ZEBRA ET5X Enterprise Tablet User Guide
- June 4, 2024
- ZEBRA
Table of Contents
- ZEBRA ET5X Enterprise Tablet
- Warranty
- Introduction
- Features
- Installing a micro SIM Card (ET55 Only)
- Install a micro SD Card
- Using the Camera
- Regulatory Information
- RF Exposure Guidelines
- Power Supply
- Batteries
- Radio Frequency Interference Requirements-FCC
- Waste Electrical and Electronic Equipment (WEEE)
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ZEBRA ET5X Enterprise Tablet
Zebra reserves the right to make changes to any product to improve reliability, function, or design. Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Zebra products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Zebra products.
Warranty
For the complete Zebra hardware product warranty statement, go to: http://www.zebra.com/warranty.
Service Information
If you have a problem using the equipment, contact your facility’s Technical
or Systems Support. If there is a problem with the equipment, they will
contact the Zebra Support at: http://www.zebra.com/support. For the latest
version of this guide go to: http://www.zebra.com/support.
Software Support
Zebra wants to ensure that customers have the latest release of entitled
software at the time of product purchase. To confirm that your Zebra device
shipped with the latest release of entitled software, visit:
www.zebra.com/support. Check for the latest
software from Software Downloads > Product Line/Product > Go. If your device
does not have the latest entitled software release as of your product purchase
date, please e-mail a request to Zebra at:
entitlementservices@zebra.com. You
must include the following essential device information with your request:
- Model number
- Serial number
- Proof of purchase
- Title of the software download you are requesting.
If it is determined by Zebra that your device is entitled to the latest software release, you will receive an e-mail containing a link directing you to a Zebra web site to download the appropriate software.
Introduction
The ET5X are Windows® and Android™ based tablets that come in 8” and 10” configurations.
- ET50: WLAN only
- ET55: WLAN and WWAN.
Features
NOTE Windows button only available on Windows tablets
- Ambient Light Sensor – Recognizes the ambient light and adjusts the display brightness (if enabled).
- Front Microphone – Use for voice communications (Windows Tablets only) or audio recordings.
- Front Facing Camera – Use for video conferencing (Windows Tablets only) or capturing images and video.
- Camera Indicator LED – Lights red when the camera is activate. Momentarily lights red when the device boots and shuts down.
- Charging Indicator LED – Indicates charging status.
- OFF – device is not connected to charger.
- ORANGE – device is charging.
- GREEN – device is connected and fully charged.
- RED – charge error.
- Windows Button – Press to launch the Windows Home screen (Windows Tablets only).
- Rear Camera – 8MP auto-focus camera for high resolution images and video.
- Camera LED Flash – Provides illumination for the camera.
- Rear Microphone – Use during video recordings.
- Power Button – Push once to start the ET5X; push it again to enable sleep mode. Push and hold it to shut down the ET5X.
- Volume Key – Push the left side to reduce the volume. Press the right side to increase the volume.
- 3.5 mm Audio Jack – Use to connect to headset with microphone.
- MicroSD Card Slot – Provides storage for microSD Card (up to 2 TB).
- Micro USB Interface (charging only) – Provides for charging the ET5X using USB cable and power supply. On Android devices, provides communication with host computer.
- USB 2.0 Port – Provides input for USB devices.
- Back Cover – Covers the service replaceable battery.
- NFC Antenna Position – Use to read NFC cards and RFID tags.
- Stereo Speakers – Provides audio playback.
- Docking Connector – Interfaces with the cradle.
Installing a micro SIM Card (ET55 Only)
To install a micro SIM card:
-
Press the Power button to turn off the ET55.
-
Lift the notched corner of the battery cover
-
Carefully lift the battery cover off the ET55.
-
On the 8” version, push the two locking tabs up, then pull up on the tab to remove battery. On the 10” version, push the two locking tabs up (1), then, using index fingers, lift the battery up (2).
-
Insert the micro SIM card with contacts facing down.
