tp-link EAP110 Outdoor Omada Access Point Instructions

tp-link EAP110 Outdoor Omada Access Point

Specifications

• Product Name : Omada Outdoor Access Point
• Model Number : EAP110-Outdoor
• Operating Frequency : 2412MHz – 2472MHz (20dBm)

Regulatory Compliance
This product complies with the following regulations

• FCC Compliance
• CE Mark Warning
• EU Declaration of Conformity

FCC Compliance Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not approved by TP-Link USA Corporation could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits. To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter.

CE Mark Warning
This product is classified as a class A product. In a domestic environment, it may cause radio interference, and the user may be required to take adequate measures to address the interference.

EU Declaration of Conformity
TP-Link declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU, and (EU)2015/863. The original EU Declaration of Conformity can be found at https://www.tp-link.com/en/ce.

Product Usage Instructions

Follow the instructions below to use the Omada Outdoor Access Point

Mounting the Access Point

1. Select a suitable location for mounting the access point outdoors.
2. Ensure that the access point is securely attached to a stable surface.
3. Make sure the access point is protected from extreme weather conditions.

Connecting Power

1. Connect the I.T.E. Power Supply (Model Number: TL-POE2406) to the access point.
2. Ensure that the power supply is securely connected to a power source.

Network Configuration

1. Connect the access point to your network using an Ethernet cable.
2. Configure the network settings of the access point according to your network requirements.

Access Point Management

1. Access the management interface of the access point using a web browser.
2. Log in with the default credentials or set up a new username and password.
3. Manage and customize the settings of the access point as needed.

Troubleshooting
If you encounter any issues with the access point, refer to the user manual or contact TP-Link support for assistance.

Frequently Asked Questions (FAQ)

• Q: What is the maximum operating frequency of the access point?
  A: The maximum operating frequency is 2412MHz – 2472MHz with a transmitted power of 20dBm.

• Q: Where can I find the EU Declaration of Conformity?
  A: The EU Declaration of Conformity can be found at https://www.tp- link.com/en/ce.

• Q: What should I do if I experience radio interference?
  A: If you experience radio interference in a domestic environment, take adequate measures to address the interference.

• Q: How can I troubleshoot issues with the access point?
  A: Refer to the user manual or contact TP-Link support for assistance with troubleshooting.

Regulatory Compliance

Outdoor EAP
© 2023 TP-Link 1910013244 REV1.3.0

For Class A Outdoor EAP with adapter

FCC Compliance Information Statement

• Product Name : Omada Outdoor Access Point
• Model Number : EAP110-Outdoor

• Responsible party:
  • TP-Link USA Corporation
  • Address: 10 Mauchly, Irvine, CA 92618
  • Website: https://www.tp-link.com/us/
  • Tel: +1 626 333 0234
  • Fax: +1 909 527 6804
  • E-mail: sales.usa@tp-link.com

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note : The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter.”

• Product Name: I.T.E. Power Supply
• Model Number: TL-POE2406
• Responsible party:
  • TP-Link USA Corporation
  • Address : 10 Mauchly, Irvine, CA 92618
  • Website : https://www.tp-link.com/us/
  • Tel : +1 626 333 0234
  • Fax : +1 909 527 6804
  • E-mail: sales.usa@tp-link.com

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
Issue Dat e: 2023-08-14

CE Mark Warning

This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

OPERATING FREQUENCY (the maximum transmitted power)

2412MHz—2472MHz(20dBm)

EU Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU Declaration of Conformity may be found at https://www.tp- link.com/en/ce.

UKCA Mark

UK Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017.
The original UK Declaration of Conformity may be found at https://www.tp- link.com/support/ukca

RF Exposure Information

• This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection.
• The device complies with RF specifications when the device used at 20 cm from your body.

Canadian Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license exempt RSS(s). Operation is subject to the following two conditions

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

For EAP110-Outdoor
This radio transmitter (IC: 8853A-EAP110OD / Model: EAP110-Outdoor) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list below, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

• Antenna Two 2.4GHz 3dBi external omnidirectional antennas

Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Industry Canada Statement
CAN ICES-3 (A)/NMB-3(A)

Korea Warning Statements
VCCI‑A

NCC Notice & BSMI Notice

Safety Information

• Keep the device away from fire or hot environments. DO NOT immerse in water or any other liquid.
• Adapter should be used indoors where the ambient temperature is lower than or equal to 40 ℃ .
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• Do not use damaged charger or USB cable to charge the device.
• Do not use any other chargers than those recommended.
• Do not use the device where wireless devices are not allowed
• Adapter shall be installed near the equipment and shall be easily accessible.
• Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don’t hesitate to contact us.
• Operating Temperature: ‑30℃ – 65℃ (‑22 ℉ – 149 ℉ )
• This product uses radios and other components that emit electromagnetic fields. Electromagnetic fields and magnets may interfere with pacemakers and other implanted medical devices. Always keep the product and its power adapter more than 15 cm (6 inches) away from any pacemakers or other implanted medical devices. If you suspect your product is interfering with your pacemaker or any other implanted medical device, turn off your product and consult your physician for information specific to your medical device.

Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

Explanation of the symbols on the product label

Note: The Equipment marking is at the bottom of the device. Symbols may vary from products.

For Class B EAP with adapter
FCC Compliance Information Statement

• Product Name : Omada Outdoor Access Point
• Model Number: EAP113-Outdoor / EAP225-Outdoor / EAP610-Outdoor / EAP650-Outdoor / EAP115-Bridge / EAP211-Bridge / EAP215-Bridge

• TL-POE2412G (for EAP225-Outdoor) T480050-2-POE (for EAP610-Outdoor) T480038-2-POE (for EAP650-Outdoor)

• T240050-2-POE (for EAP115-Bridge / EAP211-Bridge / EAP215-Bridge)

• Responsible party:

  • TP-Link USA Corporation
  • Address : 10 Mauchly, Irvine, CA 92618
  • Website : https://www.tp-link.com/us/
  • Tel : +1 626 333 0234
  • Fax : +1 909 527 6804
  • E-mail: sales.usa@tp-link.com

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note : The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm (for EAP113-Outdoor / EAP225-Outdoor / EAP650-Outdoor / EAP115-Bridge / EAP211-Bridge / EAP215-Bridge) / 25cm (for EAP610-Outdoor) from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter.”

• Product Name : I.T.E. Power Supply
• Model Number: TL-POE2412G / T480050-2-POE / T480038-2-POE / T240050-2-POE
• Responsible party:
• TP-Link USA Corporation
• Address : 10 Mauchly, Irvine, CA 92618
• Website : https://www.tp-link.com/us/
• Tel : +1 626 333 0234
• Fax : +1 909 527 6804
• E-mail : sales.usa@tp-link.com

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
Issue Date : 2023-08-14

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

OPERATING FREQUENCY (the maximum transmitted power)

• For EAP113-Outdoor
  • 2412MHz—2472MHz(20dBm)
• For EAP225-Outdoor / EAP610-Outdoor / EAP650-Outdoor / EAP115-Bridge / EAP211-Bridge / EAP215-Bridge:
  • 2412MHz—2472MHz(20dBm)
  • 5180MHz—5240MHz(23dBm)
  • 5260MHz—5320MHz(23dBm)
  • 5500MHz—5700MHz(30dBm)
• For EAP115-Bridge / EAP211-Bridge / EAP215-Bridge: 5180MHz—5240MHz(23dBm)
  • 5260MHz—5320MHz(23dBm)
  • 5500MHz—5700MHz(30dBm)

EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU Declaration of Conformity may be found at https://www.tp- link.com/en/ce.

RF Exposure Information

• This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection.
• The device complies with RF specifications when the device used at 20cm (for EAP113-Outdoor / EAP225-Outdoor / EAP650-Outdoor / EAP115-Bridge / EAP211-Bridge / EAP215-Bridge) / 25cm (for EAP610-Outdoor) from your body.

National Restrictions
For EAP225-Outdoor / EAP610-Outdoor / EAP650-Outdoor / EAP115-Bridge / EAP211-Bridge / EAP215-Bridge:

• Frequency band: 5150 – 5250 MHz
  Indoor use : Inside buildings only. Installations and use inside road vehicles and train carriages are not permitted. Limited outdoor use: If used outdoors, equipment shall not be attached to a fixed installation or to the external body of road vehicles, a fixed infrastructure or a fixed outdoor antenna. Use by unmanned aircraft systems (UAS) is limited to within the 5170 – 5250 MHz band.

• Frequency band: 5250 – 5350 MHz
  Indoor use : Inside buildings only. Installations and use in road vehicles, trains and aircraft are not permitted. Outdoor use is not permitted.

• Frequency band: 5470 – 5725 MHz
  Installations and use in road vehicles, trains and aircraft and use for unmanned aircraft systems (UAS) are not permitted.

UKCA Mark

UK Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017.

The original UK Declaration of Conformity may be found at https://www.tp- link.com/support/ukca

National Restrictions
For EAP225-Outdoor / EAP610-Outdoor / EAP650-Outdoor / EAP115-Bridge / EAP211-Bridge / EAP215-Bridge:

Attention: In Great Britain, the operation in the frequency range 5150MHz – 5350MHz is only permitted indoors.

Canadian Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

For EAP225-Outdoor
This radio transmitter (IC: 8853A-EAP225OD / Model: EAP225-Outdoor) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list below, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Antenna

• Two 2.4GHz 3dBi external omnidirectional antennas
• Two 5GHz 4dBi external omnidirectional antennas

Caution

• For EAP225-Outdoor / EAP610-Outdoor
  1. The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; 5150 MHz to 5350 MHz is restricted to indoor operations in Hong Kong.
• For EAP650-Outdoor / EAP115-Bridge / EAP211-Bridge / EAP215-Bridge:
  1. The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)

Korea Warning Statements

• NCC Notice & BSMI Notice
• EAP610-Outdoor / EAP650-Outdoor / EAP115-Bridge / EAP211-Bridge / EAP215-Bridge：
• EAP225-Outdoor

Safety Information

• Keep the device away from fire or hot environments. DO NOT immerse in water or any other liquid.
• Adapter should be used indoors where the ambient temperature is lower than or equal to 40 ℃ .
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• Do not use damaged charger or USB cable to charge the device.
• Do not use any other chargers than those recommended.
• Do not use the device where wireless devices are not allowed
• Adapter shall be installed near the equipment and shall be easily accessible.
• Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don’t hesitate to contact us.
• Operating Temperature:
  • For EAP113-Outdoor : ‑30℃ – 65℃ (‑22 ℉ – 149 ℉ )
  • For EAP115-Bridge / EAP211-Bridge / EAP215-Bridge : ‑40℃ – 70℃ (‑40 ℉ – 158 ℉ ) For others: ‑30℃ – 70℃ (‑22 ℉ – 158 ℉ )

This product uses radios and other components that emit electromagnetic fields. Electromagnetic fields and magnets may interfere with pacemakers and other implanted medical devices. Always keep the product and its power adapter more than 15 cm (6 inches) away from any pacemakers or other implanted medical devices. If you suspect your product is interfering with your pacemaker or any other implanted medical device, turn off your product and consult your physician for information specific to your medical device.

Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

Explanation of the symbols on the product label

Note: The Equipment marking is at the bottom of the device. Symbols may vary from products.

Mounting Requirements
For safety, we recommend you to use the original screws in the package when mounting. The following are alternatives to mount the device on the wall

• (For EAP610-Outdoor / EAP650-Outdoor) Use 2 screws which comply with ANSI B1.1 4#, (5#), 6# standard and are longer than 7mm.

References

• Link: Simple, secure one-click payments
• Regulatory Compliance | TP-Link
• WiFi Networking Equipment for Home & Business | TP-Link

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>