Vizolink Q100 Conference Omnidirectional Speaker User Manual

Vizolink Q100 Conference Omnidirectional Speaker

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions

1. this device may not cause harmful interference
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party re- responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. However. there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi- sion reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
• NOTE : This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

 Packing List

Please read the instruction manual carefully before using the product and keep it in a safe place.

Product Description

The illustrations of products, accessories, user interface, etc. in the manual are schematic diagrams and are for reference only. Due to product updates and upgrades, there may be slight differences between the actual product and the schematic diagram, please refer to the actual product.

1. Type-C Power Port
2. Omni-Directional Noisel
3. Reduction Microphone X 6
4. System Indicator
5. Call answer/end key
6. Volume “-” key
7. Mute Key/Mute Indicator Light
8. Volume “+” Key
9. Pause/Play Key
10. Charging Indicator Light
11. Power Key
12. Bluetooth Key

Instructions For Use

Power On/Off

• Press and hold the power button on the side for 3-5 seconds to turn on/off. accompanied by a sound for turning on/off..

Charging

• This product can be powered by a built-in rechargeable battery or connected to an external power source. When charging is required, please connect the Type-C end of the charging cable to this product, and connect the other end of the charging cable to power supply devices such as power adapters, computers, and mobile nower sunniest

Charging indicator status

Check the remaining power

• Press the power button on the side of the device lightly, if the power is 100%, all 5 button lights on the front of the device will light up (each button light from left to right on the front of the device represents 20%

System indicator status

Button function

Connection Method

Connect to the computer via a USB cable or wireless receiver

1.  Plug this product into the Type-A port of the computer through a USB cable or a wireless receiver;
2. In the computer sound setting, set “Q100” as the default audio input and output device;
3. Select “Q100” for the speaker and microphone in the conference software.

Notice:

• If you do not set “Q100” as an audio device in the conference software, it may cause problems that affect the quality of the call due to unclear sound pickup, and it is not a device failure.

Connect to the mobile device via Bluetooth

1. When the product is turned on, short-press the Bluetooth button once to enter the pairing mode, and the blue light of the system indicator flashes at this time;
2. Turn on the Bluetooth of the mobile device and choose to connect to “Q100” to perform Bluetooth pairing;
3.  After the pairing is successful, the blue light of the system indicator light is always on, accompanied by the sound of “Bluetooth connected”;
4. Short press the Bluetooth button again to disconnect the Bluetooth connection, accompanied by the sound of “Bluetooth disconnected”;

Notice:

• When the product is powered on for the first time, it will automatically enter the Bluetooth pairing mode;
• Every time you turn on the power, this product will automatically connect to your last successfully connected mobile device (if available); if you need to clear the historical Bluetooth pairing information, please press and hold the Bluetooth button for 5 seconds.

Product Parameters

• The data comes from internal testing, and the actual situation is affected by factors such as the use environment

The Name and Content of Harmful Substances in the Product

Safety Warning

1.  Do not place the device and its battery in a high-temperature place or around heating devices, such as sunlight, microwave ovens, heaters, ovens, etc. Overheating of the battery may cause an explosion.
2. If you use a power adapter to charge, you should use a power adapter that meets product specifications and has passed CCC certification.
3. This device is not a waterproof device, and it is strictly forbidden to use the device after it is sprayed or soaked in water.
4. Do not disassemble, impact, squeeze, or throw the battery of this product into fire. If there is severe swelling, please do not continue to use it.
5. Do not short-circuit the metal contacts of the battery, which may cause a short-circuit hazard, and avoid personal injuries such as scalds and burns caused by overheating of the battery;
6. Do not disassemble, collide, or squeeze the battery to avoid leakage, overheating, and explosion;
7. Do not throw the battery into the fire, otherwise it will cause fire or explosion;
8. If the battery is severely swollen, please do not continue to use it;
9. Please do not throw the battery into domestic garbage for disposal. Improper disposal of the battery may cause the battery to catch fire and explode. Dispose of the device, battery, and other accessories in accordance with local regulations. Product identification information is located on the bottom case of the product.

After-sales Service Warranty Card

Hello, dear user! Thank you for choosing this product. To make you more satisfied with our after-sales service, please read and properly keep this warranty card after purchasing this product. If there is a quality problem with the purchased product, please fill in this warranty card and contact the manufacturer for feedback in time. The warranty period of this product is calculated from the date of purchase. If it is registered and used without dismantling and maintenance, and is confirmed by the warranty personnel as a product quality problem, it will enjoy warranty service within one year. Since the packaging box is required to ensure the safety of product transportation during transportation, it is recommended that you keep the packaging for at least 30 days from the date of receipt.

Name:  Contact Number

• Product Model (Mode) :
• Product Number (S/N) :
• Product Order Number:
• Product Purchase Date:
• Product Problem Description:
• Contact Address:
• Contact Number

Product failures caused by the following conditions are not covered by the warranty:

1. Unauthorized maintenance, misuse, collision, negligence, abuse, liquid ingress, accident, modification, incorrect use of non-product accessories, or tearing or altering labels;
2.  The warranty period has expired;
3. Damage caused by man-made reasons or external force majeure.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>