CAUTION Do not use nano to micro SIM card adapters. Only use micro SIM cards. -
Push the micro SIM card in and ensure that it locks into place. On the 8” WWAN version, after installing the SIM card, insert the SIM retainer. The retainer ensures that the SIM card does not move during operation.
-
Align the SIM retainer with the slots on the device.
-
Push the retainer down and ensure it is in the proper position.
-
Replace the battery. On the 10” version, ensure that the two battery latches engage.
CAUTION Be aware of the orientation of the battery cover. Failure to replace the battery cover properly may damage the battery cover. -
Align the tabs on the underside of the cover with the slot around the battery well. Make sure that the notch on the battery cover is at the bottom left cover of the ET5X.
-
Carefully press down around the edge of the cover. Make sure that the cover is seated properly.
-
Press Power button to turn on the ET55.
Install a micro SD Card
To install a microSD card:
- Open access door.
- Insert microSD card into slot with contacts facing down.
- Press the card in to ensure that it is seated properly.
- Close access door.
Charging the ET5X
Use the Communication and Charging Cradle, Rugged Communication and Charging
Cradle or Charge Only Cradle to charge the ET5X.
NOTE The Charge Only Cradle (CRD-ET5X-1SCG1) and the Communication and Charge Cradle (CRD-ET5X-1SCOM1) come with two inserts; tall insert and short insert. Install the tall insert when using an ET5X without a Rugged Frame and Expansion Back. Install the small insert when using an ET5X with an Expansion Back and without a Rugged Frame. Do not install either insert when using the ET5X with the Rugged Frame. The Rugged Communication and Charge Cradle (CRD- ET5X-1SCOM1R) does not come with inserts. Use with ET5X and Rugged Frame with IO Adapter.
Setup the Charge Only Cradle or Communication Cradle, power supply, PWR- BGA12V50W0WW, DC Line Cord CBL-DC-388A1-01 and country-specific AC line cord, sold separately.
- If using the Communication and Charging Cradle, open the bottom access door and hold it to the back of the tablet.
- Align the ET5X with the alignment pins on the cradle.
- Insert the ET5X into the cradle. Note that the Communication Cradle contains a locking mechanism that locks the ET5X to the cradle.
- The ET5X Charging LED indicates charging.
- To remove the ET5X from the Charge Only cradle, hold the cradle down with one hand and lift the ET5X.
To remove the ET5X from either Communication Cradle, press the release button on the right side of the cradle and lift the ET5X. Use thumb to hold down the cradle. The 8” tablet main battery charges from fully depleted to 90% in approximately 2.5 hours and from fully depleted to 100% in approximately 3.5 hours. The 10” tablet main battery charges from fully depleted to 90% in approximately three hours and from fully depleted to 100% in approximately four hours.
Using the Camera
To take photos or videos:
- Open the Camera application. The Camera Indicator LED lights red.
- Point the ET5X camera at an object.
- Touch the on-screen shutter button to take a photo or record a video
Reading NFC Cards And RFID Tags
The ET5X supports reading NFC cards and RFID tags. The NFC antenna is located
on the back of the device under the NFC logo. With an NFC enabled application
open, bring the NFC card toward the antenna. Depending upon the application,
an audio or visual indication indicates successful reading of the card.
Regulatory Information
This device is approved under Zebra Technologies Corporation.
This guide applies to the following Model Numbers: ET50NE, ET50NT, ET50PE,
ET50PT, ET55AE, ET55AT, ET55BE, ET55BT, ET55EE, ET55ET, ET55GE, ET55GT,
ET55RE, ET55RT, ET55TE and ET55TT. All Zebra devices are designed to be
compliant with rules and regulations in locations they are sold and will be
labeled as required. Local language translations are available at the
following website: http://www.zebra.com/support. Any changes or
modifications to Zebra equipment, not expressly approved by Zebra, could void
the user’s authority to operate the equipment.
CAUTION Only use Zebra approved and UL Listed accessories, battery packs and battery chargers. Do NOT attempt to charge damp/wet mobile computers or batteries. All components must be dry before connecting to an external power source. Declared maximum operating temperature: +50°C.
