D-Link DGS-1510-28XMP Gigabit Stackable Smart Managed Switch User Guide

: June 4, 2024
: D-Link

Table of Contents

DGS-1510-28XMP Gigabit Stackable Smart Managed Switch
About This Guide
Installing Power Cord Retainer
Rack Installation
Management Options
Telnet Management
Warranty Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

28XMP Gigabit Stackable Smart Managed Switch
User Guide

CROSSIO CFL-1074 40 Inch Ceiling Fan with Light and Remote Control -
Fig

DGS-1510-28XMP Gigabit Stackable Smart Managed Switch

Layer 2+ SmartPro Stackable Switch with 24 10/100/1000Base-T PoE Ports and 4 10GBase-X SFP+ Ports

About This Guide

This guide gives step-by-step instructions for setting up switches and relative Warranty, Safety, Regulatory, and Environment Notice. Please note that the model you have purchased may appear slightly different from those shown in the illustrations. For more detailed information about your switch, its components, making network connections, and technical specifications, please refer to the User’s Guide included with your switch
Step 1- Unpacking
Open the shipping carton and carefully unpack its contents. Please consult the packing list located in the User Guide to make sure all items are present and undamaged. If any item is missing or damaged, please contact your local D-Link reseller for replacement.
– One D-Link Switch – Rack mounting bracket
– Rubber feet – Power cord
– Power cord retainer
– Console cable
– User’s Guide CD with DNA (D-Link Network Assistant) program
– One multilingual Getting Started Guide – An accessory kit for one ground screw

Step 2 – Switch Installation
For safe switch installation and operation, it is recommended that you:

Visually inspect the power cord to see that it is secured fully to the AC power connector.
Make sure that there is proper heat dissipation and adequate ventilation around the switch.
Do not place heavy objects on the switch

Desktop or Shelf Installation
When installing the switch on a desktop or shelf, the rubber feet included with the device must be attached on the bottom at each corner of the device’s base. Allow enough ventilation space between the device and the objects around it.

CROSSIO CFL-1074 40 Inch Ceiling Fan with Light and Remote Control - Fig
2

Grounding the Switch (depending on the purchased model)
This section describes how to connect the Switch to the ground. You must complete this procedure before powering on your Switch.
Required Tools and Equipment

Grounding screws (included in the accessory kit): One M4 x 6 mm (metric) pan-head screw
Grounding cable (not included in the accessory kit): The grounding cable should be sized according to local and national installation requirements. Depending on the power supply and system, a 12 to 6 AWG copper conductor is required for installation. Commercially available 6 AWG wire is recommended. The length of the cable depends on the proximity of the Switch to proper grounding facilities.
A screwdriver (not included in the accessory kit)

You can connect the Switch to a protective ground by following the steps below:

Verify if the system power is off.
Use the grounding cable to place the #8 terminal lug ring on top of the ground-screw opening.
Insert the grounding screw into the ground-screw opening.
Using a screwdriver, tighten the grounding screw to secure the grounding cable to the Switch.
Attach the terminal lug ring at the other end of the grounding cable to an appropriate grounding stud or bolt-on rack where the Switch is installed.
Verify if the connections at the ground connector on the Switch and the rack are securely attached.

CROSSIO CFL-1074 40 Inch Ceiling Fan with Light and Remote Control - Fig
1
Figure 2. Connect a Grounding Cable

Installing Power Cord Retainer

To prevent accidental removal of the AC power cord, it is recommended to install the power cord retainer together with the power cord.

With the rough side facing down, insert the Tie Wrap into the hole below the power socket.
Figure 3-1. Insert Tie Wrap to the Switch
Plug the AC power cord into the power socket of the Switch.

Figure 3-2. Connect the power cord to the Switch
Slide the Retainer through the Tie Wrap until the end of the cord.
Figure 3-3. Slide the Retainer through the Tie Wrap
Circle the tie of the Retainer around the power cord and into the locker of the Retainer.

Figure 3-4. Circle around the power cord

Fasten the tie of the Retainer until the power cord is secured.
Figure 3-5. Secure the power cord

Rack Installation

The switch can be mounted in an EIA standard-size 19-inch rack, which can be placed in a wiring closet with other equipment. To install, attach the mounting brackets to the switch’s side panels (one on each side) and secure them with the screws provided.

CROSSIO CFL-1074 40 Inch Ceiling Fan with Light and Remote Control - Fig
8 Figure 4. Attaching the mounting brackets

Then, use the screws provided with the equipment rack to mount the switch in the rack.

Installing the switch in a standard-sized equipment rack

Step 3 – Plugging in the AC Power Cord
You can now connect the AC power cord to the rear of the switch and to an electrical outlet (preferably one that is grounded and surge protec ed).

CROSSIO CFL-1074 40 Inch Ceiling Fan with Light and Remote Control - Fig
10 Figure 6. Plugging the switch into an outlet

Power Failure
As a precaution, the switch should be unplugged in case of power failure. When power is resumed, plug the switch back in.

Management Options

This system may be managed out-of-band through the console port on the front/back panel or in-band using Telnet. The user may also choose the web- based management, accessible through a web browser. Each Switch must be assigned its own IP Address, which is used for communication with an SNMP network manager or other TCP/IP application (for example BOOTP, TFTP). The Switch’s default IP address is 10.90.90.90. The user can change the default Switch IP address to meet the specification of your networking address scheme.

