MUNJUN ‎52QF-8704 Wood Ceiling Fan Owner’s Manual

Ceiling Fan
OWNER’S MANUAL
READ AND SAVE THESE INSTRUCTIONS

Warning

WARNING:To avoid fire,shock and serious personal injury, Please read the following instructions carefully.
Important Safety Instructions

1. Read all instructions and safety information before installing your new fan Review the accompanying assembly diagrams.

2. Before installing the fan, disconnect the power by removing fuses or turning off circuit breakers.

3. Make sure all electrical connections comply with local codes, ordinances, or National Electrical Codes. Hire a qualified electrician or consult a do-it-yourself wiring handbook if you are unfamiliar with installing electrical wiring.

4. Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the trailing edge of the blades.

5. If you are mounting the fan on a ceiling outlet box. use a metal outlet box. Secure the box directly to the building structure. The outlet box and its support must be able to support the moving weight of the fan (at least 50 Ibs.). Do not use a plastic outlet box.
   Attach the mounting bracket by using the hardware supplied with the ceiling outlet box.

6. If you are mounting the fan to a joist, make sure Itis strong enough to support the moving weight of the fan (at least 50 Ibs.)

7. After installing the fan, make sure all the connections are secured. This will prevent the fan from falling.

8. Do notinsert anything into the fan blades while the fan is operating.

9. Turn the fan off and wait for it to stop before reversing fan direction

10. To reduce risk of electrical shock and personal injury, do not install the fan on a sloped ceiling.

11. To reduce the risk of electrical shock and personal injury, do not use this fan with any solid-state.

12. To reduce risk of personal injury,use only the two steel screws and lock washers provided with the fan for mounting the outlet box.

ASSEMBLY DRAWING &PARTS LIST-WITHOUT LIGHT

Unpacking Your Fan
Unpack your fan and check the contents. Please check each item prior to installation.
To reduce the chance of marks or possible damages, please remove the parts when required for installation

ASSEMBLY DRAWING & PARTS LIST-WITH LIGHT
Unpacking Your Fan
Unpack your fan and check the contents. Please check each item prior to installation.
To reduce the chance of marks or possible damages, please remove the parts when required for installation.

HOW TO INSTALL THE FAN-WITHOUT LIGHT

1. Secure the suspension bracket to the ceiling joists using the provided tension bolts, flat gaskets, and spring gaskets. (Figure1)

2. Install the fan blades and blade decorative plate by aligning the holes on the blade and plate with the holes on the fan motor assembly set by the provided set screws.(Figure 2) Make sure the set screws securing the blade are tight and the blades are properly sealed

3. Loosen the set screws in the Hange rBall assembly untitl the ball slides carefully down the downrod. Remove the Pin from the downrod (Figure 3) -Re-install the hanger ball after step 5 below

4. Remove and save the clevis pin and hairpin of the downrod.Put the downrod through the canopy and coupling cover. (Figure 4)

5. Loosen lwa set screws on the downrod support and then place the downrod into thedownrod support(Figure 5). Thread the electrical wires and the earth wire through the downrod. Align the holes in the Downrod with the holes in the Downrod Support.
   Be sure o push the straight lag of the Hairpin Clip through the hole near the end of the Clevis Pin unti the curved portion of the Hairpin snapsaround the Clevis Pin Finally, re-tighlen the two set screws.
   WARNING
   Itis critical that the clevis screwinthe do_warod supportis properly installed and the set screws are securely tightened. Failu e to verify the clevis screw, hairpinclipand sets ~ crewsare properly ins talled could resultin the fan falling.

6. Carefully lift the fan. and set the downrod / hanger ball assembly on the hanger bracket attached to the ceiling joist. Be sure the groove in the ball is properly aligned with the tab on the hanger bracket. (Figure 6) WARNING
   The fan must be hung with at least 230 cm of clearance from floor to b lades.

