HD1100 Warehouse Scanner

Product Information

Specifications

• Model: HD1100

• Wireless Connection: 2.4G

• Barcode Transmission Modes: Real Mode, Storage Mode, No Data
  Loss Mode

• Power and Sleep Settings: Auto Sleep Time (2 minutes, 10
  minutes, 20 minutes, 8 hours), Sleep Mode Off

• Interface Settings: USB-HID, USB Virtual COM

• Letter Size Settings: Capital Letters Only, Lowercase Only

• Barcode Scanning Modes: Continuous Mode, Automatic Mode

• Sound Signal Settings: Beep On, Beeper Off

• Reverse Code Scanning: Enabled

• Prefix Settings: Prefix Display Disabled, Prefix Display
  Enabled, Adding a Prefix

• Suffix Settings: Suffix Display Disabled, Suffix Display On,
  Adding a Suffix

• Character Hiding in Barcode: Character Hiding Disabled,
  Character Hiding Enabled

• Initial and Final Signs: Saving Settings

Product Usage Instructions

Restore the Scanner to Factory Settings

To restore the scanner to factory settings:

1. Scan the code “Factory settings (decoding functions)”

Wireless Connection Settings

To achieve a wireless connection via radio communication:

1. Connect the USB receiver to the computer’s USB port
2. Scan the 2.4G code with the scanner

Barcode Transmission Modes

• Real Mode: Barcodes are sent directly to the computer
  immediately after scanning

• Storage Mode: Scanned codes are stored in the scanner’s
  internal memory for later transfer to a computer

• No Data Loss Mode: Codes are sent to the computer immediately
  after scanning when the scanner is within range of wireless
  operation. Once the scanner is out of wireless range, the scanned
  codes are stored in the device’s internal memory. To transfer the
  stored data to the target device, scan the Data Transfer code when
  wireless communication is ensured again

Power and Sleep Settings

To set the auto sleep time:

1. Scan the code “Set auto sleep time”
2. Scan the code with the appropriate time (2 minutes, 10 minutes,
   20 minutes, or 8 hours)

To disable sleep mode:

1. Scan the code “Sleep mode off”

Interface Settings

To change the interface settings:

1. Scan the code for the desired interface setting:
   • “USB-HID” for USB-HID (default)
   • “USB Virtual COM” for USB Virtual COM

Letter Size Settings

To set the letter size:

1. Scan the code for the desired letter size:
   • “Capital letters only” for capital letters only
   • “Lowercase only” for lowercase only

Barcode Scanning Modes

To switch between barcode scanning modes:

1. Scan the code for the desired scanning mode:
   • “Continuous mode” for continuous mode
   • “Automatic mode” for automatic mode

Sound Signal Settings

To change the sound signal settings:

1. Scan the code for the desired sound signal setting:
   • “Beep on” to enable beep (default)
   • “Beeper off” to disable beep

Reverse Code Scanning

To enable reverse code scanning:

1. Scan the code “Enabled”

Prefix Settings

To set the prefix:

1. Scan the code “Display Prefix Enabled”

2. Scan the code “Add Prefix”

3. Scan the code with the appropriate characters from the
   character table (see ASCII table) to be the prefix

4. Scan the code “Save Settings”

Suffix Settings

To set the suffix:

1. Scan the code “Suffix display enabled”

2. Scan the code “Adding suffix”

3. Scan the code with the appropriate characters from the
   character table (see ASCII table) to be the suffix

4. Scan the code “Saving settings”

Character Hiding in Barcode

To hide individual digits in the barcode:

1. Scan the code “Character hiding enabled”

2. Scan the code “Start characters” or “End characters” depending
   on whether the digits from the beginning or end of the barcode are
   to be hidden

3. From the character table, scan the two codes corresponding to
   the digit to be hidden

4. Scan the code “Save settings”

FAQ (Frequently Asked Questions)

Q: How do I restore the scanner to factory settings?

A: To restore the scanner to factory settings, scan the code
“Factory settings (decoding functions)”

Q: How do I achieve a wireless connection with the

scanner?

A: Connect the USB receiver to the computer’s USB port, and then
scan the 2.4G code with the scanner

Q: How do I change the auto sleep time of the scanner?

A: Scan the code “Set auto sleep time”, and then scan the code
with the appropriate time (2 minutes, 10 minutes, 20 minutes, or 8
hours)

Q: How do I disable sleep mode on the scanner?

A: Scan the code “Sleep mode off”

Q: How do I switch between USB-HID and USB Virtual COM

interface settings?

A: Scan the code for the desired interface setting: “USB-HID”
for USB-HID (default) or “USB Virtual COM” for USB Virtual COM

Q: How do I change the letter size settings on the

scanner?