UL Listed Products with GPS
Underwriters Laboratories Inc. (UL) has not tested the performance or
reliability of the Global Positioning System (GPS) hardware, operating
software or other aspects of this product. UL has only tested for fire, shock
or casualties as outlined in UL’s Standard(s) for Safety for Information
Technology Equipment, UL60950-1. UL Certification does not cover the
performance or reliability of the GPS hardware and GPS operating software. UL
makes no representations, warranties or certifications whatsoever regarding
the performance or reliability of any GPS related functions of this product.
Radio Modules
The device contain approved radio module(s). These module(s) are identified
below.
For models:
- ET55Ax and ET55Bx: Radio card, Type(s): EM7355: Sierra Wireless PCI Express (LTE, HSPA+. GSM/GPRS/EDGE, CDMA).
- ET55Rx and ET55Tx: Radio card, Type(s): ME936: Huawei Wireless module (LTE, HSPA+. GSM/GPRS/EDGE).
- ET55Ex and ET55Gx: Radio card, Type(s): EM7455: Sierra Wireless PCI Express (LTE, HSPA+).
Bluetooth® Wireless Technology
This is an approved Bluetooth product. For more information or to view the End
Product Listing, please visit http://www.bluetooth.org/tpg/listings.cfm.
Wireless Devices Country Approvals
Regulatory markings, subject to certification, are applied to the device
signifying the radio(s) are approved for use in the following countries:
United States, Canada, Australia, and Europe1. Please refer to the Zebra
Declaration of Conformity (DoC) for details of other country markings. This is
available at http://www.zebra.com/doc.
Note1: Europe includes: Austria, Belgium, Bulgaria, Croatia, Czech Republic, Cyprus, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
CAUTION Operation of the device without regulatory approval is illegal.
Country Roaming
This device incorporates the International Roaming feature (IEEE802.11d) which will ensure the product operates on the correct channels for the particular country of use.
Ad-Hoc Operation (2.4 GHz Band)
Ad-Hoc operation is limited to Channels 1-11 (2412 – 2462 MHz).
Wi-Fi Direct/ Hot Spot Mode
Operation is limited to the following channels/bands as supported in the
country of use:
- Channels 1-11 (2412-2462 MHz)
- Channels 36-48 (5150-5250 MHz)
- Channels 149-165 (5745-5825 MHz)
Frequency of Operation FCC and IC 5 GHz Only: Industry Canada Statement:
CAUTION The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-Channel mobile satellite systems. High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices.
Pacemakers
Pacemaker manufacturers recommended that a minimum of 15 cm (6 inches) be
maintained between a handheld wireless device and a pacemaker to avoid
potential interference with the pacemaker. These recommendations are
consistent with independent research and recommendations by Wireless
Technology Research.
Persons with pacemakers:
- Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON.
- Should not carry the device in a breast pocket.
- Should use the ear furthest from the pacemaker to minimize the potential for interference.
- If you have any reason to suspect that interference is taking place, turn OFF your device.
Other Medical Devices
Please consult your physician or the manufacturer of the medical device, to
determine if the operation of your wireless product may interfere with the
medical device
RF Exposure Guidelines
Safety Information
Reducing RF Exposure – Use Properly
Only operate the device in accordance with the instructions supplied.
International
The device complies with internationally recognized standards covering human
exposure to electromagnetic fields from radio devices. For information on
“International” human exposure to electromagnetic fields refer to the Zebra
Declaration of Conformity (DoC) at http://www.zebra.com/doc. For further
information on the safety of RF energy from wireless devices, see
https://www.zebra.com/us/en/about-zebra/company-information/corporate-
responsibility.html located under Corporate Responsibility
Europe
Handheld Devices
This device was tested for typical body-worn operation. Use only Zebra tested
and approved belt-clips, holsters, and similar accessories to ensure EU
Compliance.
