STEAJIC OTHAB305 Wireless Charging Photographic Handle User Manual
- June 13, 2024
- STEAJIC
Table of Contents
STEAJIC OTHAB305 Wireless Charging Photographic Handle
Product Information
| Model Number | Oth-AB305 |
|---|---|
| Website | www.osmdigi.com |
| Standard | Q/OSL 001-2019 |
| Manufacturer | Made in China |
Product Usage Instructions
Product Introduction:
- Power button: Press once to power on and press twice to power off.
- Ring magnet: Used for attaching the handle to a compatible surface.
- Reset hole: A small hole for resetting the device ifneeded.
- Indicator: Shows various status of the device.
- Bluetooth/camera button: Controls Bluetooth connectivity and camera functions.
- Magnetic ring: Enables wireless charging when placed on a compatible charging pad.
- Wireless charging panel: Area where wireless charging takes place.
- Floor mat: Provides stability and prevents slipping.
- TYPE-C charging jack: Used for charging the device via a Type-C cable.
- 1/4 nut: Allows attachment to compatible accessories with a 1/4″ screw.
Power button:
Press once to power on the device and press twice to power itoff.
Indicators:
- 4 white power indicators: Always on during working and flicker when the battery is low.
- 1 blue wireless charging indicator: Always on during working and flicker in standby mode.
Note:
If the Bluetooth doesn’t work, please enable it again by poking with your SIM card pin or another hard object. It is recommended to charge the device every 6 months for static storage duration in shutdown mode.
Product Specifications:
| Parameter | Value |
|---|---|
| Boundary dimension | 120x87x50mm |
| Weight | 216g |
| Bluetooth transmission distance | 10m |
| Input/output voltage | 5/9/12V (maximum 18W) |
| Input/output interface | Type-C |
| Wireless charging efficiency | 75% (max) |
| Wireless charging power | 5W/7.5W/10W |
| Battery capacity/voltage | 5,000mAh/3.7V (18,650/2,500 mAh*2) |
| Material | ABS (fireproofing), PC (fireproofing), Aluminum alloy |
FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority to operate the equipment. The device has been evaluated to meet general RF exposure requirements and can be used in portable exposure condition without restriction.
Product Introduction
- Power button: press once to power on and press twice to power off。
- 4 white power indicators: always on during working and flicker in low battery。
- 1 blue wireless charging indicator: always on during working and flicker in standby mode。
-
Bluetooth pairing:
Press and hold it for 2 seconds to power on。When the green indicator flickers, enable Bluetooth on your mobile phone to search for “SEA JIC”, then click on it to connect; the green indicator will be always on after successful connection。 -
To take photos/videos, just short press “Bluetooth/Camera” (some phones may not support taking videos)。
-
It will enter sleep mode in case of no connection or no key operation in 10minutes after connection, and will be shut down automatically in 30 minutes in sleep mode。
- Note: when the Bluetooth doesn’t work, please enable it again by poking with your SIM card pin or another hard object。Static storage duration in shutdown mode: charging it every 6 months is recommended。
Specifications
Parameters of the Magnetic Wireless Charger:
- Boundary dimension: 120x87x50mm
- Weight: 216g
- Bluetooth transmission distance: 10m
- Input/output voltage: 5/9/12V (maximum 18W)
- Input/output interface: Type-C
- Wireless charging efficiency: 75% (max)
- Wireless charging power: 5W/7.5W/10W
- Battery capacity/voltage: 5,000mAh/3.7V (18,650/2,500 mAh*2)
- Material: ABS (fireproofing) PC (fireproofing) Aluminum alloy
FCC
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
- Web:www.kraftgeek.com.
- Standard: Q/OSL 001-2019
- Made in China
References
- Reinvent the Creative Process | KraftGeek | Premium Tripods & Add-ons
- China Satatic Live Streaming Kit, Beauty Live Stream, Camera Photography Tripod Suppliers,Tripod bracket stand Manufacturers, Factory - OSM GROUP
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>