lowes A05177 7.1 Inch 1 Light Matte Black and Polished Gold LED Mid Century Vanity Light Bar Instruction Manual
- June 15, 2024
- lowes
Table of Contents
lowes A05177 7.1 Inch 1 Light Matte Black and Polished Gold LED Mid
Century Vanity Light Bar
Product Information
Specifications
- Item Number: A05177
- Maximum Voltage: 120V
- Maximum Wattage: Type B, Max 40W per bulb
Product Usage Instructions
Installation Precautions
- We strongly recommend installation by a licensed electrician.
- Read the instruction manual carefully and save it for future reference.
- Always shut off the electricity before starting any work.
Mounting Surface Preparation
The mounting surface should meet the following requirements:
- Clean, dry, and flat
- Strong enough to support the weight of the lamp
- 1/4 larger than the canopy on all sides
- Any gaps exceeding 3/16 should be corrected
Safety Instructions
- Avoid installation near acidic and alkaline substances that may damage the lamp’s surface.
- When replacing bulbs, turn off or unplug the lamp and wait until it cools down, as bulbs can get hot quickly.
- Use common sense, caution, and care when working with electrical products.
Tools Required
Before starting assembly and installation, prepare the following tools (NOT INCLUDED):
- Ladder
- Philips Head or Flat Blade Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
Parts Included
- (C) Green ground screw (1)
- (D) Mounting plate (1)
- (E) Back plate (1)
- (F) Knob nut (2)
- (G) Socket (1)
- (H) Lampshade (1)
Accessories Enclosed
- (A) Mounting screw (2)
- (B) Plastic wire connector (3)
Assembly & Installation Instructions
- Carefully remove the fixture from the carton and check that all parts and accessories are included.
- Turn off the power before starting the installation.
- Secure the mounting plate (D) to the outlet box with the provided mounting screws (A).
- Connect the wires according to the below chart:
Wires Connection Chart
| Connect Black or Red Supply Wire to: | Connect White Supply Wire to: |
|---|---|
| OUTLET BOX GROUND | OUTLET BOX GROUND |
| FIXTURE GROUND | DIMPLES / GREEN GROUND SCREW |
| Clear, Brown, Gold or Black without tracer | Insulated wire(other than green) |
with copper conductor
Clear, Brown, Gold or Black with tracer| Insulated wire(other than green) with
silver conductor
Twist the wires together with plastic wire connectors (B) until tightly joined, and wrap each connector with approved electrical tape. Ensure that no wire strands are exposed and carefully tuck all wires into the outlet box.
FAQ (Frequently Asked Questions)
Q: Can I install this lamp myself?
A: While it is possible to install the lamp yourself, we strongly
recommend installation by a licensed electrician for safety reasons.
Q: What is the maximum voltage and wattage for this lamp?
A: The maximum voltage is 120V and the maximum wattage is Type B, Max 40W
per bulb.
Q: Can I use this lamp with acidic or alkaline substances nearby?
A: It is advised to keep the lamp away from acidic and alkaline
substances to prevent damage to the lamp’s surface.
Q: Do I need to turn off the lamp before replacing bulbs?
A: Yes, it is important to turn off or unplug the lamp and wait until it
cools down before replacing bulbs, as they can get hot quickly.
Q: Are there any additional safety precautions I should be aware of?
A: The safety instructions provided in the manual are not exhaustive.
Always use common sense, caution, and care when working with any electrical
products.
Item Number: A05177
WARNING (To reduce the risk of fire, electric shock, or personal injury):
-
We suggest installation by a licensed electrician.
-
Please read the instruction carefully and save it as you may need it at a later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
-
Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position. -
Place the wall switch in the “OFF” position.
-
-
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
-
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture
PARTS INCLUDING
ACCESSORIES ENCLOSED:
- (A) Mounting screw (2)
- (B) Plastic wire connector (3)
- (C) Green ground screw (1)
- (D) Mounting plate (1)
- (E) Back plate (1)
- (F) Knob nut (2)
- (G) Socket (1)
- (H) Lampshade (1)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.-
Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position. -
Place the wall switch in the “OFF” position.
-
-
Make assembly
Step A1
Unscrew knob nuts (F) from back plate (E) and mounting plate (D), then set them aside for later installation.
Step A2
Carefully pass the supply wires from the outlet box through mounting plate (D).
Secure mounting plate (D) to the outlet box with mounting screws (A).
Step A3
Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
Connect wires according to the below chart
Twist wires together with plastic wire connectors (B) until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Step A4 Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate (E) to mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.
NOTE: back plate (E) should be snug against the wall with knob nuts (F).
If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate (D):- Unscrew the pre-assembled hex nuts.
- Screw the pre-assembled mounting screws in or out of mounting plate (D).
- When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4.
Step A5
- Install bulb (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
- Carefully screw lampshade (H) to socket (G) as shown in the illustration.
-
Check everything is installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>