ToLife N2 PERSONAL CERAMIC HEATER OPERATING MANUAL
- December 24, 2023
- ToLife
Table of Contents
ToLife N2 PERSONAL CERAMIC HEATER
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE
PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY
INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL
INJURY AND/OR PROPERTY DAMAGE!
Have a Question? Need a Part?
Please Do Not Return the Product to the Store!
Contact Lasko Customer Service: 1-800-233-0268 Monday-Friday 8 AM – 5 PM EST.
IMPORTANT SAFETY INFORMATION
WARNING
When using electrical appliances, these instructions and warnings should always be followed to reduce the risk of fire, electrical shock and injury to persons:
Read all instructions before using this Heater.
- ALWAYS PLUG HEATERS DIRECTLY INTO A WALL OUTLET/RECEPTACLE. NEVER USE WITH AN EXTENSION CORD. DO NOT PLUG THE HEATER INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MULTIPLE OUTLET ADAPTER, CORD REEL OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE HAZARD. PLUG UNIT DIRECTLY INTO A 120V WALL OUTLET ONLY.
- FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT HEATER PLUG FITS TIGHTLY INTO THE OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS NOT OVERHEATING. IF NECESSARY HAVE A QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET. DO NOT USE THIS HEATER WITH ANY SOLID-STATE SPEED CONTROL DEVICES.
- Make certain that the power source conforms to the electrical requirements of the Heater.
- Extreme caution is necessary when any Heater is used by or near children or invalids. The Heater should not be left operating unattended. Never leave children unattended when the heater is on or plugged in.
- This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
- DO NOT use the Heater in areas where gasoline, paint, or flammable liquids are used or stored. DO NOT use Heater in locations where flammable or explosive chemicals are stored, or in wet atmospheres.
- Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any manner. To disconnect Heater, turn the Heater OFF then remove the plug from the outlet.
- Always unplug the Heater when not in use. Unplug the power cord before servicing or moving the Heater.
- Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire, or damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation.
- Do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings may become blocked. Do not depend on the on/off switch as the sole means of disconnecting power when servicing or moving the heater. Always unplug the power cord.
CAUTION
- Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power Cord so the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with throw rugs, runners, or similar coverings as this may cause cord to overheat. Arrange Power Cord away from room traffic and where it will not be tripped over.
- This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the Heater and keep them at least 1 foot (0.3 m) from the sides and rear.
- This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER locate a Heater where it may fall into a bathtub or other water container.
- DO NOT use Heater outdoors.
- This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for Agricultural Buildings. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
- This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical requirements for Hazardous locations. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008).
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The user is cautioned that changes and modifications made to the equipment
without the approval of the manufacturer could void the user’s authority to
operate this equipment.
Please contact Customer Service at 800-233-0268 Monday through Friday from 8am
to 5pm EST for assistance.
OPERATION (Figure 1)
-
Carefully remove the Heater from the bag and the carton.
Plastic or rubber tabs, like the feet on this unit, may stick to furniture surfaces and/or hardwood floors. The unit may leave a residue that could darken, stain or leave permanent blemishes on the finish of certain furniture surfaces, including wood surfaces, and/or hardwood floors. -
Place the Heater on a firm, level surface.
-
Make certain the Heater Power Knob is in the OFF position before plugging unit into an outlet.
-
Plug the cord set into a 120 volt outlet. Be sure that the plug fits tightly into outlet. When plugs fit loosely into receptacles, they may slip partially or completely out of the receptacle with only the slight movement of the attached cord. Receptacles in this condition may overheat and pose a serious fire hazard; if covered by a curtain or drape, the fire hazard is even greater.
-
To turn the Heater on push the Power button to the On (I) position. The red light will remain lit while the Heater is on. (Figure 1)
-
To turn the Heater off, push the Power button to the Off (0) position (the red light on display will turn off) and unplug the Heater from the electrical outlet. (Figure 1).
SAFETY FEATURE
- A thermal overload protector is built in to prevent overheating.
- If an overheating temperature is reached, the Heater will automatically shut off. It can only resume operation when the unit is reset.
