Honszex 1200A Jump Starter Power Pack User Manual

June 14, 2024
Honszex

Honszex-Logo

Honszex 1200A Jump Starter Power Pack

Honszex-1200A-Jump-Starter-Power-Pack-product

Product Function Description

Honszex-1200A-Jump-Starter-Power-Pack-
fig1

  1. Start button
  2. Screen Display
  3. Startup power connector
  4. TypeC input: 5V/2A
  5. USB output: 5V/2A
  6. 12VDC output port
  7. USB 3.0 output: 9V/2A
  8. LED flashlight

Technical Specifications

  • Input: 5V/2A
  • Output starter: 12V
  • USB output: 5V/2A, 9V/2A
  • DC output: 12V/10A
  • Start current: 800A
  • Peak current:1200A
  • Applicable temperature range:-20°C-60°C
  • Size: 1869040mm

Package List

  • Jump starter*1
  • Charging cable*1
  • Alligator clip*1
  • User manual*1

Operating Regulations

Start the car with the jump starter

  1. Connect the alligator clips to the starter, insert one end of the alligator clip into the starter socket, and make sure the plug is firmly inserted into the starter.
  2. Connect the red battery clip to the positive (+) battery and the black battery clip to the negative (-) battery terminal. Make sure the battery clips maintain good clean contact with the battery terminals.
  3. Start the vehicle.
  4. Once the car is started, remove the alligator clips from the car battery within 30 seconds (otherwise the clips and starter will be damaged) and let the engine continue to run.

Flashlight use

How to use the flashlight

  1. Press two consecutive red and blue alarm lights flashing, and then press two times to turn off the lights.
  2. There are three white light modes, continuous bright, strobe, and SOS. long press for 3 seconds to open the constant light mode, in the constant light mode, click the switch to switch the frequency mode flash and SOS mode.

Warning

  1. When using the starter, make sure the blue plug is firmly inserted into the starter. If not, the starter will not start your car, which may cause damage to the starter.
  2. Make sure the alligator clips maintain good clean contact with the battery terminals. If the starter still does not start your car after three attempts, stop and check for other possible problems.
  3. Remove the clips from the battery terminals within 30 seconds after starting the car. Failure to do so may damage the starter.
  4. Do not connect two battery clips together. Doing so is not only dangerous but can also damage the starter.
  5. When using the starter to start the car, please make sure the starter has more than 80% power.
  6. Do not get the product wet
  7. Do not put the product into the water
  8. Do not use the product under dangerous conditions
  9. Avoid placing at temperatures above 70 degrees Celsius
  10. Avoid exposure to heat sources
  11. Please use the matching charger for charging
  12. Under extreme conditions, the battery may leak. Wipe carefully with a rag. Avoid contact with skin. In case of accidental contact with skin or eyes, rinse immediately with water. Or go to the hospital to let the doctor clean and treat.
  13. The battery should be disposed of in an environmentally friendly manner at the end of its service life.

Frequently Asked Questions

Customer questions & **answers**

  • Q: Are wall chargers included?
    A: Not included, you can charge it with a phone charger.

  • Q: If the battery is idle for a long time, how often does it need to be charged?
    A: We recommend charging once every 3 months.

  • Q: How do I know if the device is properly connected to the vehicle?
    A: Connect the car battery with the clip, when the indicator light on the booster line is solid green, it means the device is connected correctly

Honszex-1200A-Jump-Starter-Power-Pack-fig4

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals