LSI 4RP Round Straight Poles Owner’s Manual

: June 9, 2024
: LSI

Table of Contents

[FEATURES & SPECIFICATIONS]](#FEATURES+%26amp%3B+SPECIFICATIONS%5D)
ORDERING GUIDE
- Pole Series
Accessory Ordering Information
DRILLING LOCATIONS
FIXTURE CONFIGURATIONS
BOLT CIRCLE
PRODUCT DIMENSIONS
WIND SPEED
Documents / Resources

LSI 4RP Round Straight Poles

FEATURES & SPECIFICATIONS]

Pole Shaft

Steel round poles are 4” or 5” in diameter
Pole shaft is electro-welded ASTM-A500 Grade C Steel Tubing with a minimum yield strength of 46,000 psi.
On Tenon Mount steel poles, tenon is high strength pipe. Tenon N option is 2-3/8” O.D. x 4-3/4” tall. Tenon 4N option is 4” O.D. x 4-7/8” tall.

Hand-Hole

Standard hand-hole location is 12” above pole base.
Poles 18’ and above have a 3” x 6” reinforced hand-hole. Shorter poles have a2” x 4” non reinforced hand-hole.

Base

Pole base is ASTM-A36 hot-rolled steel plate with a minimum yield strength of 36,000 psi.
Two-piece square base cover is optional. Decorative base cover is also available.

Anchor Bolts

Poles are furnished with anchor bolts featuring zinc-plated double nuts and washers. Galvanized anchor bolts are optional.
Anchor Bolts conform to ASTM F 1554-07a Grade 55 with a minimum yield strength of 55,000 PSI.

Ground Lug

Ground lug is standard.

Duplex Receptacle

Weatherproof duplex receptacle is optional.

Ground Fault Circuit Interrupter

• Self-testing ground fault circuit interrupter is optional.

Finishes

Every pole is provided with the DuraGrip® Protection System and a 5-year limited warranty:
When the top-of-the line DuraGrip Plus Protection System is selected, in addition to the DuraGrip Protection System, a nonporous, automotive-grade corrosion coating is applied to the lower portion of the pole interior sealing and further protecting it from corrosion. This option extends the limited warranty to 7 years.

Determining The Luminaire/Pole Combination For Your Application:

Select luminaire from luminaire ordering information.
Select bracket configuration if required
Determine EPA value from luminaire/ bracket EPA chart
Select Pole Height
Select MPH to match wind speed in the application area (See windspeed maps).
Confirm pole EPA equal to or exceeding value of luminaire/bracket EPA
Consult factory for special wind load requirements and banner brackets.

Pole Vibration Damper

A pole vibration damper is recommended in open terrain areas of the country where low steady state winds are common.
Non-tapered poles and lightly loaded poles are more susceptible to destructive vibration if a damper is not installed.

Listings

UL Listed
BAA/TAA Compliant

ORDERING GUIDE

TYPICAL ORDER EXAMPLE: 4RPU B3 S07G 24 S PLP DGP

Pole Series

| Mounting Method| Material| Height4| Mounting Configuration| Pole Finish| Options
---|---|---|---|---|---|---
4RP – 4” Diameter Round Straight Pole (New Build)

5RP – 5” Diameter Round Straight Pole (New Build)

4RPU – 4” Diameter Round Straight Pole (Retrofit )

5RPU – 5” Diameter Round Straight Pole (Retrofit)

| Bolt-On Mount 1 – See pole selection guide for patterns and fixture matches.

B5 – 5” Traditional Drilling Pattern B3 – 3” Reduced Drilling Pattern B2 – 2” Reduced Drilling Pattern

T – Tenon Mount – See pole selection guide for tenon and fixture/bracket matches.
I – No Mounting Holes1 – Use with: BKA-IFM4 – Flush Mount Adapter7
Greenlee Lifestyle CH Mounting Style
Enterprise, Lexington, Constitution PT Single Mounting2

| S07G – 07 Ga. Steel (5RP/5RPU Only) S10G – 10 Ga. Steel (4RP/4RPU Only) S11G – 11 Ga. Steel (5RP/5RPU Only)| 8’

10’

12’