7. Connections:
   WARNING
   Toavoid possible electrica Ishock, be sure electricity is turned off at the main fuse hox before wiring Connect 110V-130V main power (dwelling) to theTerminal Block located on the hanger bracket.Plug the receiver in the hanger bracket with theflat side facing up.
   -Insert the 3P connector of hanger bracket into the AC POWER INPUT socket of receiver
   -Insert the 3P motor connector of fan motor assembly into the 3P MOTOR socket of receiver
   -Connect the 1P yellow/green connectors of fan motor assembly and hanger bracket. (Figure 7)

8. Mount the canopy by tightening the two screws. (Figure 8)

9. Install the rubber plug into the motor axis. (Figure 9)

HOW TO INSTALL THE FAN-WITH LIGHT

1. Install the hanger bracket as previously stated (Figure 1)
2. Install the fan blades by aligning the holes on the blade with the holes on the fan motor assembly set by the provided set screws and washers.(Figure 11)  Make sure the set screws securing the bladeare tight and the blades are properly seated.
3. Connect the canopy,downrod coupling cover and fan motor assembly as previously stated (Figure 3,4and 5)
4. Liftthe fan as previously stated.(Figure 6)
5. Connect the wires from the motor assembly and wires from the LED correctly.Arrach the light kit plate to the fan motor assembly using the two light kit plate screws. (Figure 12)
6. Install the shade into light plate. Make sure it is secure but not overly tight. (Figure 12)
7. Connections:
   WARNING
   To avoid possibleelectricalshock be sure electricity is turned off at the main fuse box before wiring
   Connect 110V-130V main power (dwelling)to the Terminal Block located on the hanger bracket. Plug the receiver in the hanger bracket with the flat side facing up.
   – Insert the 3P connector of hanger bracket into the AC POWER INPUT socket of receiver -Insert the 2P light connector of fan motor assembly into the 2P LIGHT socket of receiver
   -insert the 3P motor connector of fan motor assembly into the 3P MOTOR socket of receiver
   -Connect the 1P yellow/green connectors of fan motor assembly and hanger bracket. (Figure 7)
8. Mount the canopy as previously stated. (Figure 8)

REMOTE CONTROL SETTING AND OPERATION

4 Kindly Renminders

1. Learning code maching mode Is used between emitter and receiver. Turn “ON” the supply power within 30 seconds and press the emitter’s *3 OFF the fan’ button for 5 seconds, itcan load normally after hearing a long sound “bee”, which means learning successfully and it can works normally. (PS: Leaming mode is not accepted after turn “ON” the supply power 30 seconds)
2. When the emitter cannot control the receiver, please check the battery switch touching normally or not, correction of the positive and negative, full or empty of the power.
3. When the emitter cannot the receiver. please check there any existence of similar remote controlled products nearby, then check whether they works, because remote controlled product with the same frequency will disturb each other.
4. Low voltage of battery will affect the sensitibity of the emitter and the signal reception acordingly (the indicated light will flash out its waming when the battery get low voltage). must replace if battery is getting low voltage.
5. Please take out the battery from the emitter when leaving unused for long time
6. When installing the fan, the fan ceiling cover don’t press the antenna(or other wire). itis easy to breakdown the wire and short – circuited.

REMOTE CONTROL

1. Turn off all loads
2. Fan speed control
3. LED indicator light
4. Turn on the light (This product does not have this feature * Please Ignore)
5. Fan off
6. Fan positive and negative rotation control
7. Fan timing control

IMPORTANT:PAIRING BETWEEN REMOTE AND RECEIVER

1. Tum ON“the powar supply and within 30 secondspress and holdthe transmiters “FAN ON/OFF”button for 5 seconds and a*beep“will be heard this will then activate a successful pairing and all functions will work normally.
   IMPORTANT:
   pairing initial step must be performed within 30 seconds of power being turned on.
   1(a). when pairing multiple fans please ensure the isolation swich or power supply to the first installed fan is turned off prior to pairing futher fans e.g please pair one fanatatime
   1(b). please ensure isolation switch is kept to the ON position, the isolation swilch is not to be used as a light switch as this will damage and make the remote recevier inoperable

2. If the transmitter functions are not working please check the battery orientation and power ievel.Low battery voltage will affect the functions of your transmitter and operation of your fan.Other remote controls nearby using the same frequency may cause interference with the Fans receiver.

3. Please remove batteries from the transmitter if leaving unused for an extended period of time.

4. Remote supports 200w maximum on lighting side.

IMPORTANT RECEIVERS

1. Please note: Receiver must be correctly installed in the mounting bracket on fan
2. When the transmitter cannot control the receiver, please check the battery hassufficient charge i the transmitter.
3. When the transmitter cannot control the receiver, please check if there is any existence of similar remote controlled products nearby, causing interference with each other.
4. Low power of battery wil affect the sensilivily of the transmitter and the signal reception accordingly, must replace if the batlery is getling low power.
5. Please take the battery out from the transmitter when leaving unused for along time, to avoid battery leaks
6. Isolation Switch “Must be connected in the line.”
7. When power is cut to the unit (via a blackout or otherwise) when power is restored the light will come on.

Before carrying out any cleaning or mainlenance wark, always make sure that the appliance is disconnected LED lights are not removable, LED lights can only be used within the product delivery, thoy can not bo replaced.

PROTECTIVE FUNCTIONS OF THE RECEIVER

Lock protection- The DC motor has a built-in safety feature against blade or motor obstruction during operation. If something obstructs the fan blades or molor, the motor will keep trying to run and then stop operation after about 30 seconds of interruption, Please remove obstacles and reset. To reset: Turn the fan off by remote transmitter and then turn the fan on Over load protection (current limit)- The device will limit the maximum current output from the receiver/drive if the fan load has increased abnormally.
Tips

1. If your fan is operates automatically after installation and power on, itis because your fan has memorized the previous factory setting. Use the Universal Mode o the learning function and your fan will be ready for use.
2. Ifthe fan or light isn’t working, reset power (turn the power off for at least 5 seconds and then turn the power back on) and redo the leam function setting
3. ltis not possible to remotely operate more than one fan in the same room (in the area where the remote sianal can reach to) if they share the same power supply. Separate power supplies (such as using individual wall switches for each fan) is required if you want to separately conltrol more than one fanin same room
4. When the fan is tumed on or operated using forward/reverse function, it shutters & goes back & forth until it tumns
   This is a normal and it will take a few seconds to run this operation.

MAINTENANCE

1. Periodic cleaning of your new ceiling fan is the only maintenance that is needed
2. When cleaning, use only a soft brush or lint free cloth to avoid scratching the finish
3. Abrasive cleaning agents are not required and should be avoided to prevent damage tofinish

WARNING
Do not use solvents when cleaning your ceiling fan, It could damage the motor and create the possibility of electrical shock

RECOMMENDED:
Periodically check that the blade sets to the fan motor setscrews are secure and tight.

BALANCING FAN/WOBBLING TROUBLE SHOOTING

Please note that all ceiling fans are not the same, even in the same model- some may move more or less than others.
Movement of a couple of centimeters is quite acceptable and does not suggest the fan will fall down.
Even though all blades are weighted and grouped by weight. it is impossible to eliminate wobble altogether.
This should not be considered a faut. Ceiling fans tend to move during operation due to the fact that they are not generally rigidly mounted
TRY THE FOLLOWING TO REDUCE A WOBBLING FAN:

1. Check that all of the blade mounting screws are tightened and secure.
2. Wobbling problems may result from inconsistent blade level. To check the blade level, measure the distance from each blade tip to the ceiling, Note: If measurements are inconsistent:
   -Be sure the blade mount screws are not too tight or too loose, which may cause wobbling due to an unlevel blade lip
   -An out of shape blade can cause wobbling. Check by removing the blade and placing on a flat surface.
3. Blade tracking may be checked simply by use of a household ruler. Place the ruler vertically against the ceiling and even with the outside leading edge of a blade. Note the distance of the edge of a blade compared to the others. Turn the blade slowly by hand to check the remaining blades. ifa blade is not in alignment, the blade is either out of shape, warped or the blade screws are not evenly tighten or either loose.

BALANCINGKIT
ABalancing Kit has been provided to assist with reducing a wobble. Please retain the kit as it may become useful should the fan develop a wobble in the future, Instructions on how to use the Balancing kit can be found within the Kit

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>