US and Canada
Co-located Statement
To comply with FCC RF exposure compliance requirement, the antenna used for
this transmitter must not be co-located or operating in conjunction with any
other transmitter/antenna except those already approved in this filing.
Handheld Devices
This device was tested for typical body-worn operation. Use only Zebra tested
and approved belt-clips, holsters, and similar accessories to ensure FCC
Compliance. The use of third-party belt-clips, holsters, and similar
accessories may not comply with FCC RF exposure compliance requirements, and
should be avoided. To satisfy US and Canadian RF exposure requirements, a
transmitting device must operate with a minimum separation distance of 5 mm or
more from a person’s body.
LED Devices
LED Compliance Statement: Classified as “EXEMPT RISK GROUP” according to IEC
62471:2006 and EN 62471:2008 Pulse duration: 1024 ms
Power Supply
Use ONLY a Zebra approved UL LISTED ITE (IEC/EN 60950-1, LPS) Class 2 power supply with electrical ratings: Output 12.0 VDC, 5.0 A, with maximum ambient temperature of at least 40°C. Use of alternative power supply will invalidate any approvals given to this unit and may be dangerous.
Batteries
Taiwan – Recycling
EPA (Environmental Protection Administration) requires dry battery producing
or importing firms in accordance with Article 15 of the Waste Disposal Act are
required to indicate the recycling marks on the batteries used in sales,
giveaway or promotion. Contact a qualified Taiwanese recycler for proper
battery disposal.
Battery Information
CAUTION Risk of explosion if battery is replaced by an incorrect type. Dispose of batteries according to instructions
Use only approved batteries. Accessories which have battery charging capability are approved for use with the following battery models:
- AMME2360, AMME4606 (3.8 VDC, 5,900 mAh) for the 8″ tablet (ET50NE, ET50PE, ET55AE, ET55BE, ET55EE, ET55GE, ET55RE, ET55TE)
- AMME2415, AMME4607 (3.8 VDC, 8,700 mAh) for the 10″ tablet (ET50NT, ET50PT, ET55AT, ET55BT, ET55ET, ET55GT, ET55RT, ET55TT)
Zebra approved rechargeable battery packs are designed and constructed to the highest standards within the industry. However, there are limitations as to how long a battery can operate or be stored before needing replacement. Many factors affect the actual life cycle of a battery pack such as heat, cold, harsh environmental conditions, and severe drops. When batteries are stored over six months, some irreversible deterioration in overall battery quality may occur. Store batteries at half of full charge in a dry, cool place, removed from the equipment to prevent loss of capacity, rusting of metallic parts, and electrolyte leakage. When storing batteries for one year or longer, the charge level should be verified at least once a year and charged to half of full charge. Replace the battery when a significant loss of run time is detected. Standard warranty period for all Zebra batteries is one year, regardless if the battery was purchased separately or included as part of the mobile computer or bar code scanner. For more information on Zebra batteries, please visit: http://www.zebra.com/batterybasics.
Battery Safety Guidelines
- The area in which the units are charged should be clear of debris and combustible materials or chemicals. Particular care should be taken where the device is charged in a non commercial environment.
- Follow battery usage, storage, and charging guidelines found in the user’s guide.
- Improper battery use may result in a fire, explosion, or other hazard.
- To charge the mobile device battery, the battery and charger temperatures must be between +32°F and +104°F (0ºC and +40°C)
- Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact Zebra support.
- For devices that utilize a USB port as a charging source, the device shall only be connected to products that bear the USB-IF logo or have completed the USB-IF compliance program.
- Do not disassemble or open, crush, bend or deform, puncture, or shred.
- Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat.
- Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.
- Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, or expose to fire, explosion, or other hazard.
- Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer.
- Battery usage by children should be supervised.
- Please follow local regulations to promptly dispose of used re-chargeable batteries.
- Do not dispose of batteries in fire.
- Seek medical advice immediately if a battery has been swallowed.
- In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice.
- If you suspect damage to your equipment or battery, contact Zebra support to arrange for inspection.
Removing the Battery
- Lift the notched corner of the battery cover.
