside of the cooker hood and the damper must be cleaned at least twice a year. Wipe with a damp cloth and washing-up liquid. The damper is easiest to clean when it is open.

REPLACEMENT OF LED LIGHTING AND LED DRIVER

Attention!

• The replacement of the LED lighting and LED driver must be carried out by an authorized professional. Contact the service organization.
• The lighting and driver must be replaced with an equivalent special light fixture and driver from the manufacturer or its service agent.

SERVICING AND WARRANTY

Check that the fuse is intact. Go through all the functions to check what is not working.
Contact Franke Service

• Tel. +46 (0)912-40 500
• www.franke.se/service.
• They can help you fix the problem or refer you to the nearest service agent for fast and effective service.
• The product is covered by the relevant APPLiA provisions.

PACKAGING AND PRODUCT RECYCLING

• The packaging should be deposited at your nearest recycling point.

The symbol means that the product must not be treated as household waste. It should instead be taken to a collection point for the recycling of electrical and electronic components. By ensuring that the product is dealt with perfectly, you are helping to prevent the adverse environmental and health effects that could arise if the product was disposed of as regular waste. For further information on recycling, contact your local authority or waste disposal service, or the store where you purchased your product. 991.0695.253/D000000009083/180656/2023-02-17

FORCERET VENTILATION

• Indreguleringsdiagram

GRUNDVENTILATION

• Indreguleringsdiagram

FORCERET VENTILATION

• Dimensioneringsdiagram

GRUNDVENTILATION

• Dimensioneringsdiagram

References

• Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>