Petavern B0BZD257J1 Dog Training Collar 2 Pack Instruction Manual
- June 15, 2024
- PETAVERN
Table of Contents
DOG TRAINING COLLAR
Instruction Manual
Read The Manual Before Using
Package content
Product Overview
Key Function
-
Antenna : transmit the signal strongly.
-
LED light : Press tolight it, press again to be off.
-
LCD screen : Show the modes, levels and channels.
-
Shock button : Press lo choose Shock mode, the screen press +or – button to adjust the levels from0 —- 20, press Shock button again to make the Receiver shock.
-
Vibration button : Press to choose Vibration mode the screen show , press + or— button to adjust the levels from 0 —- 20, press Shock button again to make the Receiver vibrate
-
Sound button : Press to choose Sound mode, the screen show , don’t need to adjust the levels, just press to make the receiver sound Bee~~.
-
+ button : press + o increase the training levels.
-
button : press – o reduce the training levels.
-
Channel button : choose your training channel CH1
-
Switch ON/OFF of the remote.
-
Light button : Press to light the LED of the Remote, press again, the LED will be off; If you press this button 2 seconds, the white LED on the Receiver will be on, press 2 seconds again, the White LED will be off, if you don’t press it again, the White
LED will be off automatically after 5 minutes. -
Charging hole of the Remote
-
Power button of the receiver : press to turn on the Receiver, press again to turn off it
-
Shock static electrode : Conduct the safe static; To install the rubber cap, reach to pet’s skin
-
Charging hole of the Receiver.
-
Indicator light of the receiver: the light will be on when press the shock/vibration/sound button; When charging, it flash
Charging before using
Notes:
-
The battery icon on the display will flash while the Remote controlis charging. The battery icon will stop flashing and reflect a full status when completely charged. The battery icon on the display will indicate a space status if the Remate control runs out of power.
-
The Receiver’s LED status light will light up and flash in a breathing light while charging; After completely charged, the LED status light will coase flashing and remain on. When the Receiver is charging, it goes.
into sleep mode, which means it can’t receive signals and can’t be controlled by the Remote control. The LED status light will blink every second when the Receiver s low. -
Make sure the charging port is dry before charging the Receiver.
Product switching on/off
-
To switch the Remots cantrol on, toggle the on/off button on the.
Remote cantrol to the unlocked pasition; Ta switch the Remote control off, flip the on/off button to the locked position -
The display backiight will stay on for 10 seconds after the Remote control is switched on: I no further activity is performed, the backlight will switch off. To switch on the backlight, press any button on the Remote control
-
If there i no additional operation, the LCD display will switch off after 30 seconds and can be switched back on by pressing any button on the Remote control
-
Pressthe Receiver’s power switch button, the Receiver s switched on, the LED status light wil flash once, while the Receiver makes a beep sound; Press the Receiver’s power switch button again, the Receiver s switched off, the LED status light willflash again, while the Receiver makes twobeep sound
-
The LED status light will flash every 7 seconds when the Receiver is switched on, indicating that itis in working condition and ready to receive signals from the Remote control
3.1 the Receiver does not receive an operational signal for 5 minutes, itwill enter standby mode, which may be accessed by pressing the shock button/vibrate button/beep button on the Remote control
Test training mode
-
Tesithe etectric shock function
Connect the test light to the two static electrodes of the Receiver, press the shock button of the Remote control (ensure the intensity level is more than 0) and the test light willlight up.
-
Testihe vibration function
Press the vibrate button of the Remote conirol (ensure the intensity level is more than 0) and the Receiver will vibrate.
-
Test the beep function
The Receiver will beep if you press the beep button of the Romote control (no need to adjust the intensity lovel for this operation, simply 0 is displayed)
-
Trest the LED lights function
Press the light button of the Remote control and the Torch LED on top of the Remate control will light up. Press and hold the light button on the Remate control for 2 seconds and the LED status light on the Receiver will light up.
Wearing the Receiver collar
- Thread the collar through the Receiver.
- Place the Receiver collar around the dog’s neck
- Tighten as tightly as you can fit through one fingertip.
Notes:
You may need to cut a section of the collar off if the dog is really little.
To prevent from coming apart, fuse the interface (position A) with alighter if
required
Ifyour dog isn’t responding to the electric shock, consider these solutions.
- If the dog’s hair is 100 long, it can be ruffled to the sides so that the Receiver’s static electrodes can reach the dog’s skin
- Extended silicone caps can also be fitted if the dog’s hair is toolong.
- Finally, directly shaving the dog’s neck ust before putting on the Receiver wilallow the stalic electrodes toreach thedog’s skin.
Finding the most appropriate training level for your dog
-
Follow these steps to smoothly start training your dog with the tone button :
– Spend 10-15 minutes per day for 2-3 days helping your dog understand the tone.
– Associate the tone with reward and praise (some also use the tone as a warning)
– Push the tone button for 2 seconds.
– Reward your dog with verbal praise when you release
– Allow 2-5 seconds before you repeat the process.