14’

15’

16’

17’

17’ 6”

18’

20’

22’

22’ 6”

24’

25’

26’

27’

28’

30’

| S – Single/Parallel D180 – Double D90 – Double DN90 – Double T90 – Triple TN120 – Triple Q90 – Quad QN90 – Quad

N – Tenon Mount (Standard Tenon size is 2-3/8” O.D.)8

4N – Tenon Mount (5RPT only. For 4” poles only, use 4RPI)5

4N-6 – Tenon Mount (5RPT only. For 4” poles use 4RPI)

| BRZ – Bronze

BLK – Black

PLP – Platinum Plus

WHT – White

SVG – Satin Verde Green

GPT – Graphite

MSV – Metallic Silver

BZA – Alternate Bronze

| GA – Galvanized Anchor Bolts

SF – Single Flood3

DF – Double Flood3

DGP – DuraGrip® Plus LAB – Less Anchor Bolts CRXX – Conduit Raceway4

Accessory Ordering Information

Description| Order Number| Description Order Number
---|---|---
4″ SRBC Square Base Cover| 158450CLR| MH3 – Mounting Hole Plugs for use with 3” reduced drill pattern (3 sets of 3 plugs) 681126
5″ SRBC Square Base Cover| 158451CLR| MH2 – Mounting Hole Plugs for use with 2” reduced drill pattern (3 sets of 3 plugs) 725841
4″ /5” GBC Decorative Base Cover| 483859CLR| BB – Banner Brackets Consult Factory for

EPA calculations

ER2 – Weatherproof Duplex Receptacle (Poles below 18’)| 122557CLR|
ER2 – Weatherproof Duplex Receptacle for Reinforced Hand-hole (Poles 18′ and above)| 122566CLR
GFI – Ground Fault Circuit Interrupter (Poles below 18’)| 122558CLR
GFI – Ground Fault Circuit Interrupter for Reinforced Hand-hole (Poles 18’ and above)| 22567CLR
MH5 – Mounting Hole Plugs for use with 5” traditional drill pattern (3 set of 3 plugs)| 132336

FOOTNOTES:

See Area Light Brackets – 3” Reduced Drill Pattern and Area Light Brackets – 5” Traditional Drill Pattern Spec Sheets.
For Enterprise, Lexington, and Constitution PT mounting configuration styles, see Tenon Mount (4N) and Lifestyle Slipfit Pole Series.
Standard Flat black pole cap provided. Domed Greenlee pole cap will ship with SA4 and SA5 Enterprise and Lexington fixtures, SA Lifestyle Fixtures, BK MPT BO, and UCL Brackets.
Pole heights will have a +/- 1/2” tolerance. Max height for 4RP S10G is 24’. Max height of the 5RP S11G is 26’.
For Enterprise and Lexington D180 or other mounting configuration styles using BK MPT BO accessories order with B3 or B5 drill pattern.
See Flood Lighting Brackets section for choice of FBO Brackets.
Only use with 4 inch pole.
Use with BKA-IFM4.

DRILLING LOCATIONS

Sides	A	B	C	D
Hand-hole	X
Single	X
D180		X		X
D90	X			X
DN901
T90	X	X		X
TN1202
Q90	X	X	X	X
QN903
Single FBO	X
Double FBO		X		X

NOTES:

Two locations will be 45° to the left and right of Side A.
Other two locations will be 120° to the left and right of Side A.
Two locations will be 45° to the left and right of Side A and two locations will be 135° to the left and right of Side A.
Consult factory for custom variations. Standard SF and DF pole preparations are located 3/4 of the height of the pole from the base, except on 20’ poles. Maximum height for SF and DF pole preparations on 20’ poles is 13’ from the base.

