William Morris Roller Shades Motorized Installation Guide
- June 15, 2024
- William Morris
Table of Contents
Morris Roller Shades Motorized
Installation Guide
Roller Shades Motorized
Installation Guide
Motorized
Fitting the brackets
The brackets offer two methods of installation:
Use the front two holes in the top of the bracket to fix to the the ceiling of the recess. Use two screws through the back plate to mount onto a facing surface (a wall or window frame) Note that the position of the outermost brackets should be at least 2″ away from the ends of the rail, with any other brackets evenly distributed across the width.
Fitting the shade
Holding the rail at an angle, situate the T-shaped lip on the top of the cassette into the front lip of the bracket.
Twist the back of the cassette upwards until it snaps into place against the back lip of the bracket.
Child Safety
Chain Tensioner
Shades with clutch controls come with a continuous chain loop, which should
always be screwed to the wall with the included chain tensioner.
The chain tensioner should be installed to a flat surface, so the bead chain
is taut but not stretched. Be sure not to twist or cross the chain.
On inside mount shades, the tensioner may be attached to the windowsill or to
the inside of the window frame. For outside mount or wall mount shades, the
bracket may be mounted to the exterior of the window frame or the wall.
With a pencil, mark the desired location of the screw holes for the tensioner
and then drill pilot holes. Then install the tensioner with the screws, making
sure that the tensioner is fully installed, so that the spring is pushed in
and the chain passes smoothly through the guide. The chain tensioner forms
an important safety function by keeping chain loops away from small children.
Never operate this shade without a functioning and correctly installed chain
tensioner.
Please retain these instructions for the future reference.
Thank you for purchasing this product. Please read the instructions and
warning carefully before installation to ensure safe and satisfactory use of
this product.
Installation Guide
No-Drill Blinds Headrail
The difficulty level of this installation is ranked at Level 1. A piece of
cake!
If you have questions or get stuck, call our Customer Care Team at
888-257-1840, or email
customercare@selectblinds.com
Remove the No-Drill Blinds Headrail
The No-Drill Blinds Headrail will already be installed onto the existing
product headrail.
Remove the product from the headrail (See Fig A), which will vary from product
and depend on lift type.
-
Preparing the No Drill Blinds Headrail
Pull the lever from below or push down on the mechanism from above to retract the tension boot (See Fig B).
Install the metal strips or padded adhesive tape on opposite sides of the window opening where you’ll be installing the No-Drill Blinds Headrail. This is optional and only available on larger products. -
Installing the No Drill Blinds Headrail
Insert the No-Drill Blinds Headrail into the window opening, make it flush with the top of the window opening, then push on the lever to extend the tension spring and secure the No-Drill Blinds Headrail. (See Fig C) -
Installing the Product
Install the product onto the brackets (See Fig D). Test and operate the product to ensure secure installation and smooth functionality.
Uninstalling the No Drill Blinds Headrail
To uninstall the product, follow step 1 by removing the product from the
headrail and use a screwdriver to unlatch the lever.
Make sure to hold the No Drill Blinds Headrail in place while unlatching the
lever. This will prevent damage to the window or headrail.
Tech Tip
If the fixed boot end was accidentally forced out, use a flathead screwdriver
to twist the red “droplets” towards the center and then push it back in.
INSTALLATION GUIDE | NO DRILL BLINDS HEADRAIL
UPDATED NOV 2023
Documents / Resources
|
William Morris Roller Shades
Motorized
[pdf] Installation Guide
Roller Shades Motorized, Roller, Shades Motorized, Motorized
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>