A: Scan the code for the desired letter size: “Capital letters
only” for capital letters only or “Lowercase only” for lowercase
only

Q: How do I switch between continuous mode and automatic mode

for barcode scanning?

A: Scan the code for the desired scanning mode: “Continuous
mode” for continuous mode or “Automatic mode” for automatic
mode

Q: How do I enable/disable the sound signal on the

scanner?

A: Scan the code for the desired sound signal setting: “Beep on”
to enable beep (default) or “Beeper off” to disable beep

Q: How do I enable reverse code scanning on the scanner?

A: Scan the code “Enabled”

Q: How do I set a prefix before scanning barcodes?

A: Scan the code “Display Prefix Enabled”, then “Add Prefix”,
then scan the code with the appropriate characters to be the
prefix, and finally scan the code “Save Settings”

Q: How do I set a suffix after scanning barcodes?

A: Scan the code “Suffix display enabled”, then “Adding suffix”,
then scan the code with the appropriate characters to be the
suffix, and finally scan the code “Saving settings”

Q: How do I hide individual digits in the barcode?

A: Scan the code “Character hiding enabled”, then scan the code
“Start characters” or “End characters” depending on the position of
the digits to be hidden, then scan the two codes corresponding to
the digit to be hidden from the character table, and finally scan
the code “Save settings”

Q: How do I save the settings on the scanner?

A: Follow the specific instructions for each setting mentioned
above to save the desired settings

User Manual HD1100

Restore the scanner to factory settings
Factory settings (decoding functions)
Default settings (features wireless connection)
Wireless connection settings
To pair the USB receiver with the scanner and achieve a wireless connection via radio communication, connect the receiver to the USB port of the computer, and then scan the “2.4G” code with the scanner.
2.4G

Barcode transmission modes
Real mode In real mode, barcodes are sent directly to the computer immediately after scanning.
Real mode enabled Storage mode In storage mode, scanned codes are stored in the scanner’s internal memory for later transfer to a computer.
Storage mode enabled

No data loss mode In no-data-loss mode, codes are sent to the computer immediately after scanning when the scanner is within range of wireless operation. Once the scanner is out of wireless range, the scanned codes are stored in the device’s internal memory. In order to transfer the stored data to the target device, once wireless communication is again ensured, scan the “Data transfer” code.
No data loss mode enabled Attention. Before activating the no data loss mode, it is recommended to scan the “Delete stored data” code to clear the device’s internal memory. Storage mode options
Display of the total amount of stored data
Data transmission

High data rate (default)
Low data transfer speed Usunicie zapisanych danych
Power and sleep settings
Battery charge level Immediate sleep of the scanner

To set the time after which the scanner should go into sleep mode, first scan the code “Set auto sleep time, and then scan the code with the appropriate time.
Setting the auto sleep time 2 minutes (default) 10 minutes 20 minutes 8 hours

Sleep mode off
Interface settings
USB-HID (default)
USB Virtual COM
Letter size settings
Capital letters only Lowercase only

Converting to uppercase/ lowercase letters
No letter substitution (default)
Barcode scanning modes

Continuous mode

Automatic mode

In order to return to scanning codes with the scan button, scan the code “Factory settings”

Setting end marks

Disabled

CR

LF + CR

TAB

LF

ETX

Sound signal settings

Beep on (default)

Beeper off

Reverse code scanning

Enabled

Setting the Prefix

Disabled

Prefix display disabled

Prefix display enabled

Adding a prefix

Saving settings

In order to set the Prefix, first scan the code “Display Prefix Enabled”, then “Add Prefix”, then from the character table read the code with the appropriate characters (see ASCII table) to be the prefix, and finally it is necessary to scan the code “Save Settings”.
Suffix Setup

Suffix display disabled

Suffix display on

Adding a suffix

Saving settings

To set the suffix, first scan the code “Suffix display enabled”, then read the code “Adding suffix”, from the character table scan the code with the appropriate characters (see ASCII table) to be the suffix and finally read the code “Saving settings”.

Hiding characters in the barcode

Character hiding disabled

Character hiding enabled

Initial signs

Final signs

Saving settings

To hide individual digits in the barcode, first scan the code “Character hiding enabled”, then scan the code “Start characters” or “End characters, depending on whether the digits from the beginning or end of the barcode are to be hidden. From the character table at the end of the instructions, scan the two codes corresponding to the digit to be hidden. After completing the above steps, finally read the code “Save settings”.
For example: The code is 123456789 The digit to be hidden is 1. Scan the code “0” and “1” from the numeric code table, and again the scanned code will be 23456789.

Annex 1 Numerical codes

Appendix 2 ASCII character table

HEX DEC

OPIS

HEX DEC OPIS HEX DEC

OPIS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>