- Carefully lift the battery cover off the ET5X.
- On the 8” version, push the two locking tabs up, then pull up on the tab to remove battery. On the 10” version, push the two locking tabs up (1), then, using index fingers, lift the battery up (2).
Radio Frequency Interference Requirements-FCC
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Radio Frequency Interference Requirements – Canada
CAN ICES-3 (B)/NMB-3(B)
Radio Transmitters
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions: (1) This device may not cause
interference; and (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
For RLAN Devices:
The use of 5 GHz RLAN’s, for use in Canada, have the following restrictions:
Restricted Band 5.60 – 5.65 GHz
Label Marking : The Term ‘IC:’ before the radio certification only signifies that Industry Canada technical specifications were met.
Marking and European Economic Area (EEA)
The use of RLAN’s, for use throughout the EEA, have the following restrictions: 5.15 – 5.35 GHz is restricted to indoor use only
Statement of Compliance
Zebra hereby declares that this radio equipment is in compliance with
Directive 2011/65/EU and 2014/53/EU. The full text of the EU Declaration of
Conformity is available at the following internet address:
http://www.zebra.com/doc.
Australia
Use of 5 GHz RLAN’s in Australia is restricted in the following band 5.50 –
5.65GHz.
Hong Kong
In accordance with HKTA1039, the band 5.15GHz – 5.35GHz is for indoor
operation only.
Waste Electrical and Electronic Equipment (WEEE)
For EU Customers : All products at the end of their life must be returned to Zebra for recycling. For information on how to return product, please go to: http://www.zebra.com/weee.
End User License Agreement
IMPORTANT PLEASE READ CAREFULLY : This End User License Agreement
(“EULA”) is a legal agreement between you (either an individual or a single
entity) (“Licensee”) and Zebra International Holdings Corporation (“Zebra”)
for software, owned by Zebra and its affiliated companies and its third party
suppliers and licensors, that accompanies this EULA, which includes machine-
readable instructions used by a processor to perform specific operations other
than machine-readable instructions used for the sole purpose of booting
hardware during a startup sequence (“Software”). BY USING THE SOFTWARE, YOU
ACKNOWLEDGE ACCEPTANCE OF THE TERMS OF THIS EULA. IF YOU DO NOT ACCEPT THESE
TERMS, DO NOT USE THE SOFTWARE.
-
GRANT OF LICENSE. Zebra grants you, End-User Customer, the following rights provided that you comply with all terms and conditions of this EULA: For Software associated with Zebra hardware, Zebra hereby grants you a limited, personal, non-exclusive license during the term of this Agreement to use the Software solely and exclusively for your internal use in support of the operation of your associated Zebra hardware and for no other purpose. To the extent that any portion of the Software is provided to you in a manner that is designed to be installed by you, you may install one copy of the installable Software on one hard disk or other device storage for one printer, computer, workstation, terminal, controller, access point or other digital electronic device, as applicable (an “Electronic Device”), and you may access and use that Software as installed on that Electronic Device so long as only one copy of such Software is in operation. For a standalone Software application, you may install, use, access, display and run only the number of copies of the Software to which you are entitled. You may make one copy of the Software in machine readable form for backup purposes only, provided that the backup copy must include all copyright or other proprietary notices contained on the original. In the absence of a support contract, you are entitled, for a period of ninety (90) days from when the instance of Software (or hardware including the Software) are first shipped by Zebra or downloaded by End-User Customer, to obtain, if available, updates, from Zebra and operational technical support, not including implementation, integration or deployment support (“Entitlement Period”). You may not obtain updates from Zebra after the Entitlement Period, unless covered by a Zebra support contract or other written agreement with Zebra.
Certain items of the Software may be subject to open source licenses. The open source license provisions may override some of the terms of this EULA. Zebra makes the applicable open source licenses available to you on a Legal Notices readme file available on your device and/or in System Reference guides or in Command Line Interface (CLI) Reference guides associated with certain Zebra products. -
Authorized Users. For a standalone Software application, the licenses granted are subject to the condition that you ensure the maximum number of authorized users accessing and using the Software either alone or concurrently is equal to the number of user licenses for which you are entitled to use either through a Zebra channel partner member or Zebra. You may purchase additional user licenses at any time upon payment of the appropriate fees to the Zebra channel partner member or Zebra.
