STEAJIC AB403 Portable MagSafe Stand User Manual
- June 15, 2024
- STEAJIC
Table of Contents
STEAJIC AB403 Portable MagSafe Stand
Specifications
- Boundary dimension: 60x49x243mm
- Developed dimension: 1365mm
- Weight: 275g
- Material: ABS (fireproofing) PC (fireproofing)
- Bluetooth transmission distance: 10m
- Battery capacity: 50mAh
- Aluminum alloy
Product Usage Instructions
Unfolding and Setting Up the Phone Holder
Unfold the phone holder to be upright.
Detaching and Attaching the Remote Controller
- Pull the center rod to leave space for sliding out the Bluetooth Remote Controller.
- Slide the Bluetooth Remote back in the slot to attach the remote with the tripod.
- When the battery is low, detach the remote controller and charge it with the Micro USB included in the package.
Connecting Bluetooth
- Long press the shutter/power button on the remote controller for 3 seconds until the green light flashes.
- On your device, go to Settings > Bluetooth and turn on Bluetooth.
- Find SEAJIC to connect. When pairing is completed, the green light will go off.
Taking Pictures
- Short press the shutter/power button to take pictures when the connected smartphone is in camera mode.
Turning Off Bluetooth
- Long press the shutter/power button for 3 seconds again to turn off the Bluetooth.
FAQ
Can I charge the remote controller separately?
Yes, you can detach the remote controller and charge it with the Micro USB included in the package.
What is the Bluetooth transmission distance?
The Bluetooth transmission distance is 10 meters.
Can I use the product without restrictions in terms of RF exposure?
Yes, the device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction.
Product Introduction
Release Tripod
-
Step 1:
Press the triangle button on the bottom of the tripod to release tripod legs. -
Step 2:
Unfold the phone holder to be upright. -
Step 3:
Hold the handle sleeve with one hand and the pull handle of the phone holder with the other hand to pull out the telescopic rod. Adjust to desired height.
Tripod legs will open automatically as the telescopic rod being pulled out.
Fold Tripod
Hold the handle sleeve with one hand and push the telescopic rod back in.
Attention
- Do not pull legs to open tripod.
- Push the handle sleeve all the way down so that the tripod legs are fully opened and stable.
Detach/Attach Remote Controller & Charging
The remote controller of this product is detachable. Pull the center rod to
leave space for sliding out the Bluetooth Remote Controller. Slide the
Bluetooth Remote back in the slot to attach the remote with the tripod.
When the battery is low, detach the remote controller and charge with the
Micro USB included in the package.
Connect Bluetooth
Long press the shutter/power button on the remote controller for 3 seconds until the green light flashes. On your device, go to Settings > Bluetooth and turn on Bluetooth. Find “SEAJIC” to connect. When pairing is completed, the green light will go off.
Short press the shutter/power button to take pictures when the connected smartphone is in camera mode. Long press for 3 seconds again to turn off the Bluetooth.
Specifications
Tripod Parameters:
- Boundary dimension: 60x49x243mm
- Developed dimension: 1365mm
- Weight: 275g
- Material: ABS (fireproofing) PC (fireproofing) Aluminum alloy
- Bluetooth transmission distance: 10m
- Battery capacity: 50mAh
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Web:www.dgosmtech.com
Standard:Q/OSL 001-2019
Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>