To Reset Heater:
- Unplug the Heater and wait 10 minutes for the unit to cool down.
- After 10 minutes, plug the Heater in again and follow the OPERATION INSTRUCTION described in this instruction manual.
TROUBLESHOOTING TIPS
If your heater shuts off unexpectedly or fails to operate, the above-mentioned safety feature may have been activated to prevent overheating.
- Be sure the power cord is plugged into a working electrical outlet.
- If your Heater runs for several minutes and shuts off repeatedly, your Heater may require cleaning.
See the Maintenance section below.
If you have a problem that can not be resolved by the steps listed above, contact Technical Assistance at 1-800-233-0268, Monday through Friday, between the hours of 8am and 5pm EST.
MAINTENANCE
To reduce the risk of electrical shock and fire please observe the following
instructions.
Cleaning the Heater regularly will help to maintain its efficiency.
- Always unplug the cord before moving, servicing or cleaning.
- NEVER place the Heater in or near water. DO NOT IMMERSE HEATER IN WATER.
- Clean the Heater only with a vacuum equipped with a brush attachment; the vacuum will remove the lint and dirt from the surface of the Heater.
- Vacuum intake grills every two weeks; this will help to maintain the optimum Heater performance.
- Use a toothbrush or other soft bristle brush to gently loosen any dirt not removed by the vacuum.
- NEVER attempt to take apart the Heater.
- Clean the body of the Heater with a soft cloth only.
- NEVER use ALCOHOL or SOLVENTS such as gasoline, benzene, paint thinner, or other harsh cleaners.
SERVICING: For servicing, other than general user maintenance, please
contact Customer Service at 800-233-0268, Monday through Friday, from 8am-5pm
Eastern.
STORAGE: Store the Heater with these instructions in the original carton
in a cool, dry place.
LIMITED WARRANTY
LASKO PRODUCTS, INC. LIMITED WARRANTY (VALID IN THE USA, ITS TERRITORIES, AND CANADA ONLY)
- WHAT THIS WARRANTY COVERS: This product is warranted against defects in workmanship and/or materials.
- HOW LONG THIS WARRANTY LASTS: This warranty extends only to the original purchaser of the product and lasts for three (3) years from the date of original purchase or until the original purchaser of the product sells or transfers the product, whichever first occurs.
- WHAT LASKO WILL DO: Lasko will, at its sole option, repair or replace any part or parts that prove to be defective or replace the whole product with the same or comparable model. For all warranty claims, the product must be returned to Lasko Products, Inc. at customer expense with proof of purchase within the warranty period. Contact the Lasko customer service department to obtain a Return Authorization (“RA”). DO NOT return products without an RA or the warranty claim will not be processed.
- WHAT THIS WARRANTY DOES NOT COVER: This warranty does not apply if the product was damaged or failed because of accident, improper handling or operation, shipping damage, abuse, misuse, unauthorized repairs made or attempted, or the use of the product for commercial or nonresidential service. This warranty does not cover shipping costs for the return of products to Lasko for repair or replacement. Lasko will pay return shipping charges from Lasko following warranty repairs or replacement.
ANY AND ALL WARRANTIES, EXPRESSED OR IMPLIED (INCLUDING, WITHOUT LIMITATION,
ANY IMPLIED WARRANTY OF MERCHANTABILITY), LAST THREE YEARS FROM THE DATE OF
ORIGINAL PURCHASE OR UNTIL THE ORIGINAL PURCHASER OF THE PRODUCT SELLS OR
TRANSFERS THE PRODUCT, WHICHEVER FIRST OCCURS AND IN NO EVENT SHALL LASKO’S
LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY INCLUDE (I) INCIDENTAL OR
CONSEQUENTIAL DAMAGES FROM ANY CAUSE WHATSOEVER, OR (II) REPLACMENT OR REPAIR
OF ANY HOUSE FUSES, CIRCUIT BREAKERS OR RECEPTACLES. NOTWITHSTANDING ANYTHING
TO THE CONTRARY, IN NO EVENT SHALL LASKO’S LIABILITY UNDER ANY EXPRESS OR
IMPLIED WARRANTY EXCEED THE PURCHASE PRICE OF THE PRODUCT AND ANY SUCH
LIABILITY SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIOD. Some
states and provinces do not allow limitations on how long an implied warranty
lasts, or the exclusion or limitation of incidental or consequential damages,
so these exclusions or limitations may not apply to you. This warranty gives
you specific legal rights. You may also have other rights which vary from
state to state and province to province.
