TOPRIG S60 Video Slider User Manual
- June 15, 2024
- TOPRIG
Table of Contents
TOPRIG S60 Video Slider
Specifications
- Battery compatibility: NP-F550/NP-F750/NPF 970
- Speed control range: 0.1-5.0cm/s
Product Information
General Information
In the Box
- Slider x 1
- Hexagon Wrench x 1
- Replacement Belt x 1
The following items are included in the package
- Panoramic Setting Knob
- Spirit Level
- Slider Platform
- Speed Control
- Power On/Off
- AB Setting
- Loop Mode
- Start/Stop
- Power Indicator
- DC 5V Output
- Shutter Release Port
Overview **
**
- Speed Control
- Power On/Off
- AB Setting
- Loop Mode
- Start/Stop
- Power Indicator
- Panoramic Setting Knob
- Spirit Level
- Slider Platform
- DC
- 5V Output
- Shutter Release Port
The video slider is equipped with the following features
- Brushless Motor for stability
- Adjustable Speed Dual-axis Camera Motions
- APP Control for AB Point Setting, Time-Lapse, and Silent operation
Key Features
- Brushless Motor
- Stable
- Adjustable Speed
- Dual-axis Camera Motions
- APP Control
- AB Point Setting
- Time-Lapse
- Silent
How to Install
-
Step 1: Install battery (not included)
Battery compatibility: NP-F550/NP-F750/NPF 970. -
Step 2: Install the tripod ball head (not included) onto the slider
-
Step 3: Install the camera
- Step 4: Connect the shutter extension cable (not included)
Shutter Release Port
Connect the shutter release port to the camera using a shutter extension
cable.
Product Usage Instructions
Functions
** Power On/Off
**
Power On: To power on the slider, press the power button.
Power Off: To power off, press and hold the power button for 2 seconds.
Calibration
Please calibrate the slider before use.
How to calibrate
Follow these steps
- Press the Start/Stop button after powering on.
- The slider will automatically complete the calibration.
AB Point Setting
Default AB Point
The default AB point of the slider upon powering on is shown below
There are two ways to set AB points
Default AB Point
- A: First position
- B: Second position
Customize AB Point
- Move the slider to the 1st position.
- Press the AB point setting button to set point A (indicator light A on).
- Move the slider to the 2nd position.
- Press the AB point setting button to set point B (indicator light B on).
- Setting complete.
To cancel AB point setting, press the AB point setting button again. The indicator lights A and B will both be turned off.
Cancel AB point setting
After the AB point setting is completed, press the AB point setting button
again to cancel the AB point. The indicator lights A and B will both be turned
off.
Loop Mode
The slider supports Single-loop mode and Infinite-loop mode. Single-loop
mode is the default mode.
To switch between the two modes, press the loop mode button.
Speed Control
Control the speed of the slider by rotating the speed control knob. The
speed control range is 0.1-5.0cm/s.
Stationary Object Tracking & Panoramic Mode **Setting
**
There are three shooting modes
- Pan Shooting Mode: Adjust the knob to the center.
- Focus Shooting Mode: Adjust the knob to the upper left and lower right.
- Panoramic Shooting Mode: Adjust the knob to the lower left and upper right.
App **
**
TopRig App Features
- Calibration
- AB Point Setting
- Video Shooting
- Time-Lapse
- Loop Mode
- Firmware Update
App Download
Please download the App- TopRig from Google Play Store or iOS Apple Store.
App Connect
To connect the TopRig App to the Slider S60, enable Bluetooth on your
mobile device and follow these steps
- Open the TopRig App.
- Tap “Connect Device”.
- Select the device ‘Slider_****’.
- Tap “Confirm”.
Calibration
To calibrate the slider using the app, follow these steps:
- Tap “Calibration”.
- Tap “Confirm”.
- The slider will automatically complete the calibration.
AB Point Setting
To set AB points using the app, follow these steps
Set Point A
- Tap the arrow button to move the slider to the 1st position.
- Tap “A”.
Set Point B
- Tap the arrow button to move the slider to the 2nd position.
- Tap “B”.
To cancel AB point setting, tap “Delete”.
Loop Mode
To switch between loop modes using the app, tap the loop button.
Video Shooting
Note: A camera control cable is needed for this function.
-
Step 1
Once all parameters are set, tap 「Shoot」 -
Step 2
Tap 「Start」 to start video shooting
Time-Lapse
Note: A camera shutter cable is needed for time-lapse.
User s can customize the AB point set ting based on different shooting needs.
Parameter Setting
-
Total Time: Defines how long the shoot lasts. (User setting required)
-
Interval Time: Defines how long it lasts between each photo shot. Interval time must be longer than exposure time. (User setting required)
-
Exposure Time: Defines how long the slider remain stationary. Must be longer than the camera’s exposure time. (User setting required)
-
Frame Rate: Defines the frame rate of the final video. (User setting required)
-
Number of Shots: The total number of photo shots for reference.
-
Video Length: The final length of the video for reference.
Start/Stop Time-lapse
Start
After the parameter setting, tap 「Start」.
Stop
Tap 「Stop」
Tap 「Confirm」
Firmware Update
-
Step 1
Tap 「 」 -
Step 2
Select 「Firmware Update」 -
Step 3
Tap 「Next」
Specs
Rated Voltage | 7.4 -16.8V |
---|---|
Max. Horizontal Load | 4.0kg |
Max. Vertical Load | 2.5kg |
Max. Operating Speed | 5cm/s |
Stationary Object Tracking Panoramic Angle | 55° |
Max. Travel Distance | 425mm |
Power Supply | DC 9-16.8V NP-F Battery |
Power Consumption | 0.5W |
Dimensions | 610 x 106 x 71.3mm |
Weight | 1.5Kg |
Warranty
Warranty Period
-
lf there is a quality problem that occurs within 15 days
after receiving the product, TopRig will provide complimentary maintenance or replacement. -
Under proper use and maintenance, from the date of receipt, TopRig will provide a one-year warranty on the wireless video transmission system and a three-month warranty on the accessories and cables. Free maintenance service is available during the warranty period.
-
Please keep the proof of purchase and the user manual in a safe place.
Warranty Exclusions
- Out of warranty (lf the proof of purchase is not available, the warranty will be calculated from the date the product is delivered from the factory)
- Damage caused by use or maintenance is not following the requirements of the product manual.
- Unauthorized repair, modification or disassembly.
- Damage caused by force majeure such as fret, flood, lightning strike, etc.
Warranty Process
- Add: Room 302, BLDG D, Zhiyuanyungu, 73 Guanlan Blvd, Longhua District, Shenzhen 518110
- Tel: 0086-28-84334099
FAQ
-
Q: What batteries are compatible with the slider?
A: The slider is compatible with NP-F550, NP-F750, and NPF 970 batteries. -
Q: What is the speed control range of the slider?
A: The speed control range is 0.1-5.0cm/s.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>