Quick Tip : Vary the rewards while training for the tone function As 500n as your dog starts to anticipate a reward with the tone, you’ve succeeded in this phase. -
How to find the best Shock Level :
Very important : Always begin with the lowest intensity level of electric shock, gradually raise the intensity level, follow these steps to find the optimum level :
– Adjust the intensity level starting with level 1 on the LCD display on the Remote control, then press the shock button to observe how your dog reacts
– Gradually increase the intensity level of the electric shock until your dog responds to the shock.
If you do not notice any response from your dog, you can increase the shock intensity level again – Observe and record your dog’s reactions at all times, as well as the shock’s intensity level; Interact with your dog to determine the optimal training level Quick Tip : -
Toggling the ON/OFF button of the Remote Control to the locked position, that’s supposed to turn the Remote Control off 1o prevent misoperation.
2.1 the electric shock function is not expected to be used, you could twist out the shock static electrode of the Receiver.
Frequently Asked Questions (FAQs)
Q: When | press the Remote control button, my pet does not react.
A 1. Ensure the Receiver is turned on 2. It's possible that a low battery in the Remote control and Receiver is causing the Remote control distance to be lowered when you first use it. 3. The Remote control distance can be affected by a variety of factors such as topography, weather, vegetation, and the transmission of other radio equipment 4. Increase the electric shock or vibration's intensity level 5. Ensure that the Receiver's static electrodes are close to the dog's skin.
Q: The receiver will not respond to the operational signals from the Remote control
A 1. Check o seeif the Receiver and Remote control are properly paired. 2. Check the Remote control's display for the channel icon to determine whether itis chosen on the receiver s paired channel 3. Make sure that the Remote control and Receiver are both switched on. lithis is not feasible, finish the pairing by going to the Pairing the Remote control and Receiver page
Q: What should the duration of each dog training session be?
A:10-15 minutes,
Q: What should | do if the dog training collar doesn't work?
A: 1. Check the power level of the Remote control and Receiver, then recharge itif itis low. 2. In vibrate or shack mode. Check the intensity level and ensure that the level is over 0 3. Checkif the Receiver is enabled, please press the power switch button to activate it. 4. Check the channel, press the CH button to turn it back on if you have picked another channel 5. Re-pairing the Remote control and Receiver.
Important Security Information
WARNING
-
Do not use this product if your dog is aggressive or exhibits aggressive behaviour frequently. Aggressive dogs can cause serious injury of even death to their owners and others.
Please follow the manufacturer’s directions while using the product.
We are not liable for any damages or injuries resulting from incorrect use. -
Do not use the device on dogs who are less than three months old weigh iess than eight pounds,are old or pregnant,easily scared aggressive,or in heat,or are otherwise in poor condition!
-
Shock mode is always the last choice! Before using the shock mode, you should first try the Beep/Light/Vibration mode for your pet in turn.
-
Do not charge this product with a chareger of more than 5 volts.
-
This product is not a toy and should be kept out of the reach of children.
-
Ploase unplug the product from the power supply if it will not be used for an extended period of time.
-
When the product stops working effectively due to a drop,damage, outside usage.or water infiltration,do not use t.The product should be fixed by the manufacturer o its after-sales service to avid injury.
-
Take the dog raining colar off if the dog s alone at home/somewhere or you do not train the dog!
-
Do not attach the dog leashes to this training collar!
-
It s forbidden to use the product in extremely hot (above 40 degrees Celsius) or extremely cold (below 0 degrees Celsius) environments.
-
During dog training,safety is of utmost importance.Please keep yourself and your dog in a safe range during dog trauning to avoid injuring others Make sure that the leash is strong enough and of the right length to keep.
the dog within a safe range at all times and that you can pull the dog if it runs off unexpectedly.
CAUTIONS
Because the electrostatic current generated when the product s shocked is very
low, only 0.01 amps, the electronic dog trainer products are highly safe and
will not burn the skin of the dog’s neck. Ulcers are frequently caused by
bacterial infection, thus it’s critical to wear the collar appropriately.
Wearing the collar too long or 0 tight can cause discomfort for the dog’s
neck, as well as skin damage and infection Your dog’s skin may be damaged if
you use the product incorrectly.
Please take the following steps to guarantee your dog’s safety and comfort:
- Only correct and educate one negative habit at a time; If you train too many items at once, your dog will tum resistantto training.
- Startwith the vibration function instead of using electric shocks on the dog – Always keep an eye on the dog’s reaction and make sure the training isn’t too strenuous.
- The dog trainer collar should not be worn for more than 12 hours a day.
- Adjust the position of the collar every 1-2 hours.
- Check the posilion of the receiver on a frequent basis to prevent it being squeezed too tightly and to ensure that the operating instructions are followed
- Every week regularly wipe the dog’s neck and the Receiver’s contact area with a towel.
- If you see a rash or damaged skin, discontinue wearing the collar until it heals. Consult your veterinarian if the problem persists more than 48 hours.
- If a pull—cord is required, it’s better to wear a separate collar strap rather than attach ed to the Receiver collar.