-
Software Transfer. You may only transfer this EULA and the rights to the Software or updates granted herein to a third party in connection with the support or sale of a device which the Software accompanied or in connection with a standalone Software application during the Entitlement Period or as covered by a Zebra support contract. In such event, the transfer must include all of the Software (including all component parts, the media and printed materials, any upgrades, and this EULA) and you may not retain any copies of the Software. The transfer may not be an indirect transfer, such as a consignment. Prior to the transfer, the end user receiving the Software must agree to all the EULA terms. If Licensee is purchasing Zebra Products and licensing Software for end use by a U.S. Government end user, Licensee may transfer such Software license, but only if: (i) Licensee transfers all copies of such Software to the U.S. Government end user or to an interim transferee, and (ii) Licensee has first obtained from the transferee (if applicable) and ultimate end user an enforceable end user license agreement containing restrictions substantially identical to the ones contained in this Agreement. Except as stated in the foregoing, Licensee and any transferee(s) authorized by this provision may not otherwise use or transfer or make available any Zebra software to any third party nor permit any party to do so.
-
RESERVATION OF RIGHTS AND OWNERSHIP. Zebra reserves all rights not expressly granted to you in this EULA. The Software is protected by copyright and other intellectual property laws and treaties. Zebra or its suppliers own the title, copyright and other intellectual property rights in the Software. The Software is licensed, not sold.
-
LIMITATIONS ON END USER RIGHTS. You may not reverse engineer, decompile, disassemble, or otherwise attempt to discover the source code or algorithms of, the Software (except and only to the extent that such activity is expressly permitted by applicable law not withstanding this limitation), or modify, or disable any features of, the Software, or create derivative works based on the Software. You may not rent, lease, lend, sublicense or provide commercial hosting services with the Software.
-
CONSENT TO USE OF DATA. You agree that Zebra and its affiliates may collect and use technical information gathered as part of the product support services related to the Software provided to you that does not personally identify you. Zebra and its affiliates may use this information solely to improve their products or to provide customized services or technologies to you. At all times your information will be treated in accordance with Zebra’s Privacy Policy, which can be viewed at:
http://www.zebra.com. -
LOCATION INFORMATION. The Software may enable you to collect location-based data from one or more client devices which may allow you to track the actual location of those client devices. Zebra specifically disclaims any liability for your use or misuse of the location-based data. You agree to pay all reasonable costs and expenses of Zebra arising from or related to third party claims resulting from your use of the location-based data.
-
SOFTWARE RELEASES. During the Entitlement Period, Zebra or Zebra’s channel partner members may make available to you software releases as they become available after the date you obtain your initial copy of the Software. This EULA applies to all and any component of the release that Zebra may make available to you after the date you obtain your initial copy of the Software, unless Zebra provides other license terms along with such release. To receive Software provided through the release, you must first be licensed for the Software identified by Zebra as entitled to the release. We recommend that you periodically check availability of a Zebra support contract to ensure that you are entitled to receive any available Software releases. Some features of the Software may require you to have access to the internet and may be subject to restrictions imposed by your network or internet provider.
-
EXPORT RESTRICTIONS. You acknowledge that the Software is subject to export restrictions of various countries. You agree to comply with all applicable international and national laws that apply to the Software, including all the applicable export restriction laws and regulations.
-
ASSIGNMENT. You may not assign this Agreement or any of your rights or obligations hereunder (by operation of law or otherwise) without the prior written consent of Zebra. Zebra may assign this Agreement and its rights and obligations without your consent. Subject to the foregoing, this Agreement shall be binding upon and inure to the benefit of the parties to it and their respective legal representatives, successors and permitted assigns.