Proof of purchase is required before a warranty claim will be accepted.
CUSTOMER SERVICE:
Toll-Free (800) 233-0268.
Email:
producthelp@laskoproducts.com
Our Customer Service team is available to assist you with product and service
questions, and replacement parts. They can be reached Monday through Friday,
8am-5pm Eastern. Please have your model number available, as well as the type
and style (located on the underside of your product).
Customer Service Dept., 820 Lincoln Ave., West Chester, PA 19380 (Please do
not send the product to this location)
www.laskoproducts.com
PARTS FOR DISCONTINUED, OBSOLETE, AND CERTAIN OTHER PRODUCTS MAY NOT BE
AVAILABLE. DUE TO SAFETY REASONS, MANY ELECTRONIC COMPONENTS AND MOST HEATER
COMPONENTS ARE NOT AVAILABLE TO CONSUMERS FOR INSTALLATION OR REPLACEMENT.
Manual printed in China
FAQs
How does the ToLife N2 handle thermostat control and temperature settings?
The ToLife N2 typically features an adjustable thermostat, allowing users to set and maintain their preferred room temperature for consistent and efficient heating.
Is the ToLife N2 suitable for use in bedrooms or offices?
Yes, the ToLife N2 Personal Ceramic Heater is designed for use in various indoor spaces, including bedrooms, offices, and small living areas.
Does the ToLife N2 Personal Ceramic Heater come with a remote control for convenience?
Some models of the ToLife N2 may include a remote control, offering users the convenience of adjusting settings from a distance.
What safety features are integrated into the ToLife N2 Personal Ceramic Heater to ensure user safety?
The ToLife N2 includes essential safety features such as overheat protection and a tip-over switch, automatically turning off the heater in case of overheating or tipping.
How does the ToLife N2 Personal Ceramic Heater compare in terms of size and weight to similar heaters?
The dimensions and weight of the ToLife N2 are designed for portability, making it compact and easy to move to different locations within your living space.
What are the available heat settings on the ToLife N2 Personal Ceramic Heater?
The ToLife N2 offers two heat settings, typically 750W and 1500W, allowing users to adjust the heat output based on their comfort and energy-saving preferences.
What type of heating element does the ToLife N2 Personal Ceramic Heater use?
The ToLife N2 Personal Ceramic Heater utilizes a ceramic heating element for efficient and effective heating.
Are there specific safety precautions users should take when using the ToLife N2 Personal Ceramic Heater?
Users should follow safety precautions such as avoiding the use of extension cords, keeping the heater away from water, supervising its use, and ensuring proper ventilation in the room.
What should users do if they have further questions or encounter persistent issues with the ToLife N2 Personal Ceramic Heater?
Users can contact the manufacturer's customer support for assistance, and they should avoid attempting any disassembly or repairs unless they are qualified to do so to prevent hazards and potential warranty avoidance.
How can users troubleshoot common issues with the ToLife N2 Personal Ceramic Heater?
If users encounter issues with the ToLife N2, they should refer to the provided user manual for troubleshooting steps, which may include addressing power problems, overheating, or unusual noises.
What maintenance is required to keep the ToLife N2 Personal Ceramic Heater in good working condition?
Maintenance for the ToLife N2 generally involves cleaning the exterior and periodically checking for dust and debris accumulation inside the heater.
Does the ToLife N2 Personal Ceramic Heater offer a timer function, and how does it work?
Some models of the ToLife N2 may include a timer function, enabling users to program the heater to automatically turn on or off after a specified duration for added convenience and energy savings.
Download This Manual PDF:ToLife N2 PERSONAL CERAMIC HEATER OPERATING MANUAL
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>