FIXTURE CONFIGURATIONS

BOLT CIRCLE

Bolt Circle Designator	L	L	M

Bolt Circle

(19mm x 762mm)

| 1″ x 36″

(25mm x 914mm)

Anchor Bolt Projection| 3-1/4″ (83mm)| 3-1/4″

(83mm)

| 4″ (102mm)
Base Plate Opening for Wireway Entry| 3-5/8″ (92mm)| 4-3/4″ (121mm)| 4-5/8″ (117mm)
Base Plate Dimensions| 10-1/8″ sq. x 3/4″ thk. (257mm x 19mm)| 10-1/8″ sq. x 3/4″ thk. (257mm x 19mm)| 10-1/8″ sq. x 1″ thk. (257mm x 25mm)
Pole Gauge| 10| 11| 7

Note: Base plate illustrations may change without notice. Do not use for setting anchor bolts. Consult factory for the appropriate anchor bolt template.

Bolt Circle Designator	K	P	R

Bolt Circle

| Slotted

7″ – 11″ (178mm-279mm)

| Slotted

7-1/2″ – 13″ (191mm-330mm)

| Slotted

8″ – 13″ (203mm-330mm)

Anchor Bolt Size| 3/4″ x 30″

(19mm x 762mm)

| 3/4″ x 30″

(19mm x 762mm)

| 1″ x 36″

(25mm x 914mm)

Anchor Bolt Projection| 3-1/4″

(83mm)

| 3-1/4″

(83mm)

| 4″ (102mm)
Base Plate Opening for Wireway Entry| 4-1/8″ (105mm)| 5-1/8″ (130mm)| 5-1/8″ (130mm)
Base Plate Dimensions| 10″ sq. x 3/4″ thk. (254mm x 19mm)| 11-1/4″ sq. x 3/4″ thk. (286mm x 19mm)| 11-3/4″ sq. x 1″ thk. (298mm x 25mm)
Pole Gauge| 10| 11| 7

Note: Base plate illustrations may change without notice. Do not use for setting anchor bolts. Consult factory for the appropriate anchor bolt template.

PRODUCT DIMENSIONS

RPT –
N = 2-3/8″(60mm) O.D. x 4-3/4″(121mm) Tenon
4N = 4″(102mm) O.D. x 4-7/8″(124mm) Tenon
4N6 = 4″(102mm) O.D. x 6-3/8″(162mm) Tenon

SHIPPING WEIGHTS

4″(102mm) Dia. 10 Ga. is approximately| 6.0 lbs./ft.
5″(127mm) Dia. 11 Ga. is approximately| 7.0 lbs./ft.
5″(127mm) Dia. 07 Ga. is approximately| 10.0 lbs./ft.
Anchor Bolts (3/4” x 30”)(19mm x 762mm)| 15 lbs.(7kg)/set
Anchor Bolts (1” x 36”)(125mm x 914mm)| 30 lbs.(14kg)/set

Bolt-On Mount 2-Bolt Pattern

WIND SPEED

EPA Information
All LSI Industries’ poles are guaranteed to meet the EPA requirements listed. LSI Industries is not responsible if a pole order has a lower EPA rating than the indicated wind-loading zone where the pole will be located.
CAUTION: This guarantee does not apply if the pole/bracket/fixture combination is used to support any other items such as flags, pennants, or signs, which would add stress to the pole. LSI Industries cannot accept responsibility for harm or damage caused in these situations.
NOTE: Pole calculations include a 1.3 gust factor over steady wind velocity. Example: poles designed to withstand 80 MPH steady wind will withstand gusts to 104 MPH. EPAs are for locations 100 miles away from hurricane ocean lines. Consult LSI for other areas. Note: Hurricane ocean lines are the Atlantic and Gulf of Mexico coastal areas. For applications in Florida or Canada, consult factory.

Use ONLY with “Wind Speed Map for ASCE 7-10

POLE 1

| Mtg. Height Length

(ft)

|

Wall Thick (ga)