-
TERMINATION. This EULA is effective until terminated. Your rights under this License will terminate automatically without notice from Zebra if you fail to comply with any of the terms and conditions of this EULA. Zebra may terminate this Agreement by offering you a superseding Agreement for the Software or for any new release of the Software and conditioning your continued use of the Software or such new release on your acceptance of such superseding Agreement. Upon termination of this EULA, you must cease all use of the Software and destroy all copies, full or partial, of the Software.
-
DISCLAIMER OF WARRANTY. UNLESS SEPARATELY STATED IN A WRITTEN EXPRESS LIMITED WARRANTY, ALL SOFTWARE PROVIDED BY ZEBRA IS PROVIDED “AS IS” AND ON AN “AS AVAILABLE” BASIS, WITHOUT WARRANTIES OF ANY KIND FROM ZEBRA, EITHER EXPRESS OR IMPLIED. TO THE FULLEST EXTENT POSSIBLE PURSUANT TO APPLICABLE LAW, ZEBRA DISCLAIMS ALL WARRANTIES EXPRESS, IMPLIED, OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY, SATISFACTORY QUALITY OR WORKMANLIKE EFFORT, FITNESS FOR A PARTICULAR PURPOSE, RELIABILITY OR AVAILABILITY, ACCURACY, LACK OF VIRUSES, NON INFRINGEMENT OF THIRD PARTY RIGHTS OR OTHER VIOLATION OF RIGHTS. ZEBRA DOES NOT WARRANT THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR FREE. TO THE EXTENT THAT THE SOFTWARE COVERED BY THIS EULA INCLUDES EMULATION LIBRARIES, SUCH EMULATION LIBRARIES DO NOT WORK 100% CORRECTLY OR COVER 100% OF THE FUNCTIONALITY BEING EMULATED, ARE OFFERED “AS IS” AND WITH ALL FAULTS, AND ALL THE DISCLAIMERS AND LIMITATIONS CONTAINED IN THIS PARAGRAPH AND THIS AGREEMENT APPLY TO SUCH EMULATION LIBRARIES. SOME JURISDICTIONS DO NOT ALLOW EXCLUSIONS OR LIMITATIONS OF IMPLIED WARRANTIES, SO THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. NO ADVICE OR INFORMATION, WHETHER ORAL OR WRITTEN, OBTAINED BY YOU FROM ZEBRA OR ITS AFFILIATES SHALL BE DEEMED TO ALTER THIS DISCLAIMER BY ZEBRA OF WARRANTY REGARDING THE SOFTWARE, OR TO CREATE ANY WARRANTY OF ANY SORT FROM ZEBRA.
-
THIRD-PARTY APPLICATIONS. Certain third party applications may be included with, or downloaded with this Software. Zebra makes no representations whatsoever about any of these applications. Since Zebra has no control over such applications, you acknowledge and agree that Zebra is not responsible for such applications. You expressly acknowledge and agree that use of third party applications is at your sole risk and that the entire risk of unsatisfactory quality, performance, accuracy and effort is with you. You agree that Zebra shall not be responsible or liable, directly or indirectly, for any damage or loss, including but not limited to any damage to or loss of data, caused or alleged to be caused by, or in connection with, use of or reliance on any such third party content, products, or services available on or through any such application. You acknowledge and agree that the use of any third-party application is governed by such third party application provider’s Terms of Use, License Agreement, Privacy Policy, or other such agreement and that any information or personal data you provide, whether knowingly or unknowingly, to such third-party application provider, will be subject to such third party application provider’s privacy policy, if such a policy exists. ZEBRA DISCLAIMS ANY RESPONSIBILITY FOR ANY DISCLOSURE OF INFORMATION OR ANY OTHER PRACTICES OF ANY THIRD PARTY APPLICATION PROVIDER. ZEBRA EXPRESSLY DISCLAIMS ANY WARRANTY REGARDING WHETHER YOUR PERSONAL INFORMATION IS CAPTURED BY ANY THIRD PARTY APPLICATION PROVIDER OR THE USE TO WHICH SUCH PERSONAL INFORMATION MAY BE PUT BY SUCH THIRD PARTY APPLICATION PROVIDER.
