OLIGHT Oclip Review Clip Light User Manual

OLIGHT Oclip Review Clip Light

Product information

Specifications

ventilation conditions, and these biases may affect the results of
testing.
Charge type| USB-C
Cable Length| 0.25m
Input| 5V/1A
Charging time| About 1.5 hours
Dimensions| (L)48.5(W)21(H)23mm
Weight| 30g/1.06oz (Including Battery)
Water resistance| IPX5

**Product Overview

**

A clip-on light with dual light sources.

Features include:

• On/Off Battery Level Indicator
• Magnetic base
• High performance LED
• Red: Charging, Green: Charging Completed
• Lanyard hole

Product Usage Instructions

1st batch
To charge the product, follow these steps:

1. Connect the USB-C Charging Cable to the product.
2. Connect the other end of the cable to a power source.
3. The battery level indicator will show red when charging and green when charging is completed.

On/Off
To turn the product on or off, follow these steps:

• To turn on the product, press and hold the button for more than 1 second.
• To turn off the product, press and hold the button for more than 2 seconds.

Lockout/Unlock
To lock or unlock the product, follow these steps:

• When the product is off, press and hold the side switch for about 2 seconds to access the lockout mode.
• The product will enter the moonlight mode first and then switch off to signal the lockout mode.
• The red indicator at the center of the switch will be on for a short time to indicate that the product is in lockout mode.
• To unlock the product, continue holding the side switch for over one second until the moonlight mode is on again.

Moonlight mode
To activate Moonlight mode, follow these steps:

• Press and hold the button for 1 second or more when the flashlight is off.
• If the last used mode was Moonlight mode, simply press the button to activate it.

Change brightness level (White light mode only)
In white light mode, you can change the brightness level. Follow these steps:

• Long press the button to change the brightness.
• The output starts from the current brightness and changes in the order of Low -> Medium -> High -> Low.
• Release the button to set the desired brightness level.

Strobe (White light mode only)
In white light mode, you can activate the strobe feature. Follow these steps:

• Triple-press the button to activate the strobe mode.

Red light mode
In red light mode, you can switch between different modes. Follow these steps:

• Press and hold the button for more than 0.5 seconds to switch to red light mode.
• Press and hold the button for more than 0.5 seconds again to switch between different red light modes.

White light beacon
In white light mode, you can turn on the white light beacon. Follow these steps:

• Double-press the button to turn on the white light beacon.

Battery indicator
The product has a battery indicator that shows the battery level. Follow these steps:

• Double press the button to switch between battery indicator modes (Red light or White light).
• In battery indicator mode, triple-press the button to switch between red and white light modes.

Frequently Asked Questions (FAQ)

• Q: How long does the battery last?
• A: The runtime may vary depending on the external temperature and ventilation conditions, and these biases may affect the results of testing.
• Q: How long does it take to charge the product?
• A: The charging time is about 1.5 hours.
• Q: What is the water resistance rating?
• A: The product has an IPX5 water resistance rating.
• Q: What is included in the box?
• A: The box includes the Oclip, USB-C Charging Cable, and a user manual.

IN THE BOX

Multi-language dictionary

Operating instructions

Charge,
see Figure 2.

On/Off,
see Figure 3.

• Single press the button to turn on and off. When turned off, the current mode will be memorized. (Strobe and White Light Beacon can’t be memorized)

Lockout / Unlock,
see Figure 4.

When the light is off, press and hold the side switch for about 2 seconds to access the lockout mode. The light will enter the moonlight mode first and then switch off to signal the lockout mode. The red indicator at the center of the switch will be on for a short time to indicate that the light is still in lockout mode. To unlock it, continue holding the side switch for over one second until the moonlight mode is on again.

Moonlight mode,
see Figure 5.

• To activate Moonlight mode, press and hold the button for 1 second or more when the flashlight is off. If the last used mode was Moonlight mode, simply press the button.

Change brightness level
(White light mode only), see Figure 6.

In the white light mode, long press the button to change the brightness. The output starts from the current brightness, and changes in the order of Low->Medium->High->Low. Release the button to select the brightness.(Note: Moonlight mode are not included in this cycle).

Strobe mode,
see Figure 7.

• To turn Strobe on, quickly press the button three times or more when the light is off.
• Press or press and hold to turn off the Strobe.

Red light mode,
see Figure 8.

• While the light is on or off, double-press to enter red light mode.
• Single-press to turn off and the current mode will be memorized when the light is turned on again.

Switch between red and white light modes,
see Figure 9.

When the light is on, double press the button to switch between red light mode and white light mode.

Change red light mode,
see Figure 10.

In the red light mode, press and hold for more than 0.5 seconds to switch to the red light blink, release the button, and press and hold for more than 0.5 seconds to go back to the constant red light.

Turn on the white light beacon,
see Figure 11.

Turn on the white light beacon by quickly pressing the button three times when the light is off or in red light mode. To exit the mode, simply press or press and hold the button.

Battery Indicator

See Figure 12. DANGER

• Do not disassemble the product.
• Do not throw the product into the fire, it may cause the battery to burn or even explode, causing unpredictable disasters.

CAUTION

• Do not look directly at the light source or shine it into your eyes, as this may cause temporary blindness or permanent damage to your eyes.
• Do not obstruct the lens, or else the energy emitted from the light may cause the object to burn.
• Don’t place, charge, or use this light in a car where the temperature inside may exceed 60°C or in similar environments. Do not immerse the product in water or other liquid as it will damage the product.
• Do not place the light in a dusty environment as dust may enter the switch and cause functional failure.
• The clip is magnetic, and the metal powder adsorbed on the surface will affect the function, please clean it immediately.

NOTICE

• Please only use the TYPE-C charging cable to charge the product to avoid damage.
• Charge the product completely before storing it for a long period.
• If the product is carried, or transported, please lock the product.
• When the charging port is not in use, keep the dust cover closed to prevent dust or foreign objects from entering.

REMARK

• Do not put a hot light into any type of fabric bag or fusible plastic container.
• Non-pet toys.
• When the ambient temperature is below 0°C/32.0 °F

Table 1 Specifications

The above data are tested per ANSI/NEMA FL 1-2009 standard in Olight’s labs for reference. The tests are performed indoors under a room temperature of 25 degrees Celsius with windless conditions. The runtime may vary depending on the external temperature and ventilation conditions, and these biases may affect the results of testing.

Table 2 USB-C Charging Cable

Table 3 Multi-language dictionary

• Moonlight
• Low
• Medium
• High
• Strobe
• White light
• Red light
• White light beacon
• Press
• Double press
• Triple press
• Press and hold

WARRANTY

Within 30 days of purchase:
Contact the original seller for repair or replacement.

Within 2 years of purchase:
Contact Olight for repair or replacement. If you experience quality problems or damage with low-value fittings like lanyards or clips within 30 days of purchase under normal use conditions, please contact our after-sale service. For issues that occur after 30 days or for damage caused by abnormal use conditions, we provide conditional quality assurance as appropriate.

USA Customer Support  cs@olightstore.com

Global Customer Support
contact@olightworld.com Visit www.olightworld.com to see our complete product line of portable illumination tools.

Dongguan Olight E-Commerce Technology Co., Ltd 4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town, Dongguan City, Guangdong, China.

Made in China

References

• Olight | Illuminate Your World.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>