| BOLT CIRCLE| EPA
---|---|---|---|---

Designator

| Dia. (in)| Anchor bolt Dia {in}|

110 MPH

|

115 MPH

|

120 MPH

|

130 MPH

|

140 MPH

|

150 MPH

|

160 MPH

|

170 MPH

|

180 MPH

4” x 10-ga x 14’| 14| 10| L| 11| 0.75| 6.0| 5.2| 4.7| 3.9| 3.2| 2.7| 2.3| 2.0| 1.7
4” x 10-ga x 16’| 16| 10| L| 11| 0.75| 4.3| 3.7| 3.2| 2.6| 2.1| 1.8| 1.4| 1.2| 1.0
4” x 10-ga x 18’| 18| 10| L| 11| 0.75| 7.7| 6.8| 6.0| 5.0| 4.2| 3.5| 3.0| 2.5| 2.2
4” x 10-ga x 20’| 20| 10| L| 11| 0.75| 6.0| 5.2| 4.6| 3.7| 3.1| 2.5| 2.1| 1.8| 1.5
4” x 10-ga x 22’| 22| 10| L| 11| 0.75| 4.6| 3.9| 3.3| 2.6| 2.1| 1.7| 1.4| 1.1| 0.9
4” x 10-ga x 24’| 24| 10| L| 11| 0.75| 3.4| 2.7| 2.2| 1.7| 1.3| 1.0| 0.7| 0.5| n/a
5” x 11-ga x 16’| 16| 11| L| 11| 0.75| 8.7| 7.9| 7.2| 6.0| 5.0| 4.3| 3.7| 3.2| 2.8
5” x 11-ga x 18’| 18| 11| L| 11| 0.75| 12.2| 11.1| 10.1| 8.5| 7.2| 6.1| 5.3| 4.6| 4.0
5” x 11-ga x 20’| 20| 11| L| 11| 0.75| 10.0| 9.1| 8.2| 6.8| 5.7| 4.9| 4.2| 3.6| 3.1
5” x 11-ga x 22’| 22| 11| L| 11| 0.75| 8.1| 7.3| 6.6| 5.5| 4.5| 3.8| 3.2| 2.8| 2.4
5” x 11-ga x 24’| 24| 11| L| 11| 0.75| 6.5| 5.9| 5.3| 4.3| 3.5| 2.9| 2.4| 2.0| 1.7
5” x 11-ga x 26’| 26| 11| L| 11| 0.75| 5.2| 4.6| 4.1| 3.2| 2.6| 2.1| 1.7| 1.4| 1.1
5” x 7-ga x 18’| 18| 7| M| 11| 1.00| 19.7| 17.9| 16.4| 13.8| 11.7| 10.1| 8.8| 7.7| 6.8
5” x 7-ga x 20’| 20| 7| M| 11| 1.00| 16.5| 15.0| 13.7| 11.5| 9.8| 8.4| 7.3| 6.3| 5.6
5” x 7-ga x 22’| 22| 7| M| 11| 1.00| 14.0| 12.7| 11.5| 9.6| 8.1| 7.0| 6.0| 5.2| 4.6
5” x 7-ga x 24’| 24| 7| M| 11| 1.00| 11.8| 10.6| 9.6| 8.0| 6.8| 5.7| 4.9| 4.2| 3.7
5” x 7-ga x 26’| 26| 7| M| 11| 1.00| 9.9| 8.9| 8.0| 6.7| 5.6| 4.7| 4.0| 3.4| 2.9
5” x 7-ga x 28’| 28| 7| M| 11| 1.00| 8.3| 7.4| 6.7| 5.4| 4.5| 3.7| 3.1| 2.7| 2.3
5” x 7-ga x 30’| 30| 7| M| 11| 1.00| 6.8| 6.1| 5.4| 4.4| 3.6| 2.9| 2.4| 2.0| 1.7

All LSI Industries’ poles are guaranteed to meet the EPA requirements listed. LSI Industries is not responsible if a pole order has a lower EPA rating than the indicated wind-loading zone where the pole will be located.
CAUTION: This guarantee does not apply if the pole/bracket/fixture combination is used to support any other items such as flags, pennants, or signs, which would add stress to the pole. LSI
Industries cannot accept responsibility for harm or damage caused in these situations.
Note:
1- Poles shorter than these listed here in for each gauge have EPA rating equal to or greater than what is provided in this table. To Confirm EPA ratings on shorter poles, contact LSI Industries.
LSI Industries Inc. 10000 Alliance Rd. Cincinnati, OH 45242
• www.lsicorp.com
800-436-7800
• ©LSI Industries Inc. All Rights Reserved. Specifi cations subject to change without notice.

Page 6/6 Rev. 07/14/22
SPEC.1068.B.0722