-
LIMITATION OF LIABILITY. ZEBRA WILL NOT BE LIABLE FOR ANY DAMAGES OF ANY KIND ARISING OUT OF OR RELATING TO THE USE OR THE INABILITY TO USE THE SOFTWARE OR ANY THIRD PARTY APPLICATION, ITS CONTENT OR FUNCTIONALITY, INCLUDING BUT NOT LIMITED TO DAMAGES CAUSED BY OR RELATED TO ERRORS, OMISSIONS, INTERRUPTIONS, DEFECTS, DELAY IN OPERATION OR TRANSMISSION, COMPUTER VIRUS, FAILURE TO CONNECT, NETWORK CHARGES, IN-APP PURCHASES, AND ALL OTHER DIRECT, INDIRECT, SPECIAL, INCIDENTAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES EVEN IF ZEBRA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. NOTWITHSTANDING THE FOREGOING, ZEBRA’S TOTAL LIABILITY TO YOU FOR ALL LOSSES, DAMAGES, CAUSES OF ACTION, INCLUDING BUT NOT LIMITED TO THOSE BASED ON CONTRACT, TORT, OR OTHERWISE, ARISING OUT OF YOUR USE OF THE SOFTWARE OR THIRD PARTY APPLICATIONS, OR ANY OTHER PROVISION OF THIS EULA, SHALL NOT EXCEED THE FAIR MARKET VALUE OF THE SOFTWARE OR AMOUNT PURCHASER PAID SPECIFICALLY FOR THE SOFTWARE. THE FOREGOING LIMITATIONS, EXCLUSIONS, AND DISCLAIMERS (INCLUDING SECTIONS 10, 11, 12, AND 15) SHALL APPLY TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, EVEN IF ANY REMEDY FAILS ITS ESSENTIAL PURPOSE.
-
INJUNCTIVE RELIEF. You acknowledge that, in the event you breach any provision of this Agreement, Zebra will not have an adequate remedy in money or damages. Zebra shall therefore be entitled to obtain an injunction against such breach from any court of competent jurisdiction immediately upon request without posting bond. Zebra’s right to obtain injunctive relief shall not limit its right to seek further remedies.
-
MODIFICATION. No modification of this Agreement shall be binding unless it is in writing and is signed by an authorized representative of the party against whom enforcement of the modification is sought.
-
U.S. GOVERNMENT END USERS RESTRICTED RIGHTS. This provision only applies to U.S. Government end users. The Software is a “commercial item” as that term is defined at 48 C.F.R. Part 2.101, consisting of “commercial computer software” and “computer software documentation” as such terms are defined in 48 C.F.R. Part 252.227-7014(a)(1) and 48 C.F.R. Part 252.227-7014(a)(5), and used in 48 C.F.R. Part 12.212 and 48 C.F.R. Part 227.7202, as applicable. Consistent with 48 C.F.R. Part 12.212, 48 C.F.R. Part 252.227-7015, 48 C.F.R. Part 227.7202-1 through 227.7202-4, 48 C.F.R. Part 52.227-19, and other relevant sections of the Code of Federal Regulations, as applicable, the Software is distributed and licensed to U.S. Government end users (a) only as a commercial item, and (b) with only those rights as are granted to all other end users pursuant to the terms and conditions contained herein.
-
APPLICABLE LAW. This EULA is governed by the laws of the state of Illinois, without regard to its conflict of law provisions. This EULA shall not be governed by the UN Convention on Contracts for the International Sale of Goods, the application of which is expressly excluded.
Zebra Technologies Corporation
3 Overlook Point Lincolnshire, Illinois 60069 USA http://www.zebra.com
ZEBRA and the stylized Zebra head are trademarks of
Zebra Technologies Corporation, registered in many jurisdictions worldwide.
All other trademarks are the property of their respective owners. ©2018-2021
Zebra Technologies Corporation and/or its affiliates. All rights reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>