Web-based Management Interface
After a successful physical installation, you can configure the switch, monitor the LED panel, and display statistics graphically using a web browser, such as Microsoft’) Internet Explorer version 7.0 and higher, Firefox, Chrome or Safari.
You need the following equipment to begin the web configuration of your device:

A PC with a RJ-45 Ethernet connection
A standard Ethernet cable

Step 1 Connect the Ethernet cable to any of the ports in front panel of the switch and to the Ethernet port on the PC.

CROSSIO CFL-1074 40 Inch Ceiling Fan with Light and Remote Control - Fig
12

Step 2
In order to login and configure the switch via an Ethernet connection, the PC must have an IP address in the same range as the switch. For example, if the switch has an IP address of 10.90.90.90, the PC should have an IP address of 10.x.y.z (where x/y is a number between 0 —254 and z is a number between 1 —254), and a subnet mask of 255.0.0.0.
Open your web browser and enter http://10.90.90.90 (the factory-default IP address) in the address box. Then press .

CROSSIO CFL-1074 40 Inch Ceiling Fan with Light and Remote Control - Fig
11 Figure 8. Enter the IP address 10.90.90.90 in the web browser

The web configuration can also be accessed through the DNA. You can click the IP hyper link in the device list in the DNA to open the web GUI of devices.
NOTE: The switch’s factory default IP address is 10.90.90.90 with a subnet mask of 255.0.0.0 and a default gateway of 0.0.0.0
Step 3: When the following logon dialog box appears, enter “admin” for both the Username and Password and choose the language of the Web-based Management interface then click Login.
CROSSIO CFL-1074 40 Inch Ceiling Fan with Light and Remote Control - Fig
13 Step 4
Before entering the Web-based Management, the Smart Wizard will guide you to quickly configure some functions, such as 1p Information, User Account and SNMP Settings. If you don’t plan to change anything, click Exit to exit the Wizard and enter the Web-based Management. For a detailed look at the Smart Wizard’s functions, please refer to the Smart Wizard introduction in the user manual.

DNA (D-Link Network Assistant)
The DNA (D-Link Network Assistant) included on the installation CD is a program for discovering Switches with the same L2 network segment connected to your PC. This tool can support windows 2000, XP, Vista, and Windows 7. There are two options for the installation of DNA (D-Link Network Assistant), one is through the autorun program on the installation CD and the other is manual installation.
Option 1: Follow these steps to install the DNA (D-Link Network Assistant) via the autorun program on the installation CD.

Insert the CD into your CD-Rom Drive.
The autorun program will pop up automatically
Simply click on the “Install DNA (D-Link Network Assistant)” button and an installation wizard will guide you through the process.
After successfully installing the DNA, you can find it under Start > Programs > D-Link > DNA.
Just connect the Switch to the same L2 network segment of your PC and use the DNA (D-Link Network Assistant) to discover the Switches.

O ption 2: Follow these steps to install the DNA (D-Link Network Assistant) manually.

Insert the Utility CD into your CD-Rom Drive.
From the Start menu on the Windows desktop, choose Computer.
Double click on your CD-Rom/DVD-Rom Drive to start the autorun menu, or right click on the Drive to open the folder. Select DNA (D-Link Network Assistant) and double click on the setup.exe file.
Follow the on-screen instructions to install the utility.
Upon completion, go to Start > Programs > D-Link > DNA and open the DNA (D-Link Network Assistant).
Just connect the Switch to the same L2 network segment of your PC and use the DNA (D-Link Network Assistant) to discover the Switch. For detailed information of DNA, please refer the user manual.

Connecting The Console Port
To connect to the serial port, a special Console Cable must be used. This cable is included with this product’s packaging. The cable referred to as an RS-232 to RJ-45 connector cable specifically pinned to connect to this switch’s serial port by using the correct pin configuration. To connect to the console port of the Switch, use the following steps:

Connect the RS-232 end of the console cable to the Serial Port of the management PC.
Connect the RJ-45 end of the console cable to the Console Port of the Switch.
Open the HyperTerminal application (or any terminal emulation program capable of emulating a VT-100 terminal connection) on the management PC and configure the Properies of this connection.
a.The Bits per second should be 115200 baud.
b.The Data bits should be 8.
c.The Parity should be None.
d.The Stop bits should be 1.
e.The Flow control should be None.
Figure 9. Hyperterminal Connection Properties
Now the Switch can be turned on and access to the Switch’s CLI will be available.

Telnet Management

Users may also access the switch through Telnet using your PC’s Command Prompt. To access it from your computer, users must first ensure that a valid connection is made through the Ethernet port of the Switch and your PC, and then click Start > Programs > Accessories > Command Prompt on your computer. Once the console window opens, enter the command telnet 10.90.90.90 (depending on configured IP address) and press Enter on your keyboard. You should be directed to the opening console screen for the Command Line Interface of the switch, enter the “admin” for the default user name and password for the Switch and press the Enter key.

Additional Information
If you are encountering problems setting up your network, please refer to the user manual that came with the switch. It contains many more rules, charts, explanations, and examples to help you get your network up and running. Additional help is available through our offices listed at the back of the user manual or online. To find out more about D-Link products or marketing information, please visit the website